Experimental and computational assessment of 1,4-Dioxane degradation in a photo-Fenton reactive ceramic membrane filtration process

• 1,4-Dioxane was degraded via the photo-Fenton reactive membrane filtration. • Degradation efficiency and AQY were both enhanced in photocatalytic membrane. • There is a tradeoff between photocatalytic degradation and membrane permeation flux. • Degradation pathways of 1,4-Dioxane is revealed by DFT analysis. The present study evaluated a photo-Fenton reactive membrane that achieved enhanced 1,4-Dioxane removal performance. As a common organic solvent and stabilizer, 1,4-Dioxane is widely used in a variety of industrial products and poses negative environmental and health impacts. The membrane was prepared by covalently coating photocatalyst of goethite (α-FeOOH) on a ceramic porous membrane as we reported previously. The effects of UV irradiation, H₂O₂ and catalyst on the removal efficiency of 1,4-Dioxane in batch reactors were first evaluated for optimized reaction conditions, followed by a systematical investigation of 1,4-Dioxane removal in the photo-Fenton membrane filtration mode. Under optimized conditions, the 1,4-Dioxane removal rate reached up to 16% with combination of 2 mmol/L H₂O₂ and UV₃₆₅ irradiation (2000 µW/cm²) when the feed water was filtered by the photo-Fenton reactive membrane at a hydraulic retention time of 6 min. The removal efficiency and apparent quantum yield (AQY) were both enhanced in the filtration compared to the batch mode of the same photo-Fenton reaction. Moreover, the proposed degradation pathways were analyzed by density functional theory (DFT) calculations, which provided a new insight into the degradation mechanisms of 1,4-Dioxane in photo-Fenton reactions on the functionalized ceramic membrane.     

Remediation of 2,4-dichlorophenol-contaminated groundwater using nano-sized CaO2 in a two-dimensional scale tank

• Nano CaO₂ is evaluated as a remediation agent for 2,4-DCP contaminated groundwater. • 2,4-DCP degradation mechanism by different Fe²⁺ concentration was proposed. • 2,4-DCP was not degraded in the system for solution pH>10. • The 2,4-DCP degradation area is inconsistent with the nano CaO₂ distribution area. This study evaluates the applicability of nano-sized calcium peroxide (CaO₂) as a source of H₂O₂ to remediate 2,4-dichlorophenol (2,4-DCP) contaminated groundwater via the advanced oxidation process (AOP). First, the effect and mechanism of 2,4-DCP degradation by CaO₂ at different Fe concentrations were studied (Fenton reaction). We found that at high Fe concentrations, 2,4-DCP almost completely degrades via primarily the oxidation of •OH within 5 h. At low Fe concentrations, the degradation rate of 2,4-DCP decreased rapidly. The main mechanism was the combined action of •OH and O₂^•−. Without Fe, the 2,4-DCP degradation reached 13.6% in 213 h, primarily via the heterogeneous reaction on the surface of CaO₂. Besides, 2,4-DCP degradation was significantly affected by solution pH. When the solution pH was>10, the degradation was almost completely inhibited. Thus, we adopted a two-dimensional water tank experiment to study the remediation efficiency CaO₂ on the water sample. We noticed that the degradation took place mainly in regions of pH<10 (i.e., CaO₂ distribution area), both upstream and downstream of the tank. After 28 days of treatment, the average 2,4-DCP degradation level was ≈36.5%. Given the inadequacy of the results, we recommend that groundwater remediation using nano CaO₂: (1) a buffer solution should be added to retard the rapid increase in pH, and (2) the nano CaO₂ should be injected copiously in batches to reduce CaO₂ deposition.     

