响应面方法分析代谢产物对类人胶原蛋白表达的影响

Recombinant Escherichia coli BL21 is used to produce human-like collagen. The key constituents of media are optimized using response surface methodology (RSM). Before thermal induction, the highest biomass production and the lowest production of some hazardous by-products, especially acetic acid, were obtained in the media containing 0.085 mol∙L1 glucose and 0.019 mol∙L1 nitrogen (carbon-nitrogen ratio, 4.47︰1). After thermal induction, when the concentrations of glucose and nitrogen in the media were 0.065 mol∙L1 and 0.017 mol∙L1, respectively (carbon-nitrogen ratio, 3.82︰1), the productivity of human-like collagen per cell was the highest while that of acetic acid was the lowest. The extended analysis showed that the production of lactic acid and propionic acid increased while that of some intermediate acids of the tricarboxylic acid cycle decreased if the dose of glucose in-creased.     

氨改性的介孔二氧化硅的直接合成和CO2吸附

Amine-functionalized mesoporous silica was prepared by using lauric acid and N-stearoyl-l-glutamic acid as structure directing agents via the SN+-I mechanism and applied to CO2 adsorption at room temperature. With γ-aminopropyltriethoxysilane as co-structure directing agent and due to the direct electrostatic interaction with anionic surfactant, most of the amino groups were uniformly distributed at the inner surface of pores and the performance was stable. The amine-functionalized mesoporous silica was characterized by Fourier transform infrared spectrometer, X-ray diffraction, nitrogen physisorption and thermogravimetric analysis. The CO2 adsorption capacity was measured by digital recording balance. At the room temperature and under the atmospheric pres-sure, the adsorption capacity of LAA-AMS-0.2 for CO2 and N2 is 1.40 mmol•g1 and 0.03 mmol•g1, respectively, indicating high separation coefficient of CO2/N2.     

用CuO/A12O3/堇青石催化剂选择性催化还原脱硝的实验和动力学研究

The CuO/γ-Al2O3/cordierite catalyst, after being sulfated by sulfur dioxide (SO2) at 673 K, exhibits high activities for selective catalytic reduction (SCR) of nitrogen oxide (NO) with ammonia (NH3) at 573-723 K. The intrinsic kinetics of SCR of NO with NH3 over CuO/γ-Al2O3/cordierite catalyst has been measured in a fixed-bed reactor in the absence of internal and external diffusions. The experimental results show that the reaction rate can be quantified by a first-order expression with activation energy of 94.01 kJ•mol1 and the corresponding pre-exponential factor of 3.39×108 cm3•g1•s1 when NH3 is excessive. However, when NH3 is not enough, an Eley-Rideal kinetic model based on experimental data is derived with Ea of 105.79 kJ•mol1, the corresponding A of 2.94×109 cm3•g1•s1, heat of adsorption ΔHads of 87.90 kJ•mol1 and the corresponding Aads of 9.24 cm3•mol1. The intrinsic kinetic model obtained was incorporated in a 3D mathematical model of monolithic reactor, and the agreement of the prediction with experimental data indicates that the present kinetic model is adequate for the reactor design and engineering scale-up.     

硫酸铁改性颗粒活性氧化铝除氟的等温线研究

The adsorption equilibrium of a fluoride solution on 1-2 mm granular activated alumina modified by Fe2(SO4)3 solution was investigated. The experiments were conducted using a wide range of initial fluoride concentrations (0.5 to 180 mg•L1 at pH ~7.0) and an adsorbent dose of 1.0 g•L1. The application of Langmuir and Freundlich adsorption isotherm models (linear and nonlinear forms) generally showed that a single Langmuir or Freundlich equation cannot fit the entire concentration gap. Experimental data on low equilibrium concentrations (0.1 to 5.0 mg•L1) was in line with both Langmuir and Freundlich isotherm models, whereas that of high equilibrium concentrations (5.0 to 150 mg•L1) was more in line with the Freundlich isotherm model. A new Langmuir- Freundlich function was used for the entire concentration gap, as well as for low and high concentrations.     

PDMS/陶瓷复合膜用于正丁醇-水体系的渗透汽化分离

Pervaporation has attracted considerable interest owing to its potential application in recovering biobutanol from biomass acetone-butanol-ethanol (ABE) fermentation broth. In this study, butanol was recovered from its aqueous solution using a polydimethylsiloxane (PDMS)/ceramic composite pervaporation membrane. The effects of operating temperature, feed concentration, feed flow rate and operating time on the membrane pervaporation per-formance were investigated. It was found that with the increase of temperature or butanol concentration in the feed, the total flux through the membrane increased while the separation factor decreased slightly. As the feed flow rate increased, the total flux increased gradually while the separation factor changed little. At 40 C and 1% (by mass) butanol in the feed, the total flux and separation factor of the membrane reached 457.4 g•m2•h1 and 26.1, respec-tively. The membrane with high flux is suitable for recovering butanol from ABE fermentation broth.     

