Selecting optimal monitoring site locations for peak ambient particulate material concentrations using the MM5-CAMx4 numerical modelling system

Installation of temporary or long term monitoring sites is expensive, so it is important to rationally identify potential locations that will achieve the requirements of regional air quality management strategies. A simple, but effective, numerical approach to selecting ambient particulate matter (PM) monitoring site locations has therefore been developed using the MM5-CAMx4 air pollution dispersion modelling system. A new method, ‘site efficiency,’ was developed to assess the ability of any monitoring site to provide peak ambient air pollution concentrations that are representative of the urban area. ‘Site efficiency’ varies from 0 to 100%, with the latter representing the most representative site location for monitoring peak PM concentrations. Four heavy pollution episodes in Christchurch (New Zealand) during winter 2005, representing 4 different aerosol dispersion patterns, were used to develop and test this site assessment technique. Evaluation of the efficiency of monitoring sites was undertaken for night and morning aerosol peaks for 4 different particulate material (PM) spatial patterns. The results demonstrate that the existing long term monitoring site at Coles Place is quite well located, with a site efficiency value of 57.8%. A temporary ambient PM monitoring site (operating during winter 2006) showed a lower ability to capture night and morning peak aerosol concentrations. Evaluation of multiple site locations used during an extensive field campaign in Christchurch (New Zealand) in 2000 indicated that the maximum efficiency achieved by any site in the city would be 60-65%, while the efficiency of a virtual background site is calculated to be about 7%. This method of assessing the appropriateness of any potential monitoring site can be used to optimize monitoring site locations for any air pollution measurement programme.     

Elevated concentrations of 1-hydroxypyrene in schoolchildren during winter in Christchurch, New Zealand

Particulate air pollution is significantly elevated during the winter in Christchurch, New Zealand, largely attributable to use of wood burners for domestic home heating, topography, and meteorological conditions. Polycyclic aromatic hydrocarbons (PAHs) are a key component of airborne particulate matter (PM) and urinary 1-hydroxypyrene (1-OHP) has previously been used to assess exposure of people to PAHs. We examined urinary 1-OHP in Christchurch male non-smoking schoolchildren (12-18 yr) on two occasions after high pollution events (48 and 72 microg PM(10)/m(3) 24-h average) and two occasions during periods of low pollution (19 and 12 microg PM(10)/m(3)). Concentrations of urinary 1-OHP were significantly elevated in the students during high pollution events (median (mean+/-SD) 0.043 (0.051+/-0.032) and 0.042 (0.060+/-0.092) micromol OHP/mol creatinine respectively) compared with low pollution periods (median (mean+/-SD) 0.019 (0.026+/-0.032) and 0.025 (0.028+/-0.018) micromol/mol creatinine respectively). The observed 1-OHP concentrations are at the lower end of those determined in children and non-occupationally exposed adults in international studies and suggest a generally low exposure to PAHs. The increased urinary 1-OHP concentrations following nights of elevated particulate concentrations in ambient air suggest increased exposure to ambient air pollution during winter time, and could potentially be used as a biomarker of exposure in this population.     

Evaluation of a year-long dispersion modelling of PM10 using the mesoscale model TAPM for Christchurch, New Zealand

This paper examines the utility of The Air Pollution Model (TAPM; version 2) in simulating meteorology and dispersion of PM(10) for 1999 over the coastal city of Christchurch, New Zealand. Christchurch usually experiences severe degradation in air quality during austral winter. The formation of a nocturnal inversion layer and the emissions of particulate matter (PM(10)) mainly from solid fuel home heating appliances lead to severe smog episodes on an average of 30 nights during winter. The complex local topography surrounding the city in combination with influences from the urban areas can produce complicated boundary layer winds during quiescent weather. Simulated PM(10) data are used for construction of annual exposure maps for the urban areas in order to assess the health impact of air pollutants due to chronic exposure (presented in an accompanying paper). Meteorology and PM(10) dispersion results are statistically compared with the only permanent air pollution monitoring station available in order to evaluate the model's performance. Statistical measures such as the Index of Agreement (IOA) between modelled and measured data indicate that the model performs well. IOA is greater than 0.6 for meteorological variables, and various calculated skill scores place confidence in the model's performance. However, TAPM has a tendency to overestimate surface wind speed over urban areas during stagnant nocturnal conditions, resulting in quick flushing of pollutants.     