Significant increase of assimilable organic carbon (AOC) levels in MBR effluents followed by coagulation,ozonation and combined treatments: Implications for biostability control of reclaimed water

• Annual AOCs in MBR effluents were stable with small increase in warmer seasons. • Significant increase in AOC levels of tertiary effluents were observed. • Coagulation in prior to ozonation can reduce AOC formation in tertiary treatment. • ∆UV₂₅₄ and SUVA can be surrogates to predict the AOC changes during ozonation. As water reuse development has increased, biological stability issues associated with reclaimed water have gained attention. This study evaluated assimilable organic carbon (AOC) in effluents from a full-scale membrane biological reactor (MBR) plant and found that they were generally stable over one year (125–216 µg/L), with slight increases in warmer seasons. After additional tertiary treatments, the largest increases in absolute and specific AOCs were detected during ozonation, followed by coagulation-ozonation and coagulation. Moreover, UV₂₅₄ absorbance is known to be an effective surrogate to predict the AOC changes during ozonation. Applying coagulation prior to ozonation of MBR effluents for removal of large molecules was found to reduce the AOC formation compared with ozonation treatment alone. Finally, the results revealed that attention should be paid to seasonal variations in influent and organic fraction changes during treatment to enable sustainable water reuse.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

A pulsed switching peroxi-coagulation process to control hydroxyl radical production and to enhance 2,4-Dichlorophenoxyacetic acid degradation

• A new pulsed switching peroxi-coagulation (PSPC) system was developed. • The EC_T for 2,4-D removal in the PSPC was lower than that in the EF. • The iron consumption for 2,4-D removal in the PSPC was lower than that in the PC. The aim of this study was to develop a new pulsed switching peroxi-coagulation system to control hydroxyl radical (?OH) production and to enhance 2,4-Dichlorophenoxyacetic acid (2,4-D) degradation. The system was constructed with a sacrifice iron anode, a Pt anode, and a gas diffusion cathode. Production of H₂O₂ and Fe²⁺ was controlled separately by time delayers with different pulsed switching frequencies. Under current densities of 5.0 mA/cm² (H₂O₂) and 0.5 mA/cm² (Fe²⁺), the ?OH production was optimized with the pulsed switching frequency of 1.0 s (H₂O₂):0.3 s (Fe²⁺) and the ratio of H₂O₂ to Fe²⁺ molar concentrations of 6.6. Under the optimal condition, 2,4-D with an initial concentration of 500 mg/L was completely removed in the system within 240 min. The energy consumption for the 2,4-D removal in the system was much lower than that in the electro-Fenton process (68±6 vs. 136±10 kWh/kg TOC). The iron consumption in the system was ~20 times as low as that in the peroxi-coagulation process (196±20 vs. 3940±400 mg/L) within 240 min. The system should be a promising peroxi-coagulation method for organic pollutants removal in wastewater.     

Pesticide wastewater treatment using the combination of the microbial electrolysis desalination and chemical-production cell and Fenton process

• MEDCC combined with Fenton process was developed to treat real pesticide wastewater. • Pesticide removal was attributable to desalination in the MEDCC. • High COD removal was attributable to organic distributions in different chambers. The combination of the microbial electrolysis desalination and chemical-production cell (MEDCC) and Fenton process for the pesticide wastewater treatment was investigate in this study. Real wastewater with several toxic pesticides, 1633 mg/L COD, and 200 in chromaticity was used for the investigation. Results showed that desalination in the desalination chamber of MEDCC reached 78%. Organics with low molecular weights in the desalination chamber could be removed from the desalination chamber, resulting in 28% and 23% of the total COD in the acid-production and cathode chambers, respectively. The desalination in the desalination chamber and organic transfer contributed to removal of pesticides (e.g., triadimefon), which could not be removed with other methods, and of the organics with low molecular weights. The COD in the effluent of the MEDCC combined the Fenton process was much lower than that in the perixo-coagulaiton process (<150 vs. 555 mg/L). The combined method consumed much less energy and acid for the pH adjustment than that the Fenton.     