D318阴离子交换树脂对铼（VII）的吸附

The adsorption and mechanism of Re(VII) on resin D318 were studied using chemical methods and IR spectrometry. At pH 5.2, the static and dynamic saturation adsorption capacities were 351.4 and 366.5 mg&;#8226;g&;#61485;1, respectively. The adsorption behavior obeyed the Freundlich empirical equation and the adsorption rate constant k298 was 6.37×10&;#61485;4 s&;#61485;1. The desorption percentage was up to 99.7% when 2.0 mol&;#8226;L&;#61485;1 KSCN was used for dynamic desorption.     

P507溶于煤油作为载体的一种新型分散组合液膜对Eu3+的分离

The separation of Eu3+ is studied with a dispersion combined liquid membrane (DCLM), in which polyvinylidene fluoride membrane (PVDF) is used as the liquid membrane support, dispersion solution containing HCl solution as the stripping solution, and 2-ethyl hexyl phosphonic acid-mono-2-ethyl hexyl ester (P507) dissolved in kerosene as the membrane solution. The effects of pH value, initial concentration of Eu3+ and different ionic strength in the feed phase, volume ratio of membrane solution to stripping solution, concentration of HCl solution, concentration of carrier, different stripping agents in the dispersion phase on the separation are investigated. The optimum condition for separation of Eu3+ is that concentration of HCl solution is 4.0 mol•L1, concentration of carrier is 0.16 mol•L1, and volume ratio of membrane solution to stripping solution is 30︰30 in the dispersion phase, and pH value is 4.2 in the feed phase. The ionic strength has no significant effect on separation of Eu3+. Under the optimum condition, when the initial concentration of Eu3+ is 0.8×104 mol•L1, the separation percentage of Eu3+ is 95.3% during the separation time of 130 min. The kinetic equation is developed in terms of the law of mass diffusion and the theory of interface chemistry. The diffusion coefficient of Eu3+ in the membrane and the thickness of diffusion layer between feed phase and membrane phase are obtained and their values are 1.48×107 m2•s1 and 36.6 μm, respectively. The results obtained are in good agreement with literature data.     

刺芹侧耳多功能过氧化物酶的纯化与鉴定

A versatile peroxidase (VP-Peco60-7) was generated and purified from the liquid culture of Pleurotus eryngii. The purification procedure included ammonium sulfate precipitation, ion exchange chromatography, and gel chromatography. The molecular weight and isoelectric point (pI) of VP-Peco60-7 were determined to be approximately 40 kDa and 4.1, respectively. By N-terminal sequence determination and peptide mapping analysis, VP-Peco60-7 was found to be similar to the versatile peroxidase isoenzyme VPL1, which was previously isolated from liquid cultures of the same species. However, the molecular weight and pI of VP-Peco60-7 were different from those of versatile peroxidases of liquid cultures, implying that the VP-Peco60-7 in this study is of a novel type. With 2,2′-azino-bis-(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) as a substrate, the maximal enzyme activity was obtained at 50 °C and pH 3.0. The catalysis of ABTS by VP-Peco60-7 was expressed by the Michaelis-Menten equation. At 50 °C and pH 3.0, the maxi-mum velocity (Vmax) was 188.68 U•mg1 and the michaelis constant (Km) was 203.09 mmol•L1.     

以正硅酸乙酯和1,2-二(三乙氧基硅基)乙烷为前驱体制备微孔SiO2复合膜及其气体分离性能

This paper reports on ¬¬¬a new microporous composite silica membrane prepared via acid-catalyzed polymeric route of sol-gel method with tetraethylorthosilicate (TEOS) and a bridged silsesquioxane [1, 2-bis(triethoxysilyl)ethane, BTESE] as precursors. A stable nano-sized composite silica sol with a mean volume size of ~5 nm was synthesized. A 150 nm-thick defect-free composite silica membrane was deposited on disk support consisting of macroporous α-Al2O3 and mesoporous γ-Al2O3 intermediate layer by using dip-coating ap-proach, followed by calcination under pure nitrogen atmosphere. The composite silica membranes exhibit molecular sieve properties for small gases like H2, CO2, O2, N2, CH4 and SF6 with hydrogen permeances in the range of (1-4)107 mol•m2•s1•Pa1 (measured at 200 C, 3.0×105 Pa). With respect to the membrane calcined at 500 C, it is found that the permselectivities of H2 (0.289 nm) with respect to N2 (0.365 nm), CH4 (0.384 nm) and SF6 (0.55 nm) are 22.9, 42 and >1000, respectively, which are all much higher than the corresponding Knudsen values (H2/N2 3.7, H2/CH4 2.8, and H2/SF6 8.5).     