Intraurban variations of PM10 air pollution in Christchurch, New Zealand: implications for epidemiological studies

Epidemiological studies relating air pollution to health effects often utilise one or few central monitoring sites for estimating wider population exposures to outdoor particulate air pollution. These studies often assume that highly correlated particulate concentrations between intraurban sites equate to a uniform concentration field. Several recent studies have questioned the universal validity of this assumption, noting that in some cities, the uniformity assumption may lead to exposure misclassification in health studies. Few studies have compared central fixed site concentrations to intraurban population background sites using actual monitored data in cities with higher levels of pollution. This research examines daily concentration variations in particulate matter less than 10 microm in diameter (PM10) at the neighbourhood scale over two winter months in Christchurch, New Zealand, a city with high winter pollution concentrations. Daily concentrations of PM10 data were collected for two winter months at ten background monitoring sites within 9.3 km of the central fixed monitoring site typically used for estimating exposure in epidemiological studies. Results indicate that while the correlation between PM10 concentrations measured at the central monitoring site and most background sites is strong (r>0.76), absolute daily concentration differences between the central monitoring site and population background sites were substantial (mean 90th percentile absolute difference=17.6 microg m-3). In Christchurch, a central monitoring site does not therefore appear to accurately depict wider area population exposures to PM10. Local intraurban variations in particulates should be well understood before applying central monitoring site concentrations as proxies for population exposure in epidemiological studies.     

A combined analysis of backward trajectories and aerosol chemistry to characterise long-range transport episodes of particulate matter: the Madrid air basin, a case study

This study has investigated the influence of synoptic weather patterns and long-range transport episodes on the concentration levels of airborne particulate matter (TSP, PM10 and PM2.5) and some major ions (SO(4)(2-), NO(3)(-) and NH(4)(+)) at a background rural station in central Spain. Air mass back-trajectories arriving at the site in 1999-2005 have been analysed by statistical methods. First, cluster analysis was used to group trajectories into 8 clusters depending on their direction and speed. Meteorological scenarios associated to each cluster have been obtained and interpreted. Then, the incidence of different air mass transport patterns on particle concentrations and composition recorded at this station was evaluated. This evaluation included PM10 and PM2.5 concentrations and chemical composition data, obtained at three representative sites of the Madrid air basin during sampling campaigns carried out in the course of the 1999-2005 period. Finally, a residence time analysis of trajectories was also performed to detect remote sources and transport pathways. Significantly elevated concentrations of TSP and PM10 were observed for Northern African flows as a consequence of the transport of mineral dust. Significant inter-cluster differences were also observed for PM2.5 and secondary inorganic compounds, with the highest concentrations associated with low baric gradient situations and Southern European flows. The residence time analysis confirmed that current TSP and PM10 concentrations in central Spain are likely to be influenced significantly by long-range transport of desert dust from different desert regions in North Africa. Furthermore, emissions from continental Europe with a high time of residence in the western and central areas of the Mediterranean basin, seem to significantly influence PM2.5 and secondary inorganic aerosol concentrations in this region.     

PM2.5 chemical composition in Hong Kong: urban and regional variations

Chemically speciated PM2.5 measurements were made at roadside, urban, and rural background sites in Hong Kong for 1 year during 2000/2001 to determine the spatial and temporal variations of PM2.5 mass and chemical composition in this highly populated region. Annual average PM2.5 concentrations at the urban and rural sites were 34.1 and 23.7 microg m(-3), respectively, approximately 50-100% higher than the United States' annual average National Ambient Air Quality Standard (NAAQS) of 15 microg m(-3). Daily PM2.5 concentrations exceeded the U.S. 24-h NAAQS of 65 microg m(-3) on 19 days, reaching 131+/-8 microg m(-3) at the roadside site on 02/28/2001. Carbonaceous aerosol is the largest contributor to PM2.5 mass (explaining 52-75% of PM2.5 mass at the two urban sites and 32% at the background site), followed by ammonium sulfate (ranging from 23% to 37% at the two urban sites and 51% at the background site). Ammonium sulfate and crustal concentrations showed more uniform spatial distributions, while the largest urban-rural contrasts found in carbonaceous aerosol (likely due to emissions from on-road gasoline and diesel vehicles). Marine influences accounted for 7% of the mass at the background site (more than twice as much as at the two urban sites). Ternary diagrams are utilized to illustrate the different spatial patterns.     

Chemical composition, mass size distribution and source analysis of long-range transported wildfire smokes in Helsinki

