废轮胎热解炭黑的表面修饰及其在平版印刷油墨中的应用

Pyrolysis has the potential of transforming waste into valuable products. Pyrolytic carbon black （PCB） is one of the most important products resulting from the pyrolysis of used tires. One of the most significant applications of modified pyrolytic carbon black is its use as pigment for offset printing ink to obtain high added values. Inverse gas chromatography （IGC） results show that a large quantity of inorganic matters and carbonaceous deposit are removed by treating the pyrolytic carbon black with nitric acid solution. Plenty of active sites originally occupied by inorganic ash and coke are recovered. The surface energy of pyrolytic carbon black （TWPC） modified by titanate-coupling agent-especially the specific interaction γs^SP determined by the specific probe molecule, toluene-shows the strong interaction between the TWPC and the synthetic resins. The offset printing ink performance confirms the IGC prediction. And TWPC has the great potential of applications in printing ink industry as pigment.     

高温高压下湿空气循环中增湿塔的计算研究

Humidification is an important step in humid air turbine system. The calculation on humidification is carried out at 423.15—573.15K, 5—15MPa. The results suggest that to produce high-enthalpy moist air, high water temperature and large water flow are needed. The water temperature is the most sensitive parameter to the humidification tower. And it is better for the humidification tower to work at temperature higher than 523 K when the system pressure is higher than 5 MPa. The comparison between the model used in this paper and ideal model shows that the ideal model can be used in simulation to simply the calculation when the temperature is lower than 473 K and pressure is lower than 5 MPa.     

胞外高分子物质对基质在复合生物膜内传质速率影响的测定

A model, for evaluating the effect of porosity and volume fraction of extracellular polymeric substances (EPS) within multispecies biofilms on the effective diffusivity, is developed and experimentally validated, based on the extraction of EPS from intact biofilms. The amount of EPS in biofilms significantly affects the effective diffusivity. For biofilms with porosity of 77%—95% in the top layers and 54%—58% in the bottom layers, the value of De/Dw decreases from 0.52—0.83 in the top layers to 0.23—0.31 in the bottom layers. Generally, the effective diffusivity in the heterotrophic/autotrophic biofilms is slightly lower than that in the heterotrophic biofilms, due to the lower porosity in the heterotrophic/autotrophic biofilms.     

超临界二氧化碳渗透聚丙烯成核剂的初步研究

Impregnation of isotactic polypropylene （iPP） with nucleating agent （NA21） using supercritical carbon dioxide as the swelling agent at different temperature and pressure and its non-isothermal crystallization kinetics were investigated. The results showed that NA21 was dispersed at a nanometer-scale in the PP matrix, resulting in the formation of different types .of crystal phases of iPP and the enhancement of its mechanical properties.     

丙酸盐影响利迪链霉菌AS 4.2501生产利迪链菌素及其碳流分布

To achieve higher antibiotic streptolydigin productivity through metabolic regulation, propionate was fed during the fermentation of Streptomyces lydicus AS 4.2501. The effects of propionate feeding on streptolydigin production and intracellular fluxes were investigated. The highest streptolydigin production yield of 95.10mg·L^-1 was obtained when 2mmol·L^-1 of sodium propionate was added at 60h of cultivation into shake-flask culture. This yield is 23.06% higher when compared to that of a batch culture without propionate supplementation. It was also found that when propionate was added, much more organic acids were excreted. Metabolic flux analysis was performed and it demonstrated that the carbon fluxes of the pentose phosphate pathway and the anaplerotic reaction were significantly increased after propionate feeding. The carbon flux from pyruvate to acetyl-CoA was determined to be 24.7, which was 12.27% higher than that in the batch culture. This study indicated that the glucose-6-phosphate and pyruvate nodes were potential bottlenecks for increasing streptolydigin productivity. Potential targets and strategies that could be manipulated through genetic and process engineering to increase the production of streptolydigin were also suggested.     

