FePO4的制备及其在锂电池中的应用

采用不同的方法制备磷酸高铁 ,对其在锂金属二次电池中的充放电比容量进行测定 ,研究不同煅烧温度对其性能的影响 .通过机械研磨的方法 ,获得高比容量的 Fe PO4样品 .在电流密度为 0 .13m A· cm-2 时 ,首次放电比容量达 132 .0 m A· h· g-1.通过实验证明 ,结晶状磷酸高铁也可以获得具有与无定形磷酸高铁相近的充放电容量 .该方法提供一种原料价格低廉、制造简单和充放电容量高的正极活性材料 ,可应用于金属锂电池     

中间相炭微球的结构对其电化学性能的影响

为了研究不同结构的炭微球对其电化学性能的影响,用聚合法以煤焦油为原料在添加和不添加炭黑的条件下制备中间相炭微球,用高倍扫描电镜观察了它们的形貌和结构,并且研究了它们作为锂离子电池炭负极材料的电化学性能.研究结果表明,在不添加炭黑的条件下得到"地球仪"型结构;对于这种结构的中间相炭微球,锂离子容易脱嵌,首次放电容量可达298.0mA·h·g-1,不可逆容量达48.5mA·h·g-1,但循环寿命短;而添加炭黑时得到层状混合结构,这种结构的中间相炭微球首次放电容量较小,为288mA·h·g-1,不可逆容量相对较大,为81.3mA·h·g-1,但衰减慢,循环寿命长.     

CuO微米梭的制备及其电化学性能研究

尽管各种各样的CuO纳米结构已被广泛应用于锂离子电池负极材料的研究,但将CuO微米梭作为锂离子电池负极材料却鲜有报道. 运用简单的溶剂热法制备大量的CuO微米梭,并用作锂离子电池负极材料. 实验表明,CuO微米梭在电流密度为100 mA g-1下充放电循环100次后,放电容量依然保持在484 mAh g-1. CuO微米梭优异的电化学性能归功于其独特的梭形结构. 这种结构在锂离子电池充放电过程中可以缩短锂离子和电子的传输距离,缓解体积膨胀效应.     

锂离子电池正极材料尖晶石型LiMn2O4的制备及其掺杂改性

采用固相合成法制备了锂离子电池用尖晶石型LiMn2O4正极材料,并通过同时加入Cr3 和F对材料进行了体相掺杂改性.用扫描电子显微镜和X射线衍射研究了材料的表面形貌和晶体结构,用充放电循环实验对制备的锂离子电池性能进行了测试.结果表明:未掺杂的LiMn2O4正极材料首次放电容量为115.3mAh·g-1,循环25次后容量降为96mAh·g-1;掺杂Cr3 和F的材料同样具有尖晶石型结构,随掺杂量增加,首次放电容量略有降低,但循环性能有较明显改善,充放电效率提高,其中掺杂量为0.10的样品首次放电容量为111.5 mAh·g-1,循环25次后容量保持率达91.8%.     

中间相炭微球的粒径对其结构和性能的影响

采用X射线衍射、粒径分析、扫描电子显微镜、BET比表面积分析及电化学方法研究了粒径对中间相炭微球结构和性能的影响.研究结果表明:随着粒径的增加,中间相炭微球的堆积密度增大,比表面积减小;中间相炭微球电极的充电容量和不可逆容量减小,可逆容量与首次充放电效率增加;以中间相炭微球为负极制成063448型锂离子电池的放电容量随着中间相炭微球平均粒径的增大而增加,不可逆容量减少;以平均粒径为19.09μm的中间相炭微球为负极制成的电池放电容量为838 mA·h,首次充放电效率为87.29%,循环100次后的容量保持率为92.4%.     

