Magnetic field enhanced radio frequency ion source and its application for Si-incorporation diamond-like carbon film preparation

Various ion sources are key components to prepare functional coatings,such as diamond-like carbon(DLC)films.In this article,we present our trying of surface modification on basis of Si-incorporation diamond-like carbon(Si-DLC)produced by a magnetic field enhanced radio frequency ion source,which is established to get high density plasma with the help of magnetic field.Under proper deposition process,a contact angle of 111°hydrophobic surface was achieved without any surface patterning,where nanostructure SiC grains appeared within the amorphous microstructure.The surface property was influenced by ion flow parameters as well as the resultant surface microstructure.The magnetic field enhanced radio frequency ion source developed in this paper was useful for protective film applications.     

重离子径迹模板中组装半导体CdS一维纳米材料

用重离子辐照的聚碳酸酯为模板,采用电化学沉积法制备了半导体CdS纳米线和纳米管.通过选用不同蚀刻时间的模板,得到了直径20～100 nm、长度20～30 μm范围、粗细均匀且具有纤维锌矿结构的CdS纳米线与纳米管.利用扫描电子显微镜(SEM)、X射线衍射(XRD)和透射电子显微镜(TEM)对CdS纳米线与管的形貌和晶体结构特征进行了表征.     

擦拭样品中铀微粒甄别技术的研究

基于裂变径迹原理对擦拭样品中微米量级铀微粒筛选技术进行了研究.研究内容包括擦拭样品与载体分离、样品在裂变径迹片上沉积、样品辐照以及化学刻蚀、铀微粒筛选等.文章中对各实验环节进行细致描述和讨论.研究发现:(1)以无尘滤纸、脱脂棉、Texwipe牌TX304型棉布为擦拭载体的样品经过400℃ 6 h灰化为较好的分离方法;(2)经热中子辐照和化学刻蚀后裂变径迹主要呈星状和坑状.其中235U含量高的微粒对应于坑状径迹,含量低的微粒对应于星状径迹;(3)采用新的定位方法能够筛选出铀微粒.     

放射治疗中肿瘤靶区勾画的主观差异性分析

为了解医生的主观因素在肿瘤靶区(GTV)勾画中产生差异性并分析其原因,对肿瘤处在身体不同部位的12例病人的CT定位图像,组织了来自放射治疗和影像诊断的6位医师进行了GTV勾画,计算病人GTV的体积值及其变化范围,比较两个学科和两次勾画所产生的差异性.结果表明,9位病人GTV体积最大值/最小值比值＜2,3位病人的项比值＞2;16%的体积值对体积平均数的变动范围＞±25%.在已知影响准确性的重要客观因素一致的条件下,造成差异性的主要原因是医生间学科的不同,影像科医生比放疗科医生的变异性小、准确性高.因此,在确定GTV时,对于因主诊医生主观因素产生的误差要引起重视,放射治疗医生加强影像诊断学知识学习与协作,建立、完善并认真执行相关的QA与QC规程是解决问题的主要方法.     

低能氮离子注入香菇生物学效应的研究

本文用能量为 15 keV,而注量不同的氮离子注入对武香一号香菇进行诱变,分析了不同注量下菌丝长速,菌丝生物量以及多糖含量的变化,对该低能离子与微生物间的作用规律进行了初步探索,为进一步筛选出多糖高产菌株提供前提.实验结果表明菌丝长速,菌丝生物量及多糖含量随不同注量的变化情况基本遵循"马鞍型曲线".注量小时菌丝日均长速较快,随着注量的增大,菌丝日均长速呈下降趋势,但在1.5×1016cm-2附近,菌丝长速有短暂回升.在注量较小时,随着注量的增加,菌丝生物量及多糖含量先升高后降低,注量为4×1015cm-2时,两者均达到最大值,而后会出现小的波动,注量增加到1.5×1016cm-2时,菌丝生物量及多糖含量又会达到-个较大的峰值.通过发酵动力学分析,研究了香菇液体菌种培养过程中菌丝球数量及形态、摇瓶总重、pH值、多糖含量等指标的变化情况,绘制该菌发酵产糖的过程曲线,这将为诱变前后液体发酵过程的控制提供参数.     