Special episodes of long-range transported particulate (PM) air pollution were investigated in a one-month field campaign at an urban background site in Helsinki, Finland. A total of nine size-segregated PM samplings of 3- or 4-day duration were made between August 23 and September 23, 2002. During this warm and unusually dry period there were two (labelled P2 and P5) sampling periods when the PM2.5 mass concentration increased remarkably. According to the hourly-measured PM data and backward air mass trajectories, P2 (Aug 23-26) represented a single, 64-h episode of long-range transported aerosol, whereas P5 (Sept 5-9) was a mixture of two 16- and 14-h episodes and usual seasonal air quality. The large chemical data set, based on analyses made by ion chromatography, inductively coupled plasma mass spectrometry, X-ray fluorescence analysis and smoke stain reflectometry, demonstrated that the PM2.5 mass concentrations of biomass signatures (i.e. levoglucosan, oxalate and potassium) and of some other compounds associated with biomass combustion (succinate and malonate) increased remarkably in P2. Crustal elements (Fe, Al, Ca and Si) and unidentified matter, presumably consisting to a large extent of organic material, were also increased in P2. The PM2.5 composition in P5 was different from that in P2, as the inorganic secondary aerosols (NO3-, SO4(2-), NH4+) and many metals reached their highest concentration in this period. The water-soluble fraction of potassium, lead and manganese increased in both P2 and P5. Mass size distributions (0.035-10 microm) showed that a large accumulation mode mainly caused the episodically increased PM2.5 concentrations. An interesting observation was that the episodes had no obvious impact on the Aitken mode. Finally, the strongly increased concentrations of biomass signatures in accumulation mode proved that the episode in P2 was due to long-range transported biomass combustion aerosol.     

Measuring the exposure of infants and children to indoor air pollution from biomass fuels in The Gambia

Indoor air pollution (IAP) from biomass fuels contains high concentrations of health damaging pollutants and is associated with an increased risk of childhood pneumonia. We aimed to design an exposure measurement component for a matched case-control study of IAP as a risk factor for pneumonia and severe pneumonia in infants and children in The Gambia. We conducted co-located simultaneous area measurement of carbon monoxide (CO) and particles with aerodynamic diameter <2.5 microm (PM(2.5)) in 13 households for 48 h each. CO was measured using a passive integrated monitor and PM(2.5) using a continuous monitor. In three of the 13 households, we also measured continuous PM(2.5) concentration for 2 weeks in the cooking, sleeping, and playing areas. We used gravimetric PM(2.5) samples as the reference to correct the continuous PM(2.5) for instrument measurement error. Forty-eight hour CO and PM(2.5) concentrations in the cooking area had a correlation coefficient of 0.80. Average 48-h CO and PM(2.5) concentrations in the cooking area were 3.8 +/- 3.9 ppm and 361 +/- 312 microg/m3, respectively. The average 48-h CO exposure was 1.5 +/- 1.6 ppm for children and 2.4 +/- 1.9 ppm for mothers. PM(2.5) exposure was an estimated 219 microg/m3 for children and 275 microg/m3 for their mothers. The continuous PM(2.5) concentration had peaks in all households representing the morning, midday, and evening cooking periods, with the largest peak corresponding to midday. The results are used to provide specific recommendations for measuring the exposure of infants and children in an epidemiological study. PRACTICAL IMPLICATIONS: Measuring personal particulate matter (PM) exposure of young children in epidemiological studies is hindered by the absence of small personal monitors. Simultaneous measurement of PM and carbon monoxide suggests that a combination of methods may be needed for measuring children's PM exposure in areas where household biomass combustion is the primary source of indoor air pollution. Children's PM exposure in biomass burning homes in The Gambia is substantially higher than concentrations in the world's most polluted cities.     

Performance of a high-volume cascade impactor in six European urban environments: mass measurement and chemical characterization of size-segregated particulate samples

The performance of a modified Harvard high-volume cascade impactor (HVCI) was evaluated in six field campaigns with size-segregated particulate samplings for chemical and toxicological characterization. The 7-week sampling campaigns in 2002-2003 in Duisburg (autumn), Prague (winter), Amsterdam (winter), Helsinki (spring), Barcelona (spring), and Athens (summer) were selected to represent contrasting urban environments and seasons of public health interest due to high particulate concentrations or previous findings in epidemiological studies. Particulate samples were collected in parallel with the HVCI (PM(10-2.5), PM(2.5-1), PM(1-0.2), PM(0.2)), a virtual impactor (VI; PM(10-2.5), PM(2.5)), and a Berner low-pressure impactor (BLPI; 10 stages between 0.035 and 10 mum in particle diameter) using a 3- or 4-day sampling duration. The campaigns exhibited different profiles with regard to particulate mass concentration, size distribution, chemical composition and meteorological conditions, thus providing a demanding setup for an overall field comparison of the HVCI with the VI and BLPI reference samplers. Size-segregated particulate mass concentration could be reasonably well measured with the present HVCI configuration. The coarse (PM(10-2.5)) and fine (PM(2.5)) particulate mass agreed within 10% with the low-volume reference samplers, and the four-stage size distribution of the HVCI followed the modal pattern of urban aerosol. The concentrations of chemical constituents measured and integrated especially for the HVCI-PM(2.5) differed to some extent from those measured from the corresponding VI-PM(2.5) samples. This implies that when investigating the association of toxicological responses with the chemical constituents of particulate matter, it is necessary to use the chemical composition data of the same samples as used in toxicological experiments.     