兰炭基活性炭材料的制备及其电化学性能

以兰炭为原料,KOH为活化剂,利用微波辐射对兰炭进行脱氢、炭化、活化制备活性炭材料.采用X射线衍射(XRD)、傅里叶红外光谱(FTIR),透射电子显微镜(TEM)等手段对材料的结构和形貌进行表征.通过恒流充放电、循环伏安(CV)对材料的电化学性能进行测试.结果表明:兰炭基活性炭用于锂离子电池负极材料具有优异的循环稳定性和良好的库伦效率.材料在充放电电流密度为200mA·g-1时,首次放电比容量达1 850mAh·g-1,循环60周后容量仍然保持在713.8mAh·g-1.     

锂离子动力蓄电池充放电基本性能的研究

为了考察锂离子动力蓄电池应用于电动汽车的可行性 ,本文以MCMB和LiCoO2 为正负极材料 ,自行设计组装了 5A·h、2 5A·h和 50A·h的方形层叠式锂离子动力蓄电池 ,用恒电流限电压充放电方法研究了其在不同电流下的放电行为和荷电保持能力 .研究结果表明 :以0 .2C倍率、10 0 %DOD放电时 50A·h电池的质量比能量和能量密度可分别达到 10 7.4W·h/kg和 185.1W·h/L ,已经超过了美国电池先进联合体 (USABC)规定的动力蓄电池的中期开发目标。 5Ah电池的 1C倍率放电容量可保持 0 .1C倍率放电容量的 79.35% .电池的荷电保持性能良好 ,日平均自放电率小于 0 .32 4 % /d ,开路电压月下降只有 0 .1V左右     

Cu-MOF/rGO锂离子电池负极材料的制备及电化学性能

采用石墨烯掺杂的Cu-有机骨架化合物(Cu-MOF)复合材料(Cu-MOF/r GO)作为锂离子电池负极材料,研究其电化学性能.结果表明:在充放电电流密度为50 m A/g时,充放电循环50次后,材料的放电比容量可达到520m Ah/g.同时该材料也显示出较好的倍率性能和较高的库仑效率.Cu-MOF/r GO是一种具有前景的锂离子电池负极材料.     

金属有机骨架材料ZnCo_2O_4/ZnO中空纳米盒的制备及其电化学性能

石墨是锂离子电池商用的负极材料,但其较低的比容量(372.0 m A·h/g)难以满足不断增长的高容量需求.因此,设计和制备高性能负极材料是提升锂离子电池能量密度及性能的关键因素之一.首先以金属有机框架ZIF-8为模板构建出ZIF-8@ZIF-67核壳复合结构,后经简单煅烧处理制备中空ZnCo_2O_4/ZnO复合纳米材料,并通过XRD, SEM, TEM以及恒流充放电等对其结构、形貌及电化学性能进行研究.结果表明:中空ZnCo_2O_4/ZnO复合纳米材料作为锂离子电池负极材料时表现出良好的电化学性能,初次放电容量达到1 536.8 m A·h/g;以100 m A/g电流密度充放电100次后,比容量稳定在780 m Ah/g,显示出优良的电化学储能特性.     

高性能锂离子电池负极材料一氧化锰/石墨烯复合材料的合成

通过冻干-煅烧合成了一氧化锰/石墨烯(MnO/rGO)复合材料,并将其用作锂离子电池负极材料.在500 mA·g-1的电流密度下,MnO/rGO复合材料表现出高达830 mAh·g-1的可逆容量,且在充放电循环160圈后,其可逆容量依然高达805 mAh·g-1.倍率测试结果显示,循环225圈后,在2.0 A·g-1的电流密度下,其可逆容量高达412 mAh·g-1.复合材料中的石墨烯在提高材料导电性的同时有效地缓解了一氧化锰充放电过程中的体积膨胀.通过对比容量-电压的微分分析,发现复合材料超出一氧化锰理论容量的部分是由形成了更高价态的锰引起的.MnO/rGO复合材料比纯一氧化锰(p-MnO)更容易出现高价态的锰,可能是因为rGO上残留的氧为电极反应提供了额外所需的氧源.该一氧化锰/石墨烯复合材料因其简单绿色的合成过程及优异的电化学性质,有望在未来的锂电负极中得到广泛的实际应用.     

Markedness and its Interpretation in Language Use

Language markedness is a common phenomenon in languages, and is reflected from hearing, vision and sense, i.e. the variation in the three aspects such as phonology, morphology and semantics. This paper focuses on the interpretation of markedness in language use following the three perspectives, i.e. pragmatic interpretation, psychological interpretation and cognitive interpretation, with an aim to define the function of markedness.     

Lower Paleozoic oil relationships within Williston Basin, Canada

The Williston Basin is a significant petroleum province, containing oil production zones that include the Middle Cambrian to Lower Ordovician, Upper Ordovician, Middle Devonian, Upper Devonian and Mississippian and within the Jurassic and Cretaceous. The oils of the Williston Basin exhibit a wide range of geochemical characteristics defined as "oil families", although the geochemical signature of the Cambrian Deadwood Formation and Lower Ordovician Winnipeg reservoired oils does not match any "oil family". Despite their close stratigraphic proximity, it is evident that the oils of the Lower Palaeozoic within the Williston Basin are distinct. This suggests the presence of a new "oil family" within the Williston Basin. Diagnostic geochemical signatures occur in the gasoline range chromatograms, within saturate fraction gas chromatograms and biomarker fingerprints. However, some of the established criteria and cross-plots that are currently used to segregate oils into distinct genetic families within the basin do not always meet with success, particularly when applied to the Lower Palaeozoic oils of the Deadwood and Winnipeg Formation.     

An Analysis of Catherine＇s Character——Wuthering Heights

Wuthering Heights, Emily Bronte＇s only novel, was published in December of 1847 under the pseudonym Ellis Bell. The book did not gain immediate success, but it is now thought one of the finest novels in the English language. Catherine is the key character of this masterpiece, because everybody and everything center on her though she had a short life. We can understand this masterpiece better if we know Catherine well.     

Characterization of Ordovician carbonate reservoirs, southeastern Saskatchewan, Canada

The discovery of the prolific Ordovician Red River reservoirs in 1995 in southeastern Saskatchewan was the catalyst for extensive exploration activity which resulted in the discovery of more than 15 new Red River pools. The best yields of Red River production to date have been from dolomite reservoirs. Understanding the processes of dolomitization is, therefore, crucial for the prediction of the connectivity, spatial distribution and heterogeneity of dolomite reservoirs.The Red River reservoirs in the Midale area consist of 3～4 thin dolomitized zones, with a total thickness of about 20 m, which occur at the top of the Yeoman Formation. Two types of replacement dolomite were recognized in the Red River reservoir: dolomitized burrow infills and dolomitized host matrix. The spatial distribution of dolomite suggests that burrowing organisms played an important role in facilitating the fluid flow in the backfilled sediments. This resulted in penecontemporaneous dolomitization of burrow infills by normal seawater. The dolomite in the host matrix is interpreted as having occurred at shallow burial by evaporitic seawater during precipitation of Lake Almar anhydrite that immediately overlies the Yeoman Formation. However, the low δ18O values of dolomited burrow infills (-5.9‰～ -7.8‰, PDB) and matrix dolomites (-6.6‰～ -8.1‰, avg. -7.4‰ PDB) compared to the estimated values for the late Ordovician marine dolomite could be attributed to modification and alteration of dolomite at higher temperatures during deeper burial, which could also be responsible for its 87Sr/86Sr ratios (0.7084～0.7088) that are higher than suggested for the late Ordovician seawaters (0.7078～0.7080). The trace amounts of saddle dolomite cement in the Red River carbonates are probably related to "cannibalization" of earlier replacement dolomite during the chemical compaction.     

Features of Women's language

Language is a means of verbal communication. People use language to communicate with each other. In the society, no two speakers are exactly alike in the way of speaking. Some differences are due to age, gender, statue and personality. Above all, gender is one of the obvious reasons. The writer of this paper tries to describe the features of women＇s language from these perspectives： pronunciation, intonation, diction, subjects, grammar and discourse. From the discussion of the features of women＇s language, more attention should be paid to language use in social context. What＇s more, the linguistic phenomena in a speaking community can be understood more thoroughly.     