超临界萃取技术结合超声强化技术提取鹿茸中性激素和IGF-1

Supercritical CO2 (SC-CO2) extraction technology and ultrasonic technology were used to extract two active sex hormones, estradiol and progesterone, and insulin-like growth factor-1 (IGF-1) from antler velvet. The effects of SC-CO2 extraction condition on the extraction yield and content of sex hormones, the ultrasonic extraction condition on the content of IGF-1 and the SC-CO2 extraction condition on the activity remaining of IGF-1 were studied. The optimal conditions were obtained. The experimental results showed that, in presence of 75% ethanol as the co-solvent, the mean yield and content of estradiol and progesterone were 87.67 pg•g－1 and 1224.10 pg•g－1, 12.38 ng•g－1 and 354.06 ng•g－1, respectively, with extraction pressure of 30 MPa, temperature of 35°C, extraction time of 30 min and CO2 consumption of 15 L•g－1 at the flow rate of 2.0 L•min－1. The highest content of IGF-1 was 7425.75 ng•g－1 antler velvet residue, when the pH10 ammonia-ammonium chloride buffer solution was used as the solvent, the ratio of solvent to sample was 20/1 (volume/mass), the extraction temperature was 0-35°C, and the ex-traction time was 4×15 min. Under these conditions, 93.68% activity remaining of IGF-1 in the residue was ob-tained, while little IGF-1 activity exists in traditional residue. The experimental results indicate that the technology of SC-CO2 with co-solvent is of advantage for getting high content sexual hormones and keeping high activity of IGF-1 in the residue, which can not be achieved by traditional extraction methods.     

六碳糖和五碳糖同步糖化与共发酵的数学模型

Reliable production of biofuels and specifically bioethanol has attracted a significant amount of re-search recently.Within this context,this study deals with dynamic simulation of bioethanol production processes and in particular aims at developing a mathematical model for describing simultaneous saccharification and co-fermentation (SSCF) of C6 and C5 sugars.The model is constructed by combining existing mathematical mod-els for enzymatic hydrolysis and co-fermentation.An inhibition of ethanol on cellulose conversion is introduced in order to increase the reliability.The mathematical model for the SSCF is verified by comparing the model predic-tions with experimental data obtained from the ethanol production based on kraft paper mill sludge.When fitting the model to the data,only the yield coefficients for glucose and xylose metabolism were fine-tuned,which were found to be 0.43 g·g-1 (ethanol/glucose) and 0.35 g·g-1 (ethanol/xylose) respectively.These promising validation results encourage further model application to evaluate different process configurations for lignocellulosic bioetha-nol technology.     

L-半胱氨酸浓度对氧化还原电位和生物产氢过程的影响(英文)

The effects of L-cysteine concentration on biohydrogen production by Enterobacterium Bacterium M580 were investigated in batch cultivation.The experimental results showed that L-cysteine could enhance the cell growth,hydrogen production rate and hydrogen yield when its concentration was less than 500 mg·L-1,while it had negative effects when its concentration was higher than 500 mg·L-1.The hydrogen production was the highest 1.29 mol·mol-1(H2/glucose) when 300 mg·L-1L-cysteine was added into the culture,and the yield was 9.4% higher than that in the control.The oxidation-reduction potential(ORP) ,which was influenced by L-cysteine,also affected hydrogen production.The ORP values were in the range-300 mV to-150 mV when the L-cysteine concentration was higher than 500 mg·L-1.Although the ORP in this range was favorable for hydrogen production,it was not suitable for the biomass growth.Hence,less hydrogen was produced.When the L-cysteine concentration was lower than 500 mg·L-1,the ORP was more suitable for both biomass growth and hydrogen production.In addition,at least 91%glucose was consumed when L-cysteine was added to the culture media,compared to the 97.37% consumption without L-cysteine added.     

大豆秸秆酶水解及L-乳酸发酵

用纤维素酶对氨预处理后的大豆秸秆进行酶水解,利用纤维素酶的作用使纤维素、半纤维素水解为可溶性糖,继而研究了用干酪乳杆菌及清酒乳杆菌进行L-乳酸发酵,通过微生物发酵将生成的可溶性糖转化为用于生产具有可生物降解性的聚乳酸塑料的原料乳酸,实现可再生资源的充分利用.结果表明,实验条件下,5%的大豆秸秆经酶水解后,还原糖浓度为242.25 mg•g^-1,纤维素糖化率为51.22%.清酒乳杆菌、干酪乳杆菌及该两种混合菌种发酵酶解液所得L-乳酸的转化率分别为 48.27%、56.42%和71.05%.     

