小尺寸栅极HEMT器件结温测量

用现有的红外法测量的GaN基HEMT器件结温,比实际最高温度点的温度低.而用喇曼法测量结温对设备要求高且不易于操作.针对现有技术对GaN基HEMT器件结温的测量存在一定困难的问题,设计了一款HEMT器件匹配电路.利用红外热像仪测量HEMT器件的结温升高,并结合物理数值模拟仿真,提出一种小尺寸栅极结温升高测量方法.结果表明,建立正确的仿真模型,可以得到不同栅极长度范围内的温度.通过这种方法可以测量出更接近实际的结温,为之后研究加载功率与壳温对AlGaN/GaN HEMT器件热阻的影响奠定了理论基础,并且为实际工作中热特性研究提供了参考依据.     

用紫外热反射热成像测量ＧａＮ ＨＥＭＴ的峰值温度

通过搭建一套以紫外LED作为光源的热反射热成像测温装置,对SiC衬底上的AlGaN/GaN 高电子迁移率晶体管 (HEMT) 的沟道GaN材料的峰值温度进行了测量。搭建了一套以365nm浅紫外LED为光源的热反射成像测温装置。采用清晰度算法和纳米量级三轴压电位移台实现对被测件的实时重聚焦。该装置具备400nm的空间分辨率,被用于测量被测件GaN材料的峰值温度。利用清晰度算法和测量过程中被测件漏源电压固定在28V,漏源电流以100mA为步进从200mA变化至500mA。具备2.8μm空间分辨率的显微红外热像仪被用于进行对比试验。随着漏源电流的上升,紫外热反射热成像测温结果比显微红外热成像测温结果高10.0℃~31.5℃不等。紫外热反射热成像技术较优的空间分辨率和景深指标使其能够更准确的测量GaN HEMT器件的峰值温度。     

AlGaN/GaN高电子迁移率晶体管的可靠性

利用正向肖特基结结电压与温度的线性关系,对AlGaN/GaN HEMT器件有源区瞬态温升进行了测量,其热阻为19.6℃/W。比较了不同测温方法和外界环境对器件沟道温升的影响。并研究了栅极施加反向直流阶梯应力对AlGaN/GaN HEMT器件性能的影响,结果表明器件在应力作用下电学参数退化,大信号寄生源/漏极电阻RS/RD和栅源正向I-V特性在击穿后能得到恢复。AlGaN势垒层陷阱俘获电子和电子填充栅极表面态是器件参数退化的原因,表面态恢复是器件参数恢复的主要原因。     

AlN阻挡层对AlGaN/GaNHEMT器件的影响

利用低压MOCVD技术在蓝宝石衬底上生长了AlGaN/GaN异质结和AlGaN/AlN/GaN异质结二维电子气材料,采用相同器件工艺制造出了AlGaN/GaN HEMT器件和AlGaN/AlN/GaN HEMT器件.通过对两种不同器件的比较和讨论,研究了AlN阻挡层的增加对AlGaN/GaN HEMT器件性能的影响.     

一种考虑自热效应的AlGaN/GaN HEMT大信号模型

当AlGaN/GaN HEMT输出高功率密度时,器件沟道温度的升高将引起电流的下降(自热效应).提出了一种针对AlGaN/GaN HEMT改进的大信号等效电路模型,考虑了HEMT自热效应,建立了一种改进的大信号I-V特性模型,仿真结果与测试结果符合较好,提高了大信号模型的精度.     

AlN阻挡层对AlGaN/GaN HEMT器件的影响

利用低压MOCVD技术在蓝宝石衬底上生长了AlGaN/GaN异质结和AlGaN/AlN/GaN异质结二维电子气材料,采用相同器件工艺制造出了AlGaN/GaN HEMT器件和AlGaN/AlN/GaN HEMT器件.通过对两种不同器件的比较和讨论,研究了AlN阻挡层的增加对AlGaN/GaN HEMT器件性能的影响.     

场板结构对AlGaN/GaN HEMT温度场的影响北大核心CSCD

用Silvaco的ATLAS软件仿真研究了场板结构对AlGaN/GaN高电子迁移率晶体管(HEMT)的温度场分布的影响,分析了场板结构影响器件温度场分布的可能因素。模拟结果表明,加入场板结构后,器件沟道二维电子气浓度减小,电场分布发生变化,器件栅极漏侧边缘处的沟道峰值温度降低。加入栅场板和源场板结构后,场板边缘处都有一个新的温度峰值出现,器件的沟道温度峰值在加入单层和双层栅场板及源场板后由511K分别下降到487、468和484K,这种降低作用会随着栅场板层数的增加而有所增强。仿真结果说明场板结构通过改变AlGaN/GaN HEMT器件沟道载流子浓度和电场分布,影响器件内部的温度场分布。优化器件的场板结构是提高AlGaN/GaN HEMT的可靠性有效途径之一。     