Hydroxyl radical intensified Cu2O NPs/H2O2 process in ceramic membrane reactor for degradation on DMAc wastewater from polymeric membrane manufacturer

• Cu₂O NPs/H₂O₂ Fenton process was intensified by membrane dispersion. • DMAc removal was enhanced to 98% for initial DMAc of 14000 mg/L. • Analyzed time-resolved degradation pathway of DMAc under ·OH attack. High-concentration industrial wastewater containing N,N-dimethylacetamide (DMAc) from polymeric membrane manufacturer was degraded in Cu₂O NPs/H₂O₂ Fenton process. In the membrane-assisted Fenton process DMAc removal rate was up to 98% with 120 min which was increased by 23% over the batch reactor. It was found that ·OH quench time was extended by 20 min and the maximum ·OH productivity was notably 88.7% higher at 40 min. The degradation reaction rate constant was enhanced by 2.2 times with membrane dispersion (k = 0.0349 min⁻¹). DMAc initial concentration (C₀) and H₂O₂ flux (J_p) had major influence on mass transfer and kinetics, meanwhile, membrane pore size (r_p) and length (L_m) also affected the reaction rate. The intensified radical yield, fast mass transfer and nanoparticles high activity all contributed to improve pollutant degradation efficiency. Time-resolved DMAc degradation pathway was analyzed as hydroxylation, demethylation and oxidation leading to the final products of CO₂, H₂O and NO₃⁻ (rather than NH₃ from biodegradation). Continuous process was operated in the dual-membrane configuration with in situ reaction and separation. After five cycling tests, DMAc removal was all above 95% for the initial [DMAc]₀ = 14,000 mg/L in wastewater and stability of the catalyst and the membrane maintained well.     

Effects of oxidizing environment on digestate humification and identification of substances governing the dissolved organic matter (DOM) transformation process

• Liquid digestate humification was investigated under different oxidizing environment. • Tryptophan-like substances dominated the transformation of the liquid digestate DOM. • The humification sequence of the liquid digestate DOM was identified. • UV₃₂₅ was first identified as a pre-humus intermediate during humification reaction. The formation of humic-like acids (HLAs) is an essential process for converting liquid digestate into organic soil amendments to enhance agricultural sustainability. The aim of this study was to investigate the impact of oxygen and/or MnO₂ on the production of HLAs. Herein, abiotic humification performance of the digestate dissolved organic matter (DOM) is investigated with fluxes of air and N₂ in the absence and presence of MnO₂. Our results demonstrated that the fate of digestate DOM greatly depends on the oxidizing environment, the MnO₂ enhanced nitrogen involved in the formation of HLAs. The synergistic effects of MnO₂ and oxygen effectively improved the production of HLAs, and the corresponding component evolution was analyzed using spectroscopic evidence. The two-dimensional correlation spectroscopy results demonstrated that the reaction sequence of digestate DOM followed the order of protein-like substances, substances with an absorbance at 325 nm, substances with UV absorbance at 254 nm and HLAs. Additionally, excitation emission matrix fluorescence combined with parallel factor analysis (EEM-PARAFAC) showed that tryptophan-like C3 was more prone to transformation than tyrosine-like C2 and was responsible for the humification process. The substance with an absorbance at 325 nm was a reaction intermediate in the transformation process of protein-like substances to HLAs. The above findings can be used to promote the production of liquid fertilizer associated with carbon sequestration as well as the sustainable development of biogas production.     

Comparison of different valent iron on anaerobic sludge digestion: Focusing on oxidation reduction potential,dissolved organic nitrogen and microbial community