放疗后早期肿瘤组织内99Tcm-rh-Annexin Ⅴ分布与Survivin、Caspase-3蛋白表达的相关性研究

采用99Tcm-rh-AnnexinⅤ作为核素凋亡显像示踪剂,观察小鼠放疗后早期肿瘤组织内Survivin、Caspase-3蛋白表达。结果显示,放疗组肿瘤组织内99Tcm-rh-AnnexinⅤ分布、TUNEL检测阳性细胞数及Caspase-3蛋白表达均明显多于对照组,Survivin蛋白表达A组明显高于B组,差异均存在显著性（P均<0.01）。相关性研究表明,肿瘤组织的放射性摄取与TUNEL阳性细胞数呈明显正相关（r=0.942,P=0.000）;肿瘤组织内Survivin蛋白表达与Caspase-3蛋白表达呈明显负相关（r=-0.836,P=0.000）。肿瘤组织内99Tcm-Annexin Ⅴ分布与Caspase-3蛋白表达呈明显正相关（r=0.948,P=0.000）,与Survivin蛋白表达呈明显负相关（r=-0.819,P<0.01）。以上结果提示,肿瘤组织内99Tcm-rh-AnnexinⅤ的分布可以反映放疗后早期肿瘤组织细胞凋亡的状况以及凋亡调控蛋白Survivin、Caspase-3表达水平的变化。     

三代核电自主化依托项目的工程建造管理模式

2007年7月24日,国家核电技术公司、三门核电有限公司、山东核电有限公司、中国技术进出口总公司,与美国西屋联合体及分包商分别签订了第三代核电自主化依托项目4个机组的核岛设计及部分主设备采购合同;国家核电技术     

国外最新消息

伊朗总统宣布已开始安装6000台新离心机伊朗总统艾哈迈迪·内贾德2008年4月8日宣布,伊朗已开始在纳坦兹铀浓缩基地安装6000台新的离心机。(编译自法新社2008年4月8日报道)     

高压氘氚气氛下不锈钢吸附氚的初步研究

本工作对于氚在不锈钢表面的吸附和解吸行为进行了初步研究.样品在n(D)∶n(T)=1∶1,230℃时,15 MPa下恒温8 h后,接着在27 MPa下恒温6 h的情况下进行了氚的吸附,测量了室温下和加热到1173 K时的解吸氚量和总吸附量.其结果如下:不锈钢的总吸附氚量是857.4 MBq·cm-2,不锈钢的解吸氚量是722.2 MBq·cm-2;在本实验的条件下,在室温和加热条件下,不锈钢所释放的氚中,化学成分主要是HTO和HT两部分,大部分以HT形式存在;不锈钢的自由氚占吸附总氚量的7.34%;不锈钢的热解吸谱存在三个解吸峰,其解吸温度分别为439、530和843K.     

Continuous compositional spread investigation of SiC-based thin films prepared by MW-ECR plasma enhanced magnetron co-sputtering

A kind of combinatorial material methodology,also known as continuous compositional spread method,was employed to investigate the relationship between the optical band gap and composition of SiC thin films.A wide range of SixCy thin films with different carbon contents have been successfully deposited in a single deposition by carefully arranging the sample position on the substrate holder.The films were characterized by surface profiler,x-ray photoelectron spectroscopy,ultraviolet-visible spectroscopy,fourier transform infrared spectroscopy and Raman spectroscopy.The carbon content y increases linearly from 0.28 to 0.72 while the sample position changed from 85 to 175 mm,the optical band gap changed between 1.27 and 1.99 eV,the maximum value corresponded to the stoichiometric SiC sample at the position of 130 mm,which has the highest Si?C bond density of 11.7×10^22 cm^-3.The C poor and C rich SixCy samples with y value less and larger than 0.5 were obtained while samples deviated from the position 130 mm,the optical band gap decreased with the Si?C bond density.     

Sorption methods of separating barium and radium,aluminum and gallum,and zirconium and hafnium

Chromatographic methods of separating elements with very similar properties have now been developed. However, a number of these methods are difficult to use industrially as their throughput is low. The efficiency of chromatographic separation methods could be increased considerably by using appropriate complex formers, which decrease the effective concentration of the ions being separated, and,in the first approximation, this is equivalent to a decrease in the amount of elements being separated. The difference in the formation constants of the complex compounds increases the separation coefficient. By investigating chromatographic separation with the use of various complex formers, we found the optimal conditions for separating barium and radium, zirconium and hafnium, and aluminum and gallium. The throughput of these methods, with respect to the macroelement was 15–60 kg/hr per m² of column cross section.     