氧等离子体处理对薄势垒增强型AlGaN/GaN HEMT的影响

提出了一种利用薄势垒结构制造增强型AlGaN/GaN HEMT的方法。研究了SiN钝化对薄势垒AlGaN/GaN异质结的影响,并利用其控制沟道中的二维电子气密度。具有10nm SiN介质插入层欧姆接触在800℃下退火可以得到较好的接触性能。栅极区域中的SiN被刻蚀,以耗尽下面的二维电子气,从而使薄势垒AlGaN/GaN HEMT实现增强特性,其阈值电压为50 mV。对介质刻蚀后暴露的AlGaN表面进行氧等离子体处理,与未经处理的器件作对比,发现阈值电压提升到0.5V,栅漏电降低了一个数量级,击穿特性得到改善,但是最大饱和电流密度降低了。     

复合沟道氟离子增强型AlGaN/GaN HEMT的研究

提出一种复合沟道氟离子(F-)增强型AlGaN/GaN HEMT(Hybrid-channel enhancement-mode AlGaN/GaN HEMT,HCE-HEMT)新结构。该结构引入高、低浓度F-复合沟道,其中高浓度F-注入区位于沟道靠近源漏两端以调制阈值电压,获得增强型器件;低浓度F-区位于沟道中部以调制肖特基栅电极的正向开启电压,增加器件承受的栅电压摆幅,但它对其下方二维电子气的耗尽作用很弱。同时,高浓度区只占栅长的40%,减轻高浓度F-对沟道的影响,提升器件的电流能力。利用Sentaurus软件仿真,结果显示,与传统F-增强型AlGaN/GaN HEMT相比,HCE-HEMT载流能力提高了40.3%,比导通电阻下降了23.3%,同时反向耐压仅下降了5.3%。     

Ka波段AlGaN/GaN HEMT的研制

为了提高AlGaN/GaN HEMT的频率,采用了缩小源漏间距、优化栅结构和外围结构等措施设计了器件结构,并基于国内的GaN外延片和工艺完成了器件制备.测试表明所研制的AlGaN/GaN HEMT可以满足Ka波段应用.其中2×75μm栅宽AlGaN/GaN HEMT在30V漏压下的截止频率为32GHz,最大振荡频率为1...     

Curved crystal spectrometer for the measurement of X-ray lines from laser-produced plasmas

In order to diagnose the laser-produced plasmas, a focusing curved crystal spectrometer has been developed for measuring the X-ray lines radiated from a laser-produced plasmas. The design is based on the fact that the ray emitted from a source located at one focus of an ellipse will converge on the other focus by the reflection of the elliptical surface. The focal length and the eccentricity of the ellipse are 1350 mm and 0.9586, respectively. The spectrometer can be used to measure the X- ray lines in the wavelength range of 0.2-0.37 nm, and a LiF crystal （200） （2d = 0.4027 nm） is used as dispersive element covering Bragg angle from 30° to 67.5°. The spectrometer was tested on Shengnang- Ⅱ which can deliver laser energy of 60-80 J/pulse and the laser wavelength is 0.35 μm. Photographs of spectra including the 1 s2p ^1P1-1s^2 ^1S0 resonance line（w）, the 1s2p ^3P2-1s^2 1S0 magnetic quadrupole line（x）, the 1s2p ^3P1-1 s^2 ^1S0 intercombination lines（y）, the 1 s2p ^3S~1-1 s^2 ^1S0 forbidden line（z） in helium-like Ti Ⅹ Ⅺ and the 1 s2s2p ^2P3/2-1 s622s ^2S1/2 line（q） in lithium-like Ti Ⅹ Ⅹhave been recorded with a X-ray CCD camera. The experimental result shows that the wavelength resolution（λ/△ 2） is above 1000 and the elliptical crystal spectrometer is suitable for X-ray spectroscopy.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.     

Electronic Structure of Semiconductor Nanocrystals

This paper reviews our recent development of the use of the large-scale pseudopotential method to calculate the electronic structure of semiconductor nanocrystals, such as quantum dots and wires, which often contain tens of thousands of atoms. The calculated size-dependent exciton energies and absorption spectra of quantum dots and wires are in good agreement with experiments. We show that the electronic structure of a nanocrystal can be tuned not only by its size,but also by its shape. Finally,we show that defect properties in quantum dots can be significantly different from those in bulk semiconductors.     