家用熔融碳酸盐燃料电池发电系统日常运行的遗传算法优化

To decrease the cost of electricity generation of a residential molten carbonate fuel cell （MCFC） power system, multi-crossover genetic algorithm （MCGA）, which is based on ＂multi-crossover＂ and ＂usefulness-based selection rule＂, is presented to minimize the daily fuel consumption of an experimental 10kW MCFC power system for residential application. Under the operating conditions obtained by MCGA, the operation constraints are satisfied and fuel consumption is minimized. Simulation and experimental results indicate that MCGA is efficient for the operation optimization of MCFC power systems.     

陶瓷膜乳化系统制备单分散乳状液的研究——集成式膜乳化反应器的前期研究

A new reactor with integrated conventional slurry stirred reactor and ceramic external membrane emulsification system, was introduced in this paper. Toluene and toluene containing surfactant was separately used as dispersed phase for preparation of emulsions. Two kinds of emulsions were prepared and compared. The volume average sizes of prepared emulsions were 3.53μm and 3.6μm respectively. The results showed that the droplet sizes of two kinds of emulsions were similar, but the monodispersed emulsion was only obtained with addition of surfactant into the dispersed phase.     

用大涡模拟结合改进的内外迭代法数值模拟搅拌槽中的液相流动

1 INTRODUCTION Stirred tank reactors are widely encountered in the chemical, pharmaceutical, and hydrometallurgical proc- esses. The fluid motion in stirred tanks is three-dimensional, complex, and covers a wide range of spatial and temporal scales. In the area surrounding the impeller, the flow is highly turbulent and swirling. The numerical simulation of such reactor systems is helpful in quantifying the effects of the impeller type, geometry, and the operational conditions in order to …     

二茂铁四氟硼酸盐用作潜热阳离子引发剂对环氧树脂的热固化引发环氧化合物阳离子热聚合

A novel latent thermal initiator, ferricenium tetrafluoroborate salt (FcBF4), for cationic polymerization of epoxides is reported. The activities of FcBF4 for different epoxides, including bisphenol-A-type epoxy oligomer E44, cycloaliphatic epoxy ERL4221, and glycidylether epoxy GGE, were evaluated by differential scanning calorimetry (DSC). The results showed a moderate thermal initiation activity for E44 and GGE at 78℃ and 108℃ respectively. When adding GGE to E44, the reaction was enhanced. The temperature of thermal degradation of the cured specimens for the system of E44/FcBF4, E44 10%GGE/FcBF4 and E44 10%ERL4221/FcBF4 is higher than 350℃.     

染料残渣焚烧过程中微量元素的形态转化及其迁移分配的预测

The release of heavy metals from the combustion of hazardous wastes is an environmental issue of increasing concern. The species transformation characteristics of toxic heavy metals and their distribution are considered to be a complex problem of mechanism. The behavior of hazardous dyestuff residue is investigated in a tubular furnace under the general condition of hazardous waste pyrolysis and gasfication. Data interpretation has been aided by parallel theoretical study based on a thermodynamic equilibrium model based on the principle of Gibbs free energy minimization. The results show that Ni, Zn, Mn, and Cr are more enriched in dyestuff residue incineration than other heavy metals （Hg, As, and Se） subjected to volatilization. The thermodynamic model calculation is used for explaining the experiment data at 800℃ and analyzing species transformation of heavy metals. These results of species transformation are used to predict the distribution and emission characteristics of trace elements. Although most trace element predictions are validated by the measurements, cautions are in order due to the complexity of incineration systems.     

在不分隔的反应器中原位电生成活性氯氧化降解蒽醌染料

The purpose of this paper was to investigate the possibility of treating C. I. Reactive Blue 19 wastewater by electrochemical oxidation via electrogenerated active chlorine, using metallic oxide coatings （dimensional stable anode, DSA） as anode. The electrolysis for the simulated wastewater was conducted at a constant current. Absorbances at 592 nm and 255 nm were measured to follow the decolorization of the dye and the degradatin of its aromatic ring. After 4 h of electrolysis under the experimental conditions： current density of 15 A·m^-2, 0.2 mol·L^-1 NaCl, 0.1 mol·L^-1 Na2SO4, 0.1 mmol·L^-1 dye, initial pH=6.4 and T=30℃, 100% decolorization of the dye and about 45% degradation of its aromatic ring were achieved, while no obvious change of total organic carbon was observed. The experimental results suggest that the decolorization of the dye and degradation of its aromatic ring were directly affected by current density, temperature, concentrations of the dye and sodium chloride, while slightly affected by initial pH and sodium sulfate concentration; the decolorization of the dye and degradation of its aromatic ring followed pseudo-first-order kinetics; and indirect electrooxidation, using electrogenerated active chlorine, predominated in the electrochemical oxidation.     

