芳纶纤维等离子体接枝改性处理研究

采用等离子体接枝对芳纶纤维表面进行改性处理,采用XPS、浸润性、界面剪切强度对等离子体接枝处理前后的表面组成、复合材料界面粘接性能等进行了研究,结果表明:等离子体接枝处理可以有效地提高芳纶纤维表面的极性官能团,增加与基体树脂-环氧树脂的浸润性,进而提高芳纶/环氧复合材料的界面粘接强度.     

空气介质阻挡放电等离子体对国产芳纶ⅢA表面改性的研究

采用空气介质阻挡放电等离子体对国产芳纶ⅢA进行表面处理,优化了其处理工艺。用SEM、XPS等方法研究了处理前后纤维表面形态和化学状态的变化,通过短梁剪切试验评价了芳纶ⅢA/环氧复合材料的抗层间剪切强度。结果表明:经空气等离子体处理后芳纶ⅢA表面粗糙度增加,极性增强,纤维力学性能无明显变化,芳纶ⅢA/环氧复合材料的抗层间剪切强度提高了18%。     

洋麻/芳纶混纺织物增强复合材料的力学性能研究

为了探究四种洋麻/芳纶不同混纺比对其混纺织物增强复合材料力学性能的影响,对以环氧树脂为基体,精细化处理的洋麻和对位芳纶不同混纺比机织物为增强体的复合材料进行力学性能测试,并对洋麻纤维扫描电子显微镜(SEM)及傅里叶红外光谱(FTIR)测试分析纤维表面粗糙度及极性变化,从而来分析力学测试结果。结果表明,洋麻/芳纶30/70混纺织物增强复合材料弯曲强度最高,为248.81MPa,弯曲模量为12.91GPa,与纯芳纶织物增强复合材料相比,分别提高4.9%和7.1%;而洋麻/芳纶20/80混纺织物增强复合材料剪切强度最高,为24.58MPa,与纯芳纶织物增强复合材料相比,提高18.6%。SEM及FTIR表明洋麻纤维精细化处理后,纤维表面粗糙度增加,极性降低,提高了增强体与树脂的界面结合力,从而改善了复合材料的弯曲、剪切性能。     

低温等离子体处理对芳纶/环氧界面性能的影响

在采用低温等离子体对芳纶纤维进行表面处理后，用扫描电镜观察处理前后的纤维表面，测试了纤维的拉伸性能，并用单纤维抽拔法对芳纶纤维／环氧树脂的界面性能做了定量的表征。实验结果表明：经低温等离子体处理后，芳纶纤维表面变得粗糙，拉伸强度随处理时间延长而下降，纤维初始模量和断裂伸长率略有下降，而芳纶／环氧界面的粘结强度有所提高。     

低温等离子体改性芳纶1414的研究

对芳纶1414进行低温等离子体表面改性以改善其构成复合材料时的界面黏结性能。设计正交试验,得到低温等离子体处理芳纶1414的最佳条件为放电功率100 W,处理时间300 s,放电压强20 Pa。采用电子单纤维强力机、纤维摩擦因数测定仪、纤维接触角测量仪、扫描电子显微镜和傅里叶变换红外光谱仪对改性前后的芳纶1414进行性能表征。结果表明:经过低温等离子体改性的芳纶1414的断裂强力较原样下降了6.3%,静摩擦因数上升了15.7%,表面接触角减小了36.8%,纤维表面出现微小均匀的凹槽,增大了比表面积,引入了自由基团,增大了表面反应活性,从而改善了与树脂基体复合时的黏结强度。     

常压等离子体改善高性能纤维粘结性的研究

以氦气为载气,氧气为反应气体,对高强度聚乙烯和Twaron 1000芳纶两种高性能纤维进行常压等离子体处理,来改善纤维的粘结性能;采用单纤维抽拔实验测定等离子体处理前后纤维与环氧树脂之间的界面剪切力;利用原子力显微镜和X射线光电子能谱仪分析等离子体处理前后纤维表面形态和化学成分的变化。结果表明:高强度聚乙烯纤维和芳纶经常压等离子体处理后,纤维表面粗糙度增加,纤维表面碳元素含量下降,羟基、羧基等含氧或氮的极性基团增加,纤维粘结性能得到提高,但其强度无明显变化。     

介质阻挡放电等离子体处理芳纶的表面性能研究

采用介质阻挡放电(DBD)装置对芳纶1414表面进行改性处理,探讨低温等离子体处理对纤维表面性能的影响。结果表明:经过DBD等离子体处理后,芳纶1414纤维表面粗糙程度加剧,粘结性能和浸润性能有了明显的改善;当DBD等离子体处理功率为200～300 W,时间为60 s,氩气流量为2～3 L/min时,芳纶1414的界面剪切强度从处理前的11.9 MPa上升到14.2 MPa,接触角由处理前的85.0°下降到了60.6°。     