水热合成二硫化钼纳米片及在锂离子电池中的应用(英文)

Molybdenum disulfide nanoflakes were synthesized by a simple hydrothermal process using sodium molybdate and thiourea as reactants at a relatively low temperature. X-ray diffraction(XRD) and transmission elec-tron microscopy(TEM) indicate that the samples have the structure of 2H-MoS2 and the morphology of nanoflakes with the average thickness around 5-10 nm. The results of electrochemical properties indicate that the morphology and size of MoS2 particles have effects on their capacity when they are used as the anode for lithium ion battery. The as-prepared MoS2 samples have high reversible discharge capacity up to 994.6 mA·h·g-1 for the MoS2-1 elec-trode and 930.1 mA·h·g-1 for the MoS2-2 electrode and show excellent cycling performances. The MoS2-1 electrode has a better cycling stability than the MoS2-2 electrode due to their difference in the uniformity of the samples.     

重组尿苷磷酸化酶的诱导及其在嘧啶核苷生物合成中的应用

Recombinant Escherichia coli pUDP,which overexpressed uridine phosphorylase(UPase),was constructed.0.5 mmol·L 1lactose had a similar induction effect as the commonly used inducer IPTG during 2.5-5.5 h of cell growth.The lactose-induced UPase was stable at 50°C.Wet cells of pUDP was used as catalyst to biosynthesize 5-fluorouridine from 30 mmol·L 1uridine and 5-fluorouracil in phosphate buffer(pH 7.0)catalyzed at 50°C for 1.5 h and the yield of 5-fluorouridine was higher than 68%.Under the optimum reaction conditions for production of 5-fluorouridine,5-methyluridine and azauridine were synthesized from uridine by pUDP,the yield was 61.7%and 47.2%respectively.Deoxynucleosides were also synthesized by pUDP,but the yield was only about 20%.     

海藻酸镧颗粒除氟研究：吸附剂物性和吸附机理

Lanthanum alginate bead is a new, highly active adsorbent. In the present study, we investigated its ad- sorption performance and its adsorption mechanism. The adsorption isotherm for fluoride onto lanthanum alginate b ead fits the Langmuir model well, and the maximum adsorption capacity is 197.2 mg·g-1. X-ray diffraction shows the amorphous nature of lanthanum alginate bead, which allows for better accessibility to fluoride and thus better activity. Infrared spectra of lanthanum alginate bead before and after adsorption confirm its stable skeletal structure. Scanning electron microscopy shows that the dense surface structure of the adsorbent appear cracks after adsorption. T he adsorption mechanism of lanthanum alginate bead is considered as an ion exchange between F- and Cl- or OH-, as verified from the adsorbent and the solution by pH effect, energy dispersive X-ray, and ion chromatography.     

絮凝酵母SPSC01酒精连续发酵并联产酵母工艺过程

引　言随着以石油为代表的矿物质资源储量的日益减少及大量开发利用导致环境污染的加剧,以植物光合作用产生的糖质、淀粉质和木质纤维素类可再生资源为原料,采用微生物发酵法生产的酒精作为替代能源,正越来越引起世界各国的高度重视.然而,在现有条件下,以淀粉质原料生产燃料酒精的生产　　Receiveddate:2 0 0 3 -12 -10 .Correspondingauthor:ZILihan .E -mail:zilihan @163 com　成本还难以同成品油的价格相竞争,在相当大的程度上依赖政府的优惠政策和直接财政补贴.因此,提高原料的综合利用程度,开发高附加值副产品,具有十分重要的意义…     

皮胶原纤维负载钦对核工业废水中铀的去除(英文)

Effective recovery of UO2+2 from wastewater is essential for nuclear fuel industry and related industries.In this study,a novel adsorbent was prepared by loading titanium(Ti4+) onto collagen fiber(TICF),and its physical and chemical properties as well as adsorption to UO2+2 in nuclear fuel industrial wastewater were investigated.It is found that TICF can effectively recover UO2+2 from the wastewater with excellent adsorption capacity.The adsorption capacity is 0.62 mmol·g-1 at 303 K and pH 5.0 when the initial concentration of UO2+2 is 1.50 mmol·L-1.The adsorption isotherms can be described by the Langmuir equation and the adsorption capacity increases with temperature.The effect of co-existed F on the adsorption capacity for UO2+2 is significant,which can be eliminated by adding aluminum ions as complexing agent,while the other co-existed ions in the solutions,including HCO-3,Cl-,NO-3,Ca2+,Mg2+ and Cu2+,have little effect on the adsorption capacity for UO2+2.The saturated TICF after UO2+2 adsorption can be regenerated by using 0.2 mol·L-1 nitrate(HNO-3) as desorption agent,and the TICF can be reused at least three times.Thus the TICF is a new and effective adsorbent for the recovery of UO2+2 from the wastewater.