热致相分离法iPP中空纤维微空膜结构与性能--稀释剂的作用

Isotactic polypropylene （iPP） hollow fiber microporous membranes were prepared using thermally induced phase separation （TIPS） method. Di-n-butyl phthalate （DBP）, dioctyl phthalate （DOP）, and the mixed solvent were used as diluents. The effect of α （DOP mass fraction in diluent） on the morphology and performance of the hollow fiber was investigated. With increasing α, the morphology of the resulting hollow fiber changes from typical cellular structure to mixed structure, and then to typical particulate structure. As a result, the permeability of the hollow fiber increases sharply, and the mechanical properties of the hollow fiber decrease obviously. It is suggested that the morphology and performances of iPP hollow fiber microporous membrane can be controlled via adjusting the compatibility between iPP and diluent.     

一种通过重组大肠杆菌和重组恶臭假单胞菌生产3-羟基癸酸的新方法

3-hydroxydecanoic acid (3HD) is an interesting intermediate for chemical synthesis of many valuable compounds. A novel method to produce 3HD by recombinant bacteria was constructed in Escherichia coli HB101 and Pseudomonas putida GPp104, respectively. Simultaneous expression of both phaG encoding (R)-3-hydroxydecanoyl-ACP:CoA transacylase and tesB encoding thioesterase Ⅱ in E. coli HB101 increased 3HD production approximate 1.7-folds compared with the expression of phaG gene alone under identical conditions. In addition, when the tesB gene was introduced into the strain, the polyhydroxyalkanoate synthase negative strain P. putida GPpl04 produced extracellular 3HD. Thus, a novel pathway to produce 3HD by recombinant Pseudomonas was constructed. It was also found that the ratio of carbon source to nitrogen source affected the production of 3HD by recombinant P.putida harboring tesB gene. Nitrogen limitation seemed to promote the extracellular 3HD production.     

使用加热空气的预混天然气催化燃烧的实验研究

In this paper the premixed catalytic combustion emissions such as CO, unburned hydrocarbon （UHC）, NOx and the temperature distribution in the catalytic monolith with ultra low concentration of Pd were studied. Three types of monoliths were used for experiments and the temperature of preheated air was respectively 50℃, 100℃ and 200℃. The results showed that preheated air made radial temperature in the catalytic monolith uniform which helped to avoid local hot spots so as to decrease NOx emission. The experiment also proved that the shorter monolith showed much better catalytic combustion performance than longer one and the temperature at the exit of the shorter monolith was relatively lower. On the contrary, the temperature was higher in the longer monolith and the lethal NOx emission was slightly increased.     

用改进的Tait方程关联烷烃、芳香烃和乙醇在高压下的黏度

A new model was proposed to calculate the viscosity of fluids under the pressure ranging from 0.1 to 110MPa by improving the Tait equation, in which the viscosity μ of liquids was linked with activation volume V. The model with two adjustable parameters a and fl was applied in calculating viscosities for alkane, aromatic and alcohol family at high pressure. Results show that calculated values of viscosity are in good agreement with the experimental ones, and the average relative deviations for alkanes, aromatics and alcohols are 0.56%, 0.31% and 0.66%, respectively. Besides, the errors correlated by the model proposed in this paper were equivalent to the ones from the pure empirical Tait equation, and obviously superior to those from Eyring equation.     