• ORP value from −278.71 to −379.80 mV showed indiscernible effects on methane yield. • Fe(II) and Fe(III) promoted more degradation of proteins and amino acids than Fe⁰. • The highest enrichment of Geobacter was noted in samples added with Fe⁰. • Cysteine was accumulated during iron enhanced anaerobic sludge digestion. • Both iron content and valence were important for methane production. This study compared effects of three different valent iron (Fe⁰, Fe(II) and Fe(III)) on enhanced anaerobic sludge digestion, focusing on the changes of oxidation reduction potential (ORP), dissolved organic nitrogen (DON), and microbial community. Under the same iron dose in range of 0−160 mg/L after an incubation period of 30 days (d), the maximum methane production rate of sludge samples dosed with respective Fe⁰, Fe(II) and Fe(III) at the same concentration showed indiscernible differences at each iron dose, regardless of the different iron valence. Moreover, their behavior in changes of ORP, DON and microbial community was different: (1) the addition of Fe⁰ made the ORP of sludge more negative, and the addition of Fe(II) and Fe(III) made the ORP of sludge less negative. However, whether being more or less negative, the changes of ORP may show unobservable effects on methane yield when it ranged from −278.71 to −379.80 mV; (2) the degradation of dissolved organic nitrogen, particularly proteins, was less efficient in sludge samples dosed with Fe⁰ compared with those dosed with Fe(II) and Fe(III) after an incubation period of 30 d. At the same dose of 160 mg/L iron, more cysteine was noted in sludge samples dosed with Fe(II) (30.74 mg/L) and Fe(III) (27.92 mg/L) compared with that dosed with Fe⁰ (21.75 mg/L); (3) Fe⁰ particularly promoted the enrichment of Geobacter, and it was 6 times higher than those in sludge samples dosed with Fe(II) and Fe(III) at the same dose of 160 mg/L iron.     

Enhancement of the electrocatalytic oxidation of antibiotic wastewater over the conductive black carbon-PbO2 electrode prepared using novel green approach

• A novel conductive carbon black modified lead dioxide electrode is synthesized. • The modified PbO₂ electrode exhibits enhanced electrochemical performances. • BBD method could predict optimal experiment conditions accurately and reliably. • The modified electrode possesses outstanding reusability and safety. The secondary pollution caused by modification of an electrode due to doping of harmful materials has long been a big concern. In this study, an environmentally friendly material, conductive carbon black, was adopted for modification of lead dioxide electrode (PbO₂). It was observed that the as-prepared conductive carbon black modified electrode (C-PbO₂) exhibited an enhanced electrocatalytical performance and more stable structure than a pristine PbO₂ electrode, and the removal efficiency of metronidazole (MNZ) and COD by a 1.0% C-PbO₂ electrode at optimal conditions was increased by 24.66% and 7.01%, respectively. Results revealed that the electrochemical degradation of MNZ wastewater followed pseudo-first-order kinetics. This intimates that the presence of conductive carbon black could improve the current efficiency, promote the generation of hydroxyl radicals, and accelerate the removal of MNZ through oxidation. In addition, MNZ degradation pathways through a C-PbO₂ electrode were proposed based on the identified intermediates. To promote the electrode to treat antibiotic wastewater, optimal experimental conditions were predicted through the Box-Behnken design (BBD) method. The results of this study suggest that a C-PbO₂ electrode may represent a promising functional material to pretreat antibiotic wastewaters.     

Deciphering the effect of sodium dodecylbenzene sulfonate on up-flow anaerobic sludge blanket treatment of synthetic sulfate-containing wastewater

• UASB reactor can work efficiently with high COD/SO₄^2- ratios when SDBS exists. • Outcome of the competition between SRB and MPA was affected by SDBS. • Presence of SDBS makes methanogens with H₂/CO₂ as a substrate dominant. • Microbial diversity decreases in the presence of SDBS. In this study, the effects of organic sulfur on anaerobic biological processes were investigated by operating two up-flow anaerobic sludge blanket (UASB) reactors with sodium dodecylbenzene sulfonate (SDBS) as a representative of organic sulfur. The results indicated that the specific methanogenic activity (SMA) and chemical oxygen demand (COD) removal efficiency of R2 (with SDBS added) were higher than those of R1 (without SDBS) when the COD/SO₄²⁻ ratio was above 5.0. However, when the COD/SO₄²⁻ ratio was lower than 5.0, the sulfate reduction efficiency of R2 was higher than that of R1. These results and the observed SDBS transformation efficiency in anaerobic reactors indicate that low concentrations of SDBS accelerate methane production and the continuous accumulation of SDBS does not weaken the reduction of sulfate. Similarly, the calculated electron flux for a COD/SO₄²⁻ ratio of 1.0 indicates that the utilization intensity of electrons by sulfate-reducing bacteria (SRB) in R2 was 36.48% higher than that of SRB in R1 and exceeded that of methane-producing archaea (MPA) under identical working conditions. Moreover, the addition of SDBS in R2 made sulfidogenesis the dominant reaction at low COD/SO₄²⁻, and Methanobacterium and Methanobrevibacter with H₂/CO₂ as the substrate and Desulfomicrobium were the dominant MPA and SRB, respectively. However, methanogenesis was still the dominant reaction in R1, and Methanosaeta with acetic acid as the substrate and Desulfovibrio were the dominant MPA and SRB, respectively.     

Enhanced carbon tetrachloride degradation by hydroxylamine in ferrous ion activated calcium peroxide in the presence of formic acid

• Complete CT degradation was achieved by employing HA to CP/Fe(II)/FA process. • Quantitative detection of Fe(II) regeneration and HO• production was investigated. • Benzoic acid outcompeted FA for the reaction with HO•. • CO₂•⁻ was the dominant reductive radical for CT removal. • Effects of solution matrix on CT removal were conducted. Hydroxyl radicals (HO•) show low reactivity with perchlorinated hydrocarbons, such as carbon tetrachloride (CT), in conventional Fenton reactions, therefore, the generation of reductive radicals has attracted increasing attention. This study investigated the enhancement of CT degradation by the synergistic effects of hydroxylamine (HA) and formic acid (FA) (initial [CT] = 0.13 mmol/L) in a Fe(II) activated calcium peroxide (CP) Fenton process. CT degradation increased from 56.6% to 99.9% with the addition of 0.78 mmol/L HA to the CP/Fe(II)/FA/CT process in a molar ratio of 12/6/12/1. The results also showed that the presence of HA enhanced the regeneration of Fe(II) from Fe(III), and the production of HO• increased one-fold when employing benzoic acid as the HO• probe. Additionally, FA slightly improves the production of HO•. A study of the mechanism confirmed that the carbon dioxide radical (CO₂•⁻), a strong reductant generated by the reaction between FA and HO•, was the dominant radical responsible for CT degradation. Almost complete CT dechlorination was achieved in the process. The presence of humic acid and chloride ion slightly decreased CT removal, while high doses of bicarbonate and high pH inhibited CT degradation. This study helps us to better understand the synergistic roles of FA and HA for HO• and CO₂•⁻ generation and the removal of perchlorinated hydrocarbons in modified Fenton systems.     

New method for efficient control of hydrogen sulfide and methane in gravity sewers: Combination of NaOH and nitrite

• The combination of NaOH and nitrite was used to control harmful gas in sewers. • Hydrogen sulfide and methane in airspace were reduced by 96.01% and 91.49%. • Changes in sewage quality and greenhouse effect by chemical dosing were negligible. • The strong destructive effects on biofilm slowed down the recovery of harmful gases. • The cost of the method was only 3.92 × 10⁻³ $/m³. An innovative treatment method by the combination of NaOH and nitrite is proposed for controlling hydrogen sulfide and methane in gravity sewers and overcome the drawbacks of the conventional single chemical treatment. Four reactors simulating gravity sewers were set up to assess the effectiveness of the proposed method. Findings demonstrated hydrogen sulfide and methane reductions of about 96.01% and 91.49%, respectively, by the combined addition of NaOH and nitrite. The consumption of NaNO₂ decreased by 42.90%, and the consumption rate of NaOH also showed a downward trend. Compared with a single application of NaNO₂, the C/N ratio of wastewater was increased to about 0.61 mg COD/mg N. The greenhouse effect of intermediate N₂O and residual methane was about 48.80 gCO₂/m³, which is far lower than that of methane without control (260 gCO₂/m³). Biofilm was destroyed to prevent it from entering the sewage by the chemical additives, which reduced the biomass and inhibited the recovery of biofilm activity to prolong the control time. The sulfide production rate and sulfate reduction rate were reduced by 92.32% and 85.28%, respectively. Compared with conventional control methods, the cost of this new method was only 3.92 × 10⁻³ $/m³, which is potentially a cost-effective strategy for sulfide and methane control in gravity sewers.     