Approaching PM(2.5) and PM(2.5-10) source apportionment by mass balance analysis, principal component analysis and particle size distribution

A chemical characterization was carried out for PM(2.5) and PM(2.5-10) samples collected in a suburban area and the concentrations of 12 elements were determined in 8 size segregated fractions using a Berner Impactor. Two main objectives were proposed in this work: 1) to test for closure among chemical and gravimetric measurements of PM(2.5) and PM(2.5-10) and 2) evaluate the performance of Multilinear Regression Analysis (MLRA) and Mass Balance Analysis (MBA) in the determination of source contribution to Particulate Matter (PM) concentrations. The fraction unaccounted for by chemical analysis comprised on average 17% and 34% of gravimetric PM(2.5) and PM(2.5-10), respectively. The lack of closure in PM(2.5) and PM(2.5-10) mass (i.e., constituent concentrations not adding up to gravimetrically measured) could partly result from the presence of water associated with particles and errors in the estimation of unmeasured species. MLRA and MBA showed very similar results for the temporal variation of the source contributions. However, quantitatively important discrepancies could be observed, principally due to the lack of mass closure in PM(2.5) and PM(2.5-10). Both methods indicated that the major PM(2.5) aerosol mass contributors included secondary aerosol and vehicle exhaust. In the coarse fraction, marine and mineral aerosol contributions were predominant.     

2,3,7,8-TCDD equivalence and mutagenic activity associated with PM10 from three urban locations in New Zealand

Ambient particulate matter (PM(10)) in urban centres varies depending on emission sources, geography, demography, and meteorology. Hence physical (PM(10), wind speed, rainfall, temperature), chemical (polycyclic aromatic hydrocarbons, PAH), and toxicological (Ames Test, H4IIE EROD Assay) analyses were done on daily PM(10) (approximately 1640 m(3)/day) collected from three New Zealand urban sites where winter emissions were predominantly due to domestic home heating. Daily PM(10) levels ranged between 9.7 and 20.8 in summer and between 21.8 and 61.0 microg/m(3) in winter. Daily PAH concentrations were 0.5, 0.45, and 1.5 ng/m(3) in summer and 52.1, 128.9, and 5.8 ng/m(3) in winter at sites Christchurch, Alexandra and Dunedin, respectively. During winter, 74% of PM(10) extracts from all three sites showed significant mutagenicity in the Ames Test (TA 98, -S9), whereas approximately 25% of the daily PM(10) was mutagenic in summer. Benzo[a]pyrene and BaP carcinogenic equivalence concentrations during winter were strongly correlated to both mutagenicity and TCDD-like activity at two sites. Daily levels of TCDD toxicity equivalence concentrations ranged from 0.5 to 3.6 pg TCDD/m(3) air in summer and from 0.3 to 4009 pg TCDD/m(3) air in winter. Chemically and biologically derived TCDD toxicity equivalent concentrations were significantly correlated in all study locations indicating that PAH may represent most of the TCDD-like activity present in the PM(10).     

Intense winter atmospheric pollution episodes affecting the Western Mediterranean

The geographic location of the Western Mediterranean Basin and its peculiar topography, the climatic conditions and the intense anthropogenic and natural emissions of atmospheric pollutants are key factors necessary to interpret the atmospheric aerosol phenomenology over this area. During the cold season it is common to have severe atmospheric particulate matter (PM) pollution episodes (of an anthropogenic origin) affecting this region, not only in the urban and industrial areas but also in the regional and rural sites. During these episodes, the midday hourly PM₁ levels at regional background sites are in many cases higher than those at urban areas. Around 10% of the days under winter anticyclonic conditions registered similar PM₁ levels at the regional background than at the urban area and, sporadically the daily PM₁ levels at the regional background sites may exceed those at urban sites. Furthermore, the very high hourly PM₁ levels measured at regional background sites during these episodes are not regularly attained in the closest urban areas, which leads to the hypothesis that an important formation of secondary aerosols occurs during the transport of the polluted air masses towards the elevated rural sites.The interpretation of the variability of PM levels and composition (2002-2008) at one urban site (Barcelona) and at one regional background site (Montseny) allows us to illustrate the phenomenology of these scenarios, to quantify the mean annual contributions to the PM levels and to identify their main tracers. Ammonium nitrate appears to be the most abundant compound during these scenarios, although organic species and trace metals also increase markedly. Owing to the intensity, composition and recurrence of these atmospheric pollution episodes, important health, climatic and ecological implications may be derived.     

Factors influencing mass concentration and chemical composition of fine aerosols during a PM high pollution episode

Results obtained during a winter field campaign for the fine fractions of particulate matter are presented. A high pollution episode together with an analysis of the main factors, which influence accumulation of pollutants is described. The measurement campaigns were carried out simultaneously at two sites in Northern Italy, Milan and Erba, during the winter of 2000. The daily variability in the mass concentration values and PM2.5/PM10 ratios appeared to be strongly dependent upