无线数据通信网中的信道接入协议研究

信道接入协议（MAC）是无线数据通信协议的重要组成部分。由于无线信道是一个开放、共享的信道，网络节点在通信过程中存在隐终端和暴露终端问题。基于目前无线通信常用的MAC协议存在的问题，着重分析了基于扩频码的信道接入协议，该协议利用扩频码的正变特性，使得网络中各节点可以同时占用信道而互不干扰，较好地解决了信道争用问题，提高了系统效率。同时指出，在选择MAC协议时，应根据无线网络的拓扑结构及特点灵活选择，以提高网络性能。     

基于节点接入能力的ad hoc网络按需路由协议

基于802.11协议MAC层重传策略,提出一个衡量节点接入能力的参数CAM(capacity of access to medium),以体现节点周围信道的繁忙程度及其抢占信道能力。在此基础上,联合MAC层和网络层进行跨层设计,提出了一个拥塞感知路由CAOR(congestion aware on-demand routing)协议。仿真表明:该协议能够在降低开销的前提下,显著增加网络吞吐量,并降低平均端到端的时延。     

太赫兹无线个域网公平高效的MAC层优化机制

针对太赫兹无线个域网双信道媒体访问控制(Medium Access Control, MAC)协议中存在的信道资源分配公平性差、数据帧重传效率低和控制开销较高的问题,提出了一种公平高效的MAC层优化机制。新机制采用基于历史时隙申请信息的信道资源分配策略优化时隙分配公平性,根据信道质量自适应选择数据帧重传机制,控制节点从申请时隙的节点发送的控制帧中的“duration”字段提取时隙申请信息,省略时隙申请帧的发送,从而降低数据帧排队时延和控制开销,提高吞吐量。仿真结果表明,与TAB-MAC和MDP-MAC协议的机制相比,所提机制的数据帧平均排队时延降低了15%,吞吐量提高了5%。     

面向实时业务的认知无线网络 MAC 层频谱接入方案

摘 要：为满足认知无线网络中宽带业务实时传输的需求,提出低延迟的MAC层频谱接入方案,包括频谱感知调度与信道接入竞争两部分。在频谱感知阶段,认知用户选取最佳可用信道数实现感知与传输的延迟最小化;在信道接入竞争阶段,协议考虑频谱资源动态变化的特点,通过设计数据帧格式以及邻居节点协同侦听机制,减小信道冲突与“聋终端”的影响。理论与实验结果表明,与传统的认知无线网络MAC层协议相比,提出的接入方案数据传输延迟更短,同时在授权信道空闲率较大时吞吐量性能略优。     

一种基于Ad Hoc网络的协作MAC方案

在 IEEE 802.11b MAC层协议的研究基础上,提出了一种基于无线Ad Hoc网络的最佳中继选择策略,该策略综合考虑瞬时信道信息和节点剩余能量,能够有效防止信道条件好的节点的过度使用,并能保证系统高吞吐量。文中以饱和吞吐量和网络生存时间为性能指标,对新算法和以往协作MAC算法进行仿真和比较,结果表明新算法在网络吞吐量下降不明显的情况下,能大大增加网络生存时间。     

基于Ad hoc网络的退避算法研究

在移动Ad hoc网络中,无线信道由多个节点共享,合理协调多个节点访问共享信道的媒体接入控制(MAC,Medium Access Control)协议是移动Ad hoc网络的关键技术之一。退避算法在MAC协议中起着至关重要的作用。针对目前退避算法存在的问题,本文提出了一种改进算法,根据网络节点发送数据包成功与否,预测网络信道空闲或繁忙的趋势,应用趋势合理地调节退避算法中节点发送数据时退避值的大小,并通过Omnet++软件对算法进行了仿真分析对比。     

基于多信道预约的传感器网络MAC协议研究

针对传感器网络中三重隐终端问题,提出了一种基于自适应占空比的多信道MAC协议—MCR,MCR通过多信道预约机制高效地解决了该问题。在理论分析中,通过最小化节点平均信道切换次数的下界得出了节点的最优占空比。为验证MCR中多信道预约和自适应占空比机制的性能,进行了模拟和真实实验,实验结果表明,与其他MAC协议相比,随着信道数及网络负载的增加,MCR提高了网络吞吐量,降低了传输所消耗的能量。     

移动自组网中联合优化设计的MAC/路由协议

文章针对节点数量多、密度大的一类移动自组网提出了一种跨层联合设计的MAC/路由协议.在MAC层上采用基于调度的信道分配算法以减少通信冲突,在网络层上结合使用表驱动路由和基于地理位置的路由来提高协议适应动态拓扑的能力,并设计了适合TDMA MAC协议的高效的消息交互机制.在OPNET仿真平台上与AODV/802.11和G...     

太赫兹网络中基于中继的高效双信道MAC协议

现有的太赫兹无线个域网双信道介质访问控制(MAC)协议工作在WiFi和太赫兹信道。由于这两种信道的频率相差极大,导致使用全向天线和定向天线的覆盖范围各不相同,这样便会使节点之间的消息传输成功率大大降低,同时也降低了网络整体的吞吐量。另外,在现有的太赫兹无线网络双信道MAC协议中还存在一定的冗余控制开销,这导致了信道利用率低。基于此,文章提出一种太赫兹无线网络中基于中继的高效双信道MAC协议(HE-BRMAC),HE-BRMAC分为中继辅助和自适应减少控制开销机制。通过这两种机制可达到提高消息传输成功率、提升网络整体吞吐量、减少控制开销和提高信道利用率的效果,尤其当节点数较多时,HE-BRMAC的效果更为显著。     

选用最优数据信道的认知无线电MAC协议

如何选择数据信道进行数据的传输是认知无线电网络MAC协议的重要环节,许多现有的MAC机制在选用数据信道没有考虑信道的可用概率,而可用概率对网络性能有着重要的影响。提出了一种最优信道传输的认知无线电MAC协议。次用户在频谱感知后,选用质量最优数据信道对数据进行传输,评价信道质量的标准中考虑了信道的可用概率。最后,使用ns...     

Development of the readout system for waveguide multilayer optical card

Waveguide multilayer optical card （WMOC） is a novel storage device of three-dimensional optical information. An advanced readout system fitting for the WMOC is introduced in this paper. The hardware mainly consists of the light source for reading, WMOC, motorized stages addressing unit, microscope imaging unit, CCD detecting unit and PC controlling ＆ processing unit. The movement of the precision motorized stage is controlled by the computer through Visual Basic （VB） language in software. A control panel is also designed to get the layer address and the page address through which the position of the motorized stages can be changed. The WMOC readout system is easy to manage and the readout result is directly displayed on computer monitor.     

Nanoimprint Lithography -A Next Generation High Volume Lithography Technique

IntroductionNanoimprint Lithography is a well-acknowl-edged low cost, high resolution, large area pattern-ing process. It includes the most promising methods,high-pressure hot embossing lithography (HEL) [2],UV-cured imprinting (UV-NIL) [3] and micro contactprinting (m-CP, MCP) [4]. Curing of the imprintedstructures is either done by subsequent UV-lightexposure in the case of UV-NIL or by cooling downbelow the glass transition temperature of the ther-moplastic material in case of HEL…     

Collinear phase-matching study of terahertz-wave generation via difference frequency mixed in GaAs and Inp

The collinearly phase-matching condition of terahertz-wave generation via difference frequency mixed in GaAs and InP is theoretically studied. In collinear phase-matching, the optimum phase-matching wave hands of these two crystals are calculated. The optimum phase-matching wave bands in GaAs and lnP are 0.95-1.38μm and 0.7-0.96μm respectively. The influence of the wavelength choice of the pump wave on the coherent length in THz-wave tuning is also discussed. The influence of the temperature alteration on the phase-matching and the temperature tuning properties in GaAs crystal are calculated and analyzed. It can serve for the following experiments as a theoretical evidence and a reference as well.     

Effects of the alloy compositions on the phonon-polaritons in ternary mixed crystals

Composition dependence of bulk and surface phonon-polaritons in ternary mixed crystals are studied in the framework of the modified random-element-isodisplacement model and the Bom-Huang approximation. The numerical results for Several Ⅱ - Ⅵ and Ⅲ- Ⅴ compound systems are performed, and the polariton frequencies as functions of the compositions for ternary mixed crystals AlxGa1-xAs, GaPxAS1-x, ZnSxSe1-x, GaAsxSb1-x, GaxIn1-xP, and ZnxCd1-xS as examples are given and discussed. The results show that the dependence of the energies of two branches of bulk phonon-polaritons which have phonon-like characteristics, and surface phonon-polaritons on the compositions of ternary mixed crystals are nonlinear and different from those of the corresponding binary systems.     

Influence of PVK ： NPB hole transporting layer on the characteristics of organic light-emitting devices

A doping system consisting of NPB and PVK is employed as a composite hole transporting layer （CHTL）. By adjusting the component ratio of the doping system, a series of devices with different concentration proportion of PVK ： NPB are constracted. The result shows that doping concentration of NPB enhances the competence of hole transporting ability, and modifies the recombination region of charge as well as affects the surface morphology of doped film. Optimum device with a maximum brightness of 7852 cd/m^2 and a power efficiency of 1.75 lm/W has been obtained by choosing a concentration proportion of PVK ： NPB at 1：3.     

New insert layer structure OLEDs

An insert layer structure organic electroluminescent device（OLED） based on a new luminescent material （Zn（salen）） is fabricated. The configuration of the device is ITO/CuPc/NPD/Zn（salen）/Liq/LiF/A1/CuPc/NPD/Zn（salen）/Liq/LiF/A1. Effective insert electrode layers comprising LiF（1nm）/Al（5 nm） are used as a single semitransparent mirror, and bilayer cathode LiF（1 nm）/A1（100 nm） is used as a reflecting mirror. The two mirrors form a Fabry-Perot microcavity and two emissive units. The maximum brightness and luminous efficiency reach 674 cd/m^2 and 2.652 cd/A, respectively, which are 2.1 and 3.7 times higher than the conventional device, respectively. The superior brightness and luminous efficiency over conventional single-unit devices are attributed to microcavity effect.     

Analysis of error performance on Turbo coded FDPIM

Due to variable symbol length of digital pulse interval modulation（DPIM）, it is difficult to analyze the error performances of Turbo coded DPIM. To solve this problem, a fixed-length digital pulse interval modulation（FDPIM） method is provided. The FDPIM modulation structure is introduced. The packet error rates of uncoded FDPIM are analyzed and compared with that of DPIM. Bit error rates of Turbo coded FDPIM are simulated based on three kinds of analytical models under weak turbulence channel. The results show that packet error rate of uncoded FDPIM is inferior to that of uncoded DPIM. However, FDPIM is easy to be implemented and easy to be combined, with Turbo code for soft-decision because of its fixed length. Besides, the introduction of Turbo code in this modulation can decrease the average power about 10 dBm, which means that it can improve the error performance of the system effectively.     

A method for calculating the center position of collimated light

It is a key problem to accurately calculate beam spots＇ center of measuring the warp by using a collimated laser. A new method, named double geometrical center method （DGCM）, is put forward for the first time. In this method, a plane wave perpendicularly irradiates an aperture stop, and a charge couple device （CCD） is employed to receive the diffraction-beam spots, then the geometrical centers of the fast and the second diffraction-beam spots are calculated respectively, and their mean value is regarded as the center of datum beam. In face of such adverse instances as laser intension distributing defectively, part of the image being saturated, this method can still work well. What＇s more, this method can detect whether an unacceptable error exits in the courses of image receiving, processing and calculating. The experimental results indicate the precision of this method is high.     

Resolution Enhancement Technology:Integrated Process Solutions using OPC

DUV lithography, using the 248 nm wavelength, is a viable manufacturing option for devices with features at 130 nm and less. Given the low kl value of the lithography, integrated process development is a necessary method for achieving acceptable process latitude. The application of assist features for rule based OPC requires the simultaneous optimization of the mask, illumination optics and the resist.Described in this paper are the details involved in optimizing each of these aspects for line and space imaging.A reference pitch is first chosen to determine how the optics will be set. The ideal sigma setting is determined by a simple geometrically derived expression. The inner and outer machine settings are determined, in turn,with the simulation of a figure of merit. The maximum value of the response surface of this FOM occurs at the optimal sigma settings. Experimental confirmation of this is shown in the paper.Assist features are used to modify the aerial image of the more isolated images on the mask. The effect that the diffraction of the scattering bars (SBs) has on the image intensity distribution is explained. Rules for determining the size and placement of SBs are also given.Resist is optimized for use with off-axis illumination and assist features. A general explanation of the material' s effect is discussed along with the affect on the through-pitch bias. The paper culminates with the showing of the lithographic results from the fully optimized system.     

Preparation and Characterization of TaN ALD Precursors

High purity organic-tantalum precursors for thin film ALD TaN were synthesized and characterized.Vapor pressure and thermal stability of these precursors were studied.From the vapor pressure analysis,it was found that TBTEMT has a higher vapor pressure than any other published liquid TaN precursor,including TBTDET,TAITMATA,and IPTDET.Thermal stability of the alkyl groups on the precursors was investigated using a 1H NMR technique.The results indicated that the tertbutylimino group is the most stable group on TBTDET and TBTEMT as compared to the dialkylamido groups.Thermal stability of TaN precursors decreased in the following order:TBTDET ＞ PDMAT ＞ TBTEMT.In conclusion,precursor vapor pressure and thermal stability were tuned by making slight variations in the ligand sphere around the metal center.