Precise regulation of acid pretreatment for red mud SCR catalyst: Targeting on optimizing the acidity and reducibility

• The optimum SCR activity was realized by tuning the acid pretreatment. • Optimized catalysts showed NO_x conversion above 90%. • The NH₃ and NO adsorption capacity of Al-O₃-Fe is stronger than Fe-O₃-Fe. • The formation of almandine consumes Fe³⁺ and Al³⁺ and weakens their interaction. Red mud (RM), as an alkaline waste, was recently proved to be a promising substitute for the SCR catalyst. Dealkalization could improve the acidity and reducibility of red mud, which were critical for SCR reaction. However, the dealkalization effect depended on the reaction between acid solution and red mud. In this study, we realized the directional control of the chemical state of active sites through tuning the acid pretreatment (dealkalization) process. The pretreatment endpoint was controlled at pH values of 3–5 with diluted nitric acid. When the pH values of red mud were 3 and 5 (CRM-3 and CRM-5), activated catalysts showed NO_x conversion above 90% at 275°C–475°C. The high initial reaction rate, Ce³⁺/(Ce³⁺ + Ce⁴⁺) ratio, and surface acidity accounted for the excellent SCR performance of CRM-5 catalyst. Meanwhile, more Fe³⁺ on the CRM-3 surface improved the NH₃ adsorption. There was a strong interaction between Al and Fe in both CRM-5 and CRM-3 catalysts. DFT results showed that the adsorption capacity of the Al-O₃-Fe for NH₃ and NO is stronger than that of Fe-O₃-Fe, which enhanced the NO_x conversion of the catalyst. However, the almandine was formed in CRM-4, consumed part of Fe³⁺ and Al³⁺, and the interaction between Al and Fe was weakened. Also, deposited almandine on the catalyst surface covered the active sites, thus leading to lower NH₃-SCR activity.     

Preparation of nZVI embedded modified mesoporous carbon for catalytic persulfate to degradation of reactive black 5

• The MCNZVI is prepared as an interesting material for PS activation. • Graphitized carbon shells facilitate electron transfer from Fe⁰. • The MCNZVI exhibits excellent performance to degrade RB5 by ¹O₂. • The MCNZVI has high stability and reusability in the oxidation system. High-efficiency and cost-effective catalysts with available strategies for persulfate (PS) activation are critical for the complete mineralization of organic contaminants in the environmental remediation and protection fields. A nanoscale zero-valent iron-embedded modified mesoporous carbon (MCNZVI) with a core-shell structure is synthesized using the hydrothermal synthesis method and high-temperature pyrolysis. The results showed that nZVI could be impregnated within mesoporous carbon frameworks with a comparatively high graphitization degree, rich nitrogen doping content, and a large surface area and pore volume. This material was used as a persulfate activator for the oxidation removal of Reactive Black 5 (RB5). The effects of the material dosage, PS concentration, pH, and some inorganic anions (i.e., Cl⁻, SO₄²⁻) on RB5 degradation were then investigated. The highest degradation efficiency (97.3%) of RB5 was achieved via PS (20 mmol/L) activation by the MCNZVI (0.5 g/L). The pseudo-first-order kinetics (k = 2.11 × 10⁻² min⁻¹) in the MCNZVI/PS (0.5 g/L, 20 mmol/L) was greater than 100 times than that in the MCNZVI and PS. The reactive oxygen species (ROS), including ¹O₂, SO₄^·−, HO^·, and ·O₂⁻, were generated by PS activation with the MCNZVI. Singlet oxygen was demonstrated to be the primary ROS responsible for the RB5 degradation. The MCNZVI could be reused and regenerated for recycling. This work provides new insights into PS activation to remove organic contamination.     