氨气等离子体改性处理芳纶Ⅲ表面的研究

以氨气为反应气体,对芳纶Ⅲ进行等离子体表面改性处理,研究了等离子体处理时间和处理功率对纤维表面性能的影响;采用X射线光电子能谱、场发射扫描电镜、接触角和微脱粘实验等测试方法对改性前后纤维表面元素组成、形貌、润湿能力以及界面粘结强度进行表征。结果表明:芳纶Ⅲ经过氨气等离子体改性后,表面含氮极性基团的含量增加,粗糙程度增大,润湿能力得到明显的改善;当氨气等离子体处理时间为15 min,功率为100 W时,芳纶Ⅲ与环氧树脂的界面粘结强度从处理前的12.9 MPa提高到18.2 MPa,与水的接触角由处理前的71.4°下降到46.8°。     

低温氨气等离子体对芳纶表面的改性

采用氨气等离子体对芳纶表面进行改性,用X-射线光电子能谱、场发射扫描电子显微镜、力学性能测试等手段对改性前后纤维表面的元素组成、形貌及其拉伸强度进行表征,并进一步通过微脱黏方法分析了等离子体处理条件对芳纶/环氧树脂复合材料界面黏结强度的影响。结果表明:芳纶经表面改性后,其表面极性官能团、表面粗糙度均有所增加,同时与环氧树脂基体的界面黏结强度明显增加。     

芳纶纤维/AFR树脂复合材料界面粘结性能的研究

为了改善芳纶纤维复合材料的界面粘结性能,合成了一种新型树脂(AFR)作为基体,以未经任何表面处理的芳纶纤维作增强材料,制备了芳纶纤维/AFR复合材料。采用测定表面能、接触角、层间剪切强度、横向拉伸性能和扫描电镜观察形貌等方法,从宏观和微观等方面研究了芳纶纤维/AFR复合材料的界面粘结性能。结果表明,AFR树脂与芳纶纤维有相近的表面能,AFR树脂溶液与芳纶纤维的接触角为42.8°,而环氧树脂(EP)与芳纶纤维的接触角为68°,说明AFR树脂对芳纶纤维的润湿性优于EP树脂;芳纶/AFR复合材料的层间剪切强度、横向拉伸强度和纵向拉伸强度分别为74.64MPa、25.34MPa和2256MPa,比芳纶/EP复合材料的相应强度分别提高了28.7%、32.5%和13.4%,其复合材料破坏面的形貌也说明芳纶纤维与AFR树脂之间的界面粘结性能较好。     

DBD等离子体改性芳纶表面的动态工艺研究

采用介质阻挡放电(DBD)空气等离子体,选择不同放电强度及处理时间对芳纶表面进行连续动态处理。通过扫描电镜以及光电子能谱仪对处理前后芳纶表面进行表征。结果表明,经DBD等离子体处理后的芳纶表面粗糙度有较大提高,浸润性显著提高,且纤维表面C元素质量分数下降超过5%,0元素质量分数约上升8%;芳纶表面的粗糙度、浸润性及含氧基团含量均随放电强度和处理时间的增加而提高。     

空气等离子体处理芳纶纤维及其与天然橡胶/乳聚丁苯橡胶的黏合性能

考察了空气等离子体处理对芳纶纤维表面结构形态的影响,研究了空气等离子体和间苯二酚-甲醛-胶乳(RFL)浸胶处理芳纶纤维与天然橡胶(NR)/乳聚丁苯橡胶(ESBR)的黏合性能,并对经处理的芳纶纤维与NR/ESBR体系的界面层作了动态力学分析。结果表明,芳纶纤维经空气等离子体处理后,表面粗糙度增大,表面积增加,结晶度减小,但处理功率过大、处理时间过长时,芳纶纤维的表面又变得比较光滑、结晶度又呈增大趋势。随着等离子体处理时间的延长,芳纶纤维与NR/ESBR的黏合性能增强,但处理时间过长时,芳纶纤维与NR/ESBR的黏合性能下降;等离子体处理芳纶纤维经RFL进一步浸胶处理后,芳纶纤维与NR/ESBR的黏合性能大幅度提高。芳纶纤维与NR/ESBR的界面存在介于高模量芳纶纤维和低模量橡胶之间的过渡层。     

Argon low‐temperature plasma modification of chopped aramid fiber and its effect on paper performance of aramid sheets

Chopped aramid fiber was modified by an argon low‐temperature plasma treatment to enhance the interfacial strength of aramid paper. The water contact angle of the aramid fiber and the tensile strength, tearing strength, and evenness of the aramid sheets were investigated under different conditions, and the parameters of the argon low‐temperature plasma modification, like gas pressure, discharge power, and discharge time, were optimized. The chemical structure and surface morphology of the fiber after plasma modification were characterized by X‐ray photoelectron spectroscopy, atomic force microscopy, and scanning electron microscopy. The strengthening mechanism of aramid paper by low‐temperature plasma modification was also studied. It was found that the argon low‐temperature plasma treatment introduced some new polar groups onto the fiber surface and increased the fiber surface wettability and roughness. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45215.     