Critical Stage Rule-Based Real Time Dispatch（RTD）System in Highly-Mixed-Products （HMP） FAB

An improving utilization and efficiency of critical equipments in semiconductor wafer fabrication facilities are concerned. Semiconductor manufacturing FAB is one of the most complicated and cost sensitive environments. A good dispatching tool will make big difference in equipment utilization and FAB output as a whole. The equipment in this paper is In-Line DUV Scanner. There are many factors impacting utilization and output on this equipment group. In HMP environment one of the issues is changing of reticule in this area and idle counts due to load unbalance between equipments. Here we'll introduce a rule-based RTD system which aiming at decreasing the number of recipe change and idle counts among a group of scanner equipment in a high-mixed-products FAB.     

GaAsSb/InAlAs PA DHBTs Grown by Production MBE

The epi material growth of GaAsSb based DHBTs with InAlAs emitters are investigated using a 4 × 100mm multi-wafer production Riber 49 MBE reactor fully equipped with real-time in-situ sensors including an absorption band edge spectroscope and an optical-based flux monitor. The state-of-the-art hole mobilities are obtained from 100nm thick carbon-doped GaAsSb. A Sb composition variation of less than ± 0.1 atomic percent across a 4 × 100mm platen configuration has been achieved. The large area InAlAs/GaAsSb/InP DHBT device demonstrates excellent DC characteristics,such as BVCEO＞6V and a DC current gain of 45 at 1kA/cm2 for an emitter size of 50μm × 50μm. The devices have a 40nm thick GaAsSb base with p-doping of 4. 5 × 1019cm-3 . Devices with an emitter size of 4μm × 30μm have a current gain variation less than 2% across the fully processed 100mm wafer. ft and fmax are over 50GHz,with a power efficiency of 50% ,which are comparable to standard power GaAs HBT results. These results demonstrate the potential application of GaAsSb/InP DHBT for power amplifiers and the feasibility of multi-wafer MBE for mass production of GaAsSb-based HBTs.     

Influence of polarization extinction ratio on distributed polarization coupling detection

Distributed polarization coupling in polarization-maintaining fibers can be detected by using a white light Michelson interferometer. This technique usually requires that only one polarization mode is excited. However, in practical measurement, the injection polarization direction could not be exactly aligned to one of the principal axes of the PMF, so the influence of the polarization extinction ratio should be considered. Based on the polarization coupling theory, the influence of the incident polarization extinction on the measurement result is evaluated and analyzed, and a method for distributed polarization coupling detection is developed when both two orthogonal eigenmodes are excited.     

Noise character analysis and the restraint of self-pulsation laser diodes

We calculate the Langevin noise sources of self-pulsation laser diodes, analyze the effects of active region noise and saturable-absorption region noise on the power fluctuation as well as period fluctuation, and propose a novel method to restrain the noise effects. A visible SIMULINK model is established to simulate the system, The results indicate that the effects of noise in absorption region can be ignored; that with the increase of DC injecting current, the noise effects enhance power jitter, and nevertheless, the period jitter is decreased; and that with external sinusoidal current modulating the self-pulsation laser diode, the noise-induced power jitter and period jitter can be suppressed greatly. This work is valuable for clock recovery in all-optical network.     

High-quality single-crystal CdSe nanoribbons and their optical properties

Large-scale synthesis of single-crystal CdSe nanoribbons is achieved by a modified thermal evaporation method, in which two-step-thermal-evaporation is used to control CdSe sources＇ evaporation. The synthesized CdSe nanoribbons are usually several micrometers in width, 50 nm in thickness, and tens to several hundred micrometers in length. Studies have shown that high-quality CdSe nanoribbons with regular shapes can be obtained by this method. Room-temperature photolumines-cence indicates that the lasing emission at 710 nm has been observed under optical pumping （266 nm） at power densities of 25-153 kW/cm^2. The full width half maximum （FWHM） of the lasing mode is 0.67 nm     

Propagation of hermite-cosh-gaussian beams passing through ABCD optical system with an annular aperture

By using the expansion of the aperture function into a finte sum of complex Gaussian functions, the corresponding analytical expressions of Hermite-cosh-Gaussian beams passing through annular apertured paraxially and symmetrically optical systems written in terms of ABCD matrix were derived, and they could reduce to the cases with squared aperture. In a similar way, the corresponding analytical expressions of cosh-Gaussian beams through annular apertured ABCD matrix were also given. The method could save more calculation time than that by using the diffraction integral formula directly.     

中国建立EB级存储实验室,致力云计算应用(英文)

正With the support of 863 programs,Sugon Information Industry Co.,Ltd.,set up a dawning EB-class storage laboratory to address massive data storage requirements and largescale cloud computing demonstration applications.The Dawning EB-class cloud storage system adopts advanced fault-tolerant architecture,efficient data fault-tolerant algorithms with user authentication and data encryption policies to deal with the"lost""wrong"and"stolen"problems of data for ensuring the reliability and safety of the EB-class storage system in the public network application environments.The Dawning EB-class Storage Laboratory taking advan-