Effect of current density on groundwater arsenite removal performance using air cathode electrocoagulation

• With the same charge, current density had little effect on As(III) removal in ACEC. • ACEC had the lowest energy consumption compared with EC/O₂ or EC/N₂. • There was a trade-off relationship between energy consumption and removal time. • The ·OH concentration in ACEC was 1.5 times of that in the EC/O₂ system. Naturally occurring arsenic enrichment in groundwater poses a huge threat to human health. Air cathode electrocoagulation (ACEC) has recently been proposed to enhance As(III) oxidation and lower energy consumption. In this study, ACEC, EC/O₂ and EC/N₂ were evaluated with different current densities from 1 to 8 mA/cm² to investigate the effect on As(III) removal in different redox environments. Current density had no appreciable effect on arsenic removal efficiency given the same charge in ACEC because the concentration ratio of Fe/H₂O₂ under different current densities remained stable. However, in EC/O₂ and EC/N₂, As(III) removal was inhibited at higher current densities (4–8 mA/cm²), likely because more Fe(II) competed with As(III) for the oxidant, leading to less effective oxidation of As(III). In all EC systems, the ·OH units generated per power consumption reached the highest value at the lowest current density. Compared with other EC systems, the ACEC system showed lower energy consumption at all current densities due to the low energy consumption of the electrode reaction and more free radical generation. A lower current density saved more energy at the expense of time, showing the trade-off relationship between energy consumption and removal time. The operation costs for As(III) removal under optimal conditions were calculated as 0.028 $/m³ for ACEC, 0.030 $/m³ for EC/O₂, and 0.085 $/m³ for EC/N₂     

Mercury removal from aqueous solution using petal-like MoS2 nanosheets

• Synthesized few-layered MoS₂ nanosheets via surfactant-assisted hydrothermal method. • Synthesized MoS₂ nanosheets show petal-like morphology. • Adsorbent showed 93% of mercury removal efficiency. • The adsorption of mercury is attributed to negative zeta potential (-21.8 mV). Recently, different nanomaterial-based adsorbents have received greater attention for the removal of environmental pollutants, specifically heavy metals from aqueous media. In this work, we synthesized few-layered MoS₂ nanosheets via a surfactant-assisted hydrothermal method and utilized them as an efficient adsorbent for the removal of mercury from aqueous media. The synthesized MoS₂ nanosheets showed petal-like morphology as confirmed by scanning electron microscope and high-resolution transmission electron microscopic analysis. The average thickness of the nanosheets is found to be about 57 nm. Possessing high stability and negative zeta potential makes this material suitable for efficient adsorption of mercury from aqueous media. The adsorption efficiency of the adsorbent was investigated as a function of pH, contact time and adsorbent dose. The kinetics of adsorption and reusability potential of the adsorbent were also performed. A pseudo-second-order kinetics for mercury adsorption was observed. As prepared MoS₂ nanosheets showed 93% mercury removal efficiency, whereas regenerated adsorbent showed 91% and 79% removal efficiency in the respective 2^nd and 3^rd cycles. The adsorption capacity of the adsorbent was found to be 289 mg/g at room temperature.     

Reutilize tire in microbial fuel cell for enhancing the nitrogen removal of the anammox process coupled with iron-carbon micro-electrolysis

• MFC promoted the nitrogen removal of anammox with Fe-C micro-electrolysis. • Reutilize pyrolysis waste tire as micro-electrolysis and electrode materials. • Total nitrogen removal efficiency of modified MFC increased to 85.00%. • Candidatus kuenenia and SM1A02 were major genera responsible for nitrogen removal. In this study, microbial fuel cells (MFCs) were explored to promote the nitrogen removal performance of combined anaerobic ammonium oxidation (anammox) and Fe-C micro-electrolysis (CAE) systems. The average total nitrogen (TN) removal efficiency of the modified MFC system was 85.00%, while that of the anammox system was 62.16%. Additionally, the effective operation time of this system increased from six (CAE system alone) to over 50 days, significantly promoting TN removal. The enhanced performance could be attributed to the electron transferred from the anode to the cathode, which aided in reducing nitrate/nitrite in denitrification. The H⁺ released through the proton exchange membrane caused a decrease in the pH, facilitating Fe corrosion. The pyrolyzed waste tire used as the cathode could immobilize microorganisms, enhance electron transport, and produce a natural Fe-C micro-electrolysis system. According to the microbial community analysis, Candidatus kuenenia was the major genus involved in the anammox process. Furthermore, the SM1A02 genus exhibited the highest abundance and was enriched the fastest, and could be a novel potential strain that aids the anammox process.     