Design and analysis of generic LBS application developing platform

Location based services is promising due to its novel working style and contents.A software platform is proposed to provide application programs of typical location based services and support new applications developing efficiently. The analysis shows that this scheme is easy implemented, low cost and adapt to all kinds of mobile nework system.     

橡胶颗粒沥青混合料低温抗裂性试验研究

以AC-13级配为基础,将橡胶颗粒代替部分集料掺入混合料中,以低温弯曲试验为评价方法对不同橡胶颗粒掺量下沥青混合料的低温抗裂性进行研究,并引入应变能密度值对混合料的低温抗裂性进行综合评价.试验结果表明:橡胶颗粒沥青混合料试件的破坏微应变均超过2 300,满足冬寒区的技术指标;无论是否掺加橡胶颗粒,随着温度的下降,沥青混合料破坏时的最大弯拉强度增大,弯拉应变降低,劲度模量增大;弯曲应变能密度在胶粒掺量为1%左右时具有较大的弯曲应变能密度值,此时橡胶颗粒沥青混合料具有较好的低温抗裂性.     

A computer generator for randomly layered structures

AcomputergeneratorforrandomlylayeredstructuresYUJia shun1,2,HEZhen hua2(1.TheInstituteofGeologicalandNuclearSciences,NewZealand;2.StateKeyLaboratoryofOilandGasReservoirGeologyandExploitation,ChengduUniversityofTechnology,China)Abstract:Analgorithmisintrod…     

低渗透非均质砂岩油藏启动压力梯度研究

理论推导与室内实验相结合,建立了低渗透非均质砂岩油藏启动压力梯度确定方法。首先借助油藏流场与电场相似的原理,推导了非均质砂岩油藏启动压力梯度计算公式。其次基于稳定流实验方法,建立了非均质砂岩油藏启动压力梯度测试方法。结果表明:低渗透非均质砂岩油藏的启动压力梯度确定遵循两个等效原则。平面非均质油藏的启动压力梯度等于各级渗透率段的启动压力梯度关于长度的加权平均;纵向非均质油藏的启动压力梯度等于各渗透率层的启动压力梯度关于渗透率与渗流面积乘积的加权平均。研究成果可用于有效指导低渗透非均质砂岩油藏的合理井距确定,促进该类油藏的高效开发。     

Quantitative trait loci （QTLs） for quality traits related to protein and starch in wheat

Quality traits in wheat （Triticum aestirum L.） were studied by quantitative trait locus （QTL） analysis in a recombinant inbred line （RIL） population, a set of 131 lines derived from Chuan 35050 × Shannong 483 cross （ChSh）. Grains from RILs were assayed for 21 quality traits related to protein and starch. A total of 35 putative QTLs for 19 traits with a single QTL explaining 7.99-40.52% of phenotypic variations were detected on 10 chromosomes, 1D, 2A, 2D, 3B, 3D, 5A, 6A, 6B, 6D, and 7B. The additive effects of 30 QTLs were positive, contributed by Chuan 35050, the remaining 5 QTLs were negative with the additive effect contributed by Shannong 483. For protein traits, 15 QTLs were obtained and most of them were located on chromosomes 1 D, 3B and 6D, while 20 QTLs for starch traits were detected and most of them were located on chromosomes 3D, 6B and 7B. Only 7 QTLs for protein and starch traits were co-located in three regions on chromosomes 1D, 2A and 2D. These protein and starch trait QTLs showed a distinct distribution pattern in certain regions and chromosomes. Twenty-two QTLs were clustered in 6 regions of 5 chromosomes. Two QTL clusters for protein traits were located on chromosomes 1D and 3B, respectively, three clusters for starch traits on chromosomes 3D, 6B and 7B, and one cluster including protein and starch traits on chromosome 1D.