OCDMA频域/时域的新型线性组合编码

提出了一种适合于光码多分址(OCDMA)频域／时域(λ-t)的二维线性组合码(LCC)新的构造方法,设计了编／解码方案,分析了系统性能。研究表明：影响LCC性能的参数主要有其子码字数和码字中相同子码字的个数。随着LCC的子码数的增加,OCDMA系统的用户容量显著提高;通过改变LCC的设计参数,系统的误码率(BER)得到改进,当LCC的子码字数确定时,BER随系统中LCC码字中相同子码字的个数的最大值的增加而劣化;当LCC码字中相同子码字的个数的最大值一定时,BER随LCC的子码字数的增加而得到改进。     

基于改进LSOOC的SAC-OCDMA通信系统性能分析

提出了一种基于改进的latin方阵光正交码(MLSOOC)、适合光谱幅度编码(SAC)光码分多址(OCDMA)系统的地址码构造方法,码字间有理想的互相关,容量达到了SAC的上限.分析了SAC编解码的原理、光纤Bragg光栅(FBGs)谱幅编解码的工作过程及在考虑相位引起的强度噪声(PIIN)、热噪声和散弹噪声情况下的系统信噪比(SNR)和误码率(BER).结果表明:在光源和信道理想条件下,多址干扰(MAI)可以消除;在考虑噪声的情况下,可以有效抑制PIIN减小BER;在满足一定BER下,系统承载的同步上路用户多容量比用Hadamard码大大增加.     

一种基于素数码和单重合序列的二维光正交码

以素数码(PC)作为时间扩频伪随机序列,以单重合序列(OCS)作为波长跳频伪随机序列,构造了一种新的二维光正交码(OOC)PC/OCS,并分析了码字的互相关性能.与素数跳频码PC/PC相比,PC/OCS的波长数并不局限于素数,可以是任意整数,不仅构造灵活,而且可充分利用多波长光码分多址(MW OCDMA)系统的有效波长数.当系统的有效波长数为大于某个素数的整数时,PC/OCS不仅码字容量大于PC/PC,而且互相关性能也有所改善,降低了MW OCDMA系统的误码率(BER).     

基于超结构光纤光栅的混沌序列OCDMA系统

提出了一种双极性编解码的光码多分址(OCDMA)系统,采用混沌序列作地址码,并使用超结构光纤布拉格光栅(SSFBG)作编/解码器。三阶Chebyshev映射能够产生具有良好相关性且适用于异步CDMA系统的双极性混沌序列,通过对三阶Chebyshev映射赋予一定初值,并进行反复迭代,得到一定长度的双极性混沌序列。根据地址码的特征,通过控制FBG的折射率分布形成SSFBG,利用SSFBG产生相应的双极性混沌序列作OCDMA系统的编/解码器。对系统性能进行了定量分析,在完全异步的情况下,推导了信噪比(SNR)与误码率(BER)的表达式。仿真分析了系统在不同码长下的BER随接入用户数的变化,并和使用Gold序列的情况进行了比较。结果表明,随着码长的增加,在接入用户数一定的情况下,系统具有较低的BER;由于混沌序列良好的自互相关性,相应的混沌序列OCDMA系统与使用Gold序列的系统相比具有较低的BER,并可以容纳更多的用户数。     

异步相干扩时光码分多址系统的干扰性能分析

从码字的非周期互相关函数出发,分析异步相干扩时光码分多址(OCDMA)系统的多址干扰(MAI)和差拍噪声(BN).干扰用户不同的传输时延,非周期互相关强度均值随之变化,差拍噪声和多址干扰也随之变化.给出了差拍噪声和多址干扰与非周期互相关强度均值的关系,讨论了异步相干扩时OCDMA系统的误码率(BER)与非周期互相关强度均值的关系.最后,以码长511的Gold码为例,针对干扰用户之间不同的传输时延,得到了异步相干扩时OCDMA系统的误码率上界与平均误码率性能.在平均误码率情况下,OCDMA系统能支持12个干扰用户,而在最差情况下(误码率上界),系统容纳的干扰用户数不超过4个.     

采用光硬限幅器和RS码的多波长OCDMA性能分析

提出了一种采用多个光硬限幅器和RS信道编码的多波长光码多分址（MW OCDMA）系统,理论分析了其误码率和（BER）和归一化吞吐量性能.结果表明,采用光硬限幅器的MW OCDMA系统BER性能将明显改善,进一步采用RS信道编码后,MW OCDMA系统BER性能将大大改善.另一方面,采用光硬限幅器的MW OCDMA系统的归一化吞吐量明显提高,特别是归一化吞吐量峰值提高了约1倍,但进一步采用RS信道编码后,MW OCDMA系统的归一化吞吐量并没有提高,在系统负载量不是很大的情况下还略有下降.     

混沌多值序列用于光码分多址系统的性能分析

针对光码分多址(OCDMA)系统对地址码的要求,提出了一种利用3阶Chebyshev混沌多值序列编码的方案,给出了码字的生成方法;基于相移超结构光纤布拉格光栅(SSFBG)编/解码器,利用传输矩阵法仿真分析了系统相关特性与码字长度、量化级数的关系.结果表明,多值混沌序列用于OCDMA频谱相位编码是可行的.     

WDM/OCDMA混合系统中一种新型的接收机

文章针对波分复用/光码分多址(WDM/OCDMA)混合系统中存在窄带干扰(NBI)的问题,提出了一种新颖的用户接收机模型.从理论推导得知,该方案能完全滤除WDM用户间的NBI.同时,仿真结果也验证了系统的误码率(BER)有显著的降低,系统性能得到了改善,且归一化门限值为0.28时,BER最小.     

基于OOC的WDM+OCDMA系统性能研究

基于光正交码,研究了WDM+OCDMA系统的性能。采用4个波长信道和3个码字的光正交码OOC(37,4,1),对12个用户的WDMA+OCDMA进行了系统仿真,用户数据速率为1Gbit/s,单模光纤长为50km,色散补偿光纤长为5km。如需增加WDMA+OCDMA的用户数,可以通过增加波长信道数或码字容量来实现。分析了色散效应对WDMA+OCDMA系统性能的影响,研究了用户之间相对延时对多址干扰和系统性能的影响。     

基于STOOC的SAC-OCDMA系统地址码的性能分析

分析了STOOC码字的设计方案及码重、互相关性、系统容量等性能,仿真出几种适合SAC-OCDMA系统码字的多址干扰误码率与并发用户数的关系,结果表明:STOOC码字容量达到了SAC的上限;STOOC码字的编解码比其它几种码字更容易,且非常适合光谱幅度编码(SAC)光码分多址(OCDMA)系统;得出了在STOOC码字的系统多址干扰误码率比其他码字小,在一定误码率要求下,STOOC码字比其他码字可以承载更多的并发用户。     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Cost-effective test solutions for smart card and other integrated flash applications

From its emergence in the late 1980s as a lower cost alternative to early EEPROM technologies, flash memory has evolved to higher densities and speedsand rapidly growing acceptance in mobile applications.In the process, flash memory devices have placed increased test requirements on manufacturers. Today, as flash device test grows in importance in China, manufacturers face growing pressure for reduced cost-oftest, increased throughput and greater return on investment for test equipment. At the same time, the move to integrated flash packages for contactless smart card applications adds a significant further challenge to manufacturers seeking rapid, low-cost test.     

An improved parallel thinning algorithm with two subiterations

The parallel thinning algorithm with two subiterations is improved in this paper. By analyzing the notions of connected components and passes, a conclusion is drawn that the number of passes and the number of eight-connected components are equal. Then the expression of the number of eight-connected components is obtained which replaces the old one in the algorithm. And a reserving condition is proposed by experiments, which alleviates the excess deletion where a diagonal line and a beeline intersect. The experimental results demonstrate that the thinned curve is almost located in the middle of the original curve connectivelv with single pixel width and the processing speed is high.