Zero-valent manganese nanoparticles coupled with different strong oxidants for thallium removal from wastewater

• Nano zero-valent manganese (nZVMn, Mn⁰) is synthesized via borohydrides reduction. • Mn⁰ combined with persulfate/hypochlorite is effective for Tl removal at pH 6-12. • Mn⁰ can activate persulfate to form hydroxyl and sulfate radicals. • Oxidation-induced precipitation and surface complexation contribute to Tl removal. • Combined Mn⁰-oxidants process is promising in the environmental field. Nano zero-valent manganese (nZVMn, Mn⁰) was prepared through a borohydride reduction method and coupled with different oxidants (persulfate (S₂O₈²⁻), hypochlorite (ClO⁻), or hydrogen peroxide (H₂O₂)) to remove thallium (Tl) from wastewater. The surface of Mn⁰ was readily oxidized to form a core-shell composite (MnO_x@Mn⁰), which consists of Mn⁰ as the inner core and MnO_x (MnO, Mn₂O₃, and Mn₃O₄) as the outer layer. When Mn⁰ was added alone, effective Tl(I) removal was achieved at high pH levels (>12). The Mn⁰-H₂O₂ system was only effective in Tl(I) removal at high pH (>12), while the Mn⁰-S₂O₈²⁻ or Mn⁰-ClO⁻ system had excellent Tl(I) removal (>96%) over a broad pH range (4–12). The Mn⁰-S₂O₈²⁻ oxidation system provided the best resistance to interference from an external organic matrix. The isotherm of Tl(I) removal through the Mn⁰-S₂O₈²⁻ system followed the Freundlich model. The Mn⁰ nanomaterials can activate persulfate to produce sulfate radicals and hydroxyl radicals. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy suggested that oxidation-induced precipitation, surface adsorption, and electrostatic attraction are the main mechanisms for Tl(I) removal resulting from the combination of Mn⁰ and oxidants. Mn⁰ coupled with S₂O₈²⁻/ClO⁻ is a novel and effective technique for Tl(I) removal, and its application in other fields is worthy of further investigation.     

Identification of sources,characteristics and photochemical transformations of dissolved organic matter with EEM-PARAFAC in the Wei River of China

• The source of DOM in surface water and sediment is inconsistent. • The DOC content changes differently in surface water and sediment. • The content of DOC in the surface water is lower than that in the sediment. • The DOM in the surface water had higher photodegradation potentials than sediment. Dissolved organic matter (DOM) in rivers is a critical regulator of the cycling and toxicity of pollutants and the behavior of DOM is a key indicator for the health of the environment. We investigated the sources and characteristics of DOM in surface water and sediment samples of the Wei River, China. Dissolved organic carbon (DOC) concentration and ultraviolet absorbance at 254 nm (UV₂₅₄) increased in the surface water and were decreased in the sediment downstream, indicating that the source of DOM in the water differed from the sediment. Parallel factor (PARAFAC) analysis of the excitation-emission matrices (EEM) revealed the presence of terrestrial humus-like, microbial humus-like and tryptophan-like proteins in the surface water, whereas the sediment contained UVA humic-like, UVC humic-like and fulvic-like in the sediment. The DOM in the surface water and sediment were mainly derived from microbial metabolic activity and the surrounding soil. Surface water DOM displayed greater photodegradation potential than sediment DOM. PARAFAC analysis indicated that the terrestrial humic-like substance in the water and the fulvic-like component in the sediment decomposed more rapidly. These data describe the characteristics of DOM in the Wei River and are crucial to understanding the fluctuations in environmental patterns.