ft =203GHz的超高速InP/InGaAs双异质结晶体管

为了适应数字及模拟电路带宽的不断增加,我们在传统的台面结构基础上利用BCB钝化平坦化工艺技术,设计并研制了InP/InGaAs/InP双异质结双极型晶体管。我们研制的晶体管ft达到203GHz,是目前国内InP基DHBT的最高水平,发射极尺寸为1.0μm×20μm,电流增益β为166,击穿电压为4.34V,我们的器件采用了40nm高掺杂InGaAs基区,以及203nm含有InGaAsP复合式结构的集电区。该器件非常适合高速中功耗方面的应用。     

In0.53Ga0.47As/InP高速光电二极管材料生长及光电性能

利用低压MOCVD技术制备PIN结构的InP基InGaAs外延材料。采用分层吸收渐变电荷倍增(SAGCM)结构,通过两次Zn扩散、多层介质膜淀积、Au/Zn p型欧姆接触、Au/Ge/Ni n型欧姆接触等标准半导体平面工艺,设计制造正入射平面In_(0.53)Ga_(0.47)As/InP雪崩光电二极管器件。该器件采用与InP衬底晶格匹配的In_(0.53)Ga_(0.47)As材料做吸收层,InP材料做倍增层,同时引入InGaAsP梯度层。探测器件光敏面直径50μm,器件测试结果表明该器件光响应特性正常,击穿电压约43 V,在低于击穿电压3 V左右可以得到大约10 A/W的光响应度,在0 V到小于击穿电压1 V的偏压范围内,暗电流只有1 nA左右。光电二极管在8 GHz以下有平坦的增益,适用于5 Gbit/s光通信系统。     

用于单片集成光接收机前端的GaAs基InP/InGaAs HBT

实现了一种可用于单片集成光接收机前端的GaAs基InP/InGaAs HBT。借助超薄低温InP缓冲层在GaAs衬底上生长出了高质量的InP外延层。在此基础上,只利用超薄低温InP缓冲层技术就在半绝缘GaAs衬底上成功制备出了InP/InGaAsHBT,器件的电流截止频率达到4.4GHz,开启电压0.4V,反向击穿电压大于4V,直流放大倍数约为20。该HBT器件和GaAs基长波长、可调谐InP光探测器单片集成为实现适用于WDM光纤通信系统的高性能、集成化光接收机前端提供了一种新的解决方法。     

基于零偏置肖特基二极管的270 GHz高性能波导检波器

根据InP二极管的物理结构, 采用三维高频电磁仿真软件对其精确建模仿真, 获得二极管的物理模型和匹配电路的精确参数, 而后将此模型利用谐波平衡进行仿真设计.最后, 在此基础上采用InP肖特基二极管, 设计制作并测试了国内首款270GHz的零偏置检波器.检波器的最大电压响应度为1600V/W, 在260~280GHz范围内, 电压响应的典型值为1400V/W, 其对应的等效噪声功率典型值为18pW/Hz.实验结果与仿真结果比较吻合, 其结果表明, 设计方法较为精确, 具有设计简单、优化方便等优点.     

一种高性能InP基谐振隧穿二极管的研制

设计并用分子束外延技术生长了InP基InGaAs/AlAs体系RTD材料,采用传统湿法腐蚀、光学接触式光刻、金属剥离、台面隔离和空气桥互连工艺,研制出了具有优良负阻特性和较高阻性截止频率的InP基RTD单管，器件正向PVCR为17.5,反向PVCR为28,峰值电流密度为56kA/cm^2,采用RNC电路模型进行数据拟合后得到阻性截止频率为82.8GHz，实验为今后更高性能RTD单管的研制,以及RTD与其他高速高频三端器件单片集成电路的设计与研制奠定了基础。     

基于零偏置肖特基二极管的270GHz高性能波导检波器（英文）

根据InP二极管的物理结构,采用三维高频电磁仿真软件对其精确建模仿真,获得二极管的物理模型和匹配电路的精确参数,而后将此模型利用谐波平衡进行仿真设计.最后,在此基础上采用InP肖特基二极管,设计制作并测试了国内首款270 GHz的零偏置检波器.检波器的最大电压响应度为1600 V/W,在260~280 GHz范围内,电压响应的典型值为1400 V/W,其对应的等效噪声功率典型值为18 pW/槡Hz.实验结果与仿真结果比较吻合,其结果表明,设计方法较为精确,具有设计简单、优化方便等优点.     

一种高性能InP基谐振隧穿二极管的研制

设计并用分子束外延技术生长了InP基InGaAs/AlAs体系RTD材料,采用传统湿法腐蚀、光学接触式光刻、金属剥离、台面隔离和空气桥互连工艺,研制出了具有优良负阻特性和较高阻性截止频率的InP基RTD单管.器件正向PVCR为17.5,反向PVCR为28,峰值电流密度为56kA/cm2,采用RNC电路模型进行数据拟合后得到阻性截止频率为82.8GHz.实验为今后更高性能RTD单管的研制,以及RTD与其他高速高频三端器件单片集成电路的设计与研制奠定了基础.     

栅长90nm的晶格匹配InAlAs／InGaAs／InP HEMT

文章报道了90nm栅长的晶格匹配InP基HEMT器件。栅图形是通过80kV的电子束直写的,并采用了优化的三层胶工艺。器件做在匹配的InAlAs／InGaAs／InP HEMT材料上。当Vds=1．0V时,两指75μm栅宽器件的本征峰值跨导达到720ms／mm,最大电流密度为500mA／mm,器件的阂值电压为．0．8V,截止频率达到127GHz,最大振荡频率达到152GHz。     

220GHz低噪声放大器研究

基于IHP锗硅BiCMOS工艺,研究和实现了两种220 GHz低噪声放大器电路,并将其应用于220 GHz太赫兹无线高速通信收发机电路。一种是220 GHz四级单端共基极低噪声放大电路,每级电路采用了共基极（Common Base, CB）电路结构,利用传输线和金属-绝缘体-金属(Metal-Insulator-Metal, MIM)电容等无源电路元器件构成输入、输出和级间匹配网络。该低噪放电源的电压为1.8 V,功耗为25 mW,在220 GHz频点处实现了16 dB的增益,3 dB带宽达到了27 GHz。另一种是220 GHz四级共射共基差分低噪声放大电路,每级都采用共射共基的电路结构,放大器利用微带传输线和MIM电容构成每级的负载、Marchand-Balun、输入、输出和级间匹配网络等。该低噪放电源的电压为3 V,功耗为234 mW,在224 GHz频点实现了22 dB的增益,3 dB带宽超过6 GHz。这两个低噪声放大器可应用于220 GHz太赫兹无线高速通信收发机电路。     

高速InP/InGaAs雪崩光电二极管

采用分层吸收渐变电荷倍增(SAGCM)结构,通过两次扩散、多层介质淀积、AuZn p型欧姆接触、AuGeNi n型欧姆接触等工艺,设计制造了正面入射平面InP/InGaAs雪崩光电二极管,器件利用InGaAs做吸收层,InP做增益层,光敏面直径50 μm;测试结果表明器件有正常的光响应特性,击穿电压32～42 V,在低于击穿电压2 V左右可以得到大约10A/W的光响应度,在0到小于击穿电压1 V的偏压范围内,暗电流只有1 nA左右;器件在2.7 GHz以下有平坦的增益.     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.