The effect of atmospheric‐pressure air plasma discharge power on adhesive properties of aramid fibers

After exposure to the atmospheric‐pressure air plasma at different discharge powers, the adhesion characteristics of Twaron aramid fibers were investigated. For the 12 s‐300 W plasma treatment, the interlaminar shear strength of Twaron fiber reinforced thermoplastic poly(phthalazinone ether sulfone ketone) was increased from 46.0 to 61.7 MPa by 34.1%, and the diffusion of water molecule into the resulting composites was proved to be effectively prevented. These results showed that surface adhesive properties of the plasma‐treated aramid fibers were improved. At the power level of 300 W, X‐ray photoelectron spectroscopy analysis revealed the increases in concentrations of oxygen and nitrogen polar groups on the fiber surface, and atomic force microscopy observations led to the conclusion that the fiber surface morphology was changed and the surface roughness was greatly increased. These new polar and irregular surface structures accounted for the better adhesion between the fiber and the matrix, while due to the reasonability of this discharge power level applied to the surface modification, the measured fiber tensile strength only decreased by 2.0%. POLYM. COMPOS., 37:620–626, 2016. © 2014 Society of Plastics Engineers     

Wetting and adhesion behavior of armos fibers after dielectric barrier discharge plasma treatment

To investigate the influence of atmospheric plasma treatment on aramid fiber wetting and adhesion behavior, an air dielectric barrier discharge (DBD) was applied to the Armos aramid fiber surface at different discharge power densities. Dynamic contact angle analysis indicated that the total surface free energy was increased from 49.6 to 68.3 mJ/m 2 , an increment of 37.7%, whereas the single-fiber tensile strength testing showed that the mechanical properties of the Armos fibers were almost unaffected. With the enhancement of fiber surface wettability, the interlaminar shear strength, which was used to determine the interfacial adhesion in Armos-fiber-reinforced thermoplastic poly(phthalazinone ether sulfone ketone) composites, increased by 17.2% to 71.4 MPa. Scanning electron microscopy photos showed that the predominant failure mode of the composites changed from interface failure to matrix and/or fiber failure after the plasma treatment. Taken together, these results suggest that the air DBD plasma was an effective technique for improving the surface and interfacial performance of the Armos fibers without damaging their bulk properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

常压等离子体改善合成纤维吸湿性的研究

用氦气作为等离子体的气体源、对涤纶、锦纶6、高强度聚乙烯纤维,Twaron 1000芳纶4种合成纤维进行常压等离子体处理,改善纤维的吸湿性能。结果表明:常压等离子体处理,对涤纶和锦纶6的表面有一定的刻蚀作用,但对高强度聚乙烯纤维、Twaron 1000芳纶的表面没有明显影响;经常压等离子体处理后,合成纤维表面氧、氮有所增加,吸湿性能得到提高,强度没有显著变化。     

介质阻挡放电在芳纶表面改性中的应用

综述了介质阻挡放电应用于芳纶表面改性研究的最新进展;介绍了介质阻挡放电的机理、特点以及国内主要的介质阻挡放电等离子体的设备;阐述了介质阻挡放电对芳纶亲水性能和粘结性能等表面性能的改善。指出芳纶等离子体表面改性的时间效应限制了其广泛应用,应进一步加强纤维表面等离子体改性的机理研究。     

RETRACTED ARTICLE: Surface modification of aramid fibers with novel chemical approach

Friedel–Crafts Reaction as a simple and convenient approach to the surface modification of aramid fiber was introduced in this paper. Epoxy chloropropane was chosen as the treatment reagent to modify aramid fibers surface via Graft reaction. After the modification, the interfacial properties of aramid/epoxy composites were investigated by the single fiber pull-out test (SFP), and the mechanical properties of aramid fibers were investigated by the tensile strength test. The results showed that the interfacial shear strength (IFSS) value of aramid/epoxy composites was enhanced by about 50%, and the tensile strength of aramid fibers had no obvious damage. The crystalline state of aramid fibers was determined by X-ray diffraction instrument (XRD), and the results showed that there were not any distinct crystal type varieties. The surface elements of aramid fibers were determined by X-ray photoelectron spectroscopy (XPS), the analysis of which showed that the oxygen/carbon ratio of aramid fiber surface increased obviously. The possible changes of the chemical structure of aramid fibers were investigated via Fourier transform infrared spectrum (FTIR), and the analysis of which showed that the epoxy functional groups were grafted into the molecule structure of aramid fibers. The surface morphology of aramid fibers was analyzed by Scanning electron microscope (SEM), and the SEM results showed that the physical structure of aramid fibers was not etched or damaged obviously. The surface energy of aramid fibers was investigated via the dynamic capillary method, and the results showed that the surface energy was enhanced by 31.5%, and then the wettability degree of aramid fiber surface was enhanced obviously too. All of the results indicated that this novel chemical modification approach not only can improve the interfacial bonding strength of aramid/epoxy composites remarkably, but also have no negative influence on the intrinsic tensile strength of aramid fibers.