医源性电离辐射损伤及其生物医学防护

随着核与辐射技术在医学检查、诊断和治疗领域运用的增加,世界范围受照人群不断增多,医源性辐射已成为人类最主要的人工辐射来源之一。医疗机构和个人在选择利用放射手段获取诊断和治疗利益的同时,需要注意和防护伴随的辐射损伤效应。本文介绍了医源性辐射及其危害、机体组织的辐射损伤特性和类型、辐射生物效应分子及效应调节研究的进展,简要概述目前临床已经使用或最具应用潜力的辐射防护策略。     

Distribution and Fixation of Cesium and Strontium in Zeolite A and Chabazite

The selective removal and fixation of Cs and Sr have been studied in zeolite A and chabazite. Cesium ion was preferentially distributed into chabazite with a high distribution coefficient (K _Cs>10³ cm³·g^?1) in the presence of NaCl (10^?1 mol·dm^?3). The K _Sr values for zeolite A attained about 10³ cm³·g^?1 in the pH range of 8～10, and they gradually decreased with an decrease in pH.

The initial rate of Cs adsorption was fairly fast in chabazite, and the adsorption ratio reached almost 100% within a few hours. The adsorption ratio of Sr in binderless A zeolite reached almost 100% after 15 h. The adsorption of Cs and Sr on these zeolites was followed by Langmuir-type isotherm. Cesium forms of these zeolites recrystallized to pollucite (CsAlSi₂O₆) above 900°C for zeolite A and above 1,200°C for chabazite. As for Sr forms, these zeolites changed to SrAl₂Si₂O₆ above 900°C.

These recrystallized phases were suitable hosts for the immobilization of Cs and Sr in the nuclear waste solutions.     

清洁解控和退役若干动向与新发展

对国际辐射防护协会第 1 0届大会 ( IRPA-1 0 )涉及的清洁解控和退役问题作了论述 ,包括排除、豁免、清洁解控和废物最少化 ;退役工程技术的发展 ,包括去污技术、切割解体技术、探测技术 ;介绍了一个研究堆退役例子和加速器退役 ;最后 ,还论及了退役中受关注的一些问题 ,如 :石墨废物、混凝土废物、重水堆退役的氚防护、退役时间和退役废物量等。     

Plastic and dissipated work and stored energy

This paper depicts one theoretical and experimental method to take into account the energy phenomena, associated with the elasto—plastic deformation process, during the elaboration of behaviour laws. The energy balance definition is examined in order to relate the stored energy of cold work to the hardening state variables. Two experimental approaches are used to study the evolution of the energy balance. The first one uses microcalorimetric technique and the second infrared technique. Several industrial metallic materials are studied by both approaches. Energy data are used to control the validity domain of the classical behaviour laws and to elaborate new more appropriate ones. Therefore, the hardening parameters cannot be identified with the thermodynamical forces. The use of energy considerations allows the definition of new thermodynamical forces and state variables, in the case of isotropic or kinematical hardening.     

全国核与辐射安全监管信息系统的研究和建议

文章简要介绍了全国核与辐射安全监管信息系统的前期规划建设情况,包括基本建设内容、系统总体架构、以及工作中发现的影响和制约工作开展的主要问题,并提出了建议。     

Development and diversity and defense-in-depth application of ABWR feedwater pump and controller model

This work developed an advanced boiling water reactor (ABWR) feedwater pump and controller model, which was incorporated into Personal Computer Transient Analyzer (PCTran)-ABWR, a nuclear power plant simulation code. The feedwater pump model includes three turbine-driven feedwater pumps and one motor-driven feedwater pump. The feedwater controller includes a one-element/three-element water level controller and a specific feedwater speed controller for each feedwater pump. The performance tests, including step change of dome pressure, feedwater pumps transfer, inadvertent closure of all turbine control valves, and one feedwater pump trip at 100% power, demonstrate the feasibility of dynamic response of stand-alone model and incorporated model. Furthermore, a diversity and defense-in-depth analysis is performed to demonstrate the feasibility for motor-driven feedwater pump as an emergency core cooling system (ECCS) automatic diverse back-up. In Lungmen nuclear power plant (NPP), a diverse manual initiation means for the high pressure core flooder (HPCF) loop C is designed as the back-up of digitalized engineered safety features actuation system (ESFAS). If the motor-driven feedwater pump (MDFWP) can be an automatic digital diverse back-up for ESFAS, Lungmen NPP would be more robust to defend against software common-cause failure (CCF).     

Construction and operational experience with small and medium power reactors and expected improvements

Past experience with small and medium power reactors (SMPRs) in the areas of construction and operation is examined in this paper. Current development of SMPRs focuses on passive safety features; larger design and safety margins; reduction of construction periods through simplification, modularization and increased shop fabrication.