偶联阳离子表面活性剂和常用阴离子表面活性剂混合溶液的相分离和微观结构

The properties of aqueous two-phase system (ATPS) of mixed solution containing gemini cationic surfactant trimethylene-l,3-bis(dodecyldimethyl ammonium) bromide (12-3-12, 2Br-) and traditional anionic surfactant sodium dodecyl sulfate (SDS) with or without added salt have been studied. An ATPS is formed in a narrow region of the ternary phase diagram different from that of traditional aqueous cationic-anionic surfactant systems. In ATPS region, the lowest total concentration of surfactants varies with the mixing ratio of geminis to SDS. Photographs obtained from freeze-etching, negative-staining and transmission electron microscopy show that the microstructures of two phases are different from each other. Micelles and vesicles can coexist in a single phase. The addition of salts can change the phase diagram of ATPS. Furthermore, the added salts promote the aggregation of rod-like micelles to form coarse network structure that increase the viscosity of solutions. The negative ions of the added salts are the determining factor.     

合成气制二甲醚三相淤浆床反应器的数学模型研究

A mathematical model for a bubble column slurry reactor is presented for dimethyl ether synthesis from syngas. Methanol synthesis from carbon monoxide and carbon dioxide by hydrogenation and the methanol dehydration are considered as independent reactions, in which methanol, dimethyl ether and carbon dioxide are the key components. In this model, the gas phase is considered to be in plug flow and the liquid phase to be in partly back mixing with axial distribution of solid catalyst. The simulation results show that the axial dispersion of solid catalysts, the operational height of the slurry phase in the bubble column slurry reactor, and the reaction results are influenced by the reaction temperature and pressure, which are the basic data for the scale-up of reactor.     

剪切力影响药用蘑菇灵芝的细胞生长和代谢物生产

By investigating the shear effect on submerged cultivation of a traditional Chinese medicinal herb Ganoderma lucidum, a relatively high cell concentration of 13.8 g·L-1 by dry mass was obtained in bioreactor at an impeller tip speed (ITS) of 0.51m·s-1. At an ITS of 0.51,1.02 and 1.53m·s-1, a maximal production titer of intracellular polysaccharide was 2.64, 2.20 and 2.28g·L-1 and that of ganoderic acid was 306, 299 and 273g·L-1, respectively. Under these ITSs, the maximal mean projected area of dispersed hyphae was 3.70, 2.54 and 2.13×104μm2, and that of pellets was 0.91, 0.67 and 0.55mm2, respectively. The information obtained is useful for efficient submerged cultivation of mushrooms on a large scale.     

脂肪酶促乌桕脂组分甘油解及其反应机理研究

Glycerolysis of Chinese vegetable tallow （CVT） fraction was investigated using a 1,3-specific lipase from Rhizopus arrhizus as catalyst. Based upon a binary gradient HPLC with an evaporative light-scattering detector （ELSD）, the contents of free fatty acids （FFA）, monoglycerides （MG）, diglycerides（DG） and triglycerides （TG） with their positional isomers during the glycerolysis were determined. The effects of water content and the ratio of glycerol to oil on the product distribution of glycerolysis were studied. Under the optimum reactant conditions： 250 units lipase per gram oil at 37℃ with 1：2 molar ratio of oil to glycerol in a solvent-free system, after 24 h reaction, the product consisted of 7.2% TG, 25.6% MG, 56.1% DG and 4.9% FFA （all by mass）. Furthermore, the mechanism of glycerolysis was discussed in detail.     

基于变长度移动窗口和HMM的工业过程故障在线诊断

An integrated framework is presented to represent and classify process data for on-line identifying abnormal operating conditions. It is based on pattern recognition principles and consists of a feature extraction step, by which wavelet transform and principal component analysis are used to capture the inherent characteristics from process measurements, followed by a similarity assessment step using hidden Markov model (HMM) for pattern comparison. In most previous cases, a fixed-length moving window was employed to track dynamic data, and often failed to capture enough information for each fault and sometimes even deteriorated the diagnostic performance. A variable moving window, the length of which is modified with time, is introduced in this paper and case studies on the Tennessee Eastman process illustrate the potential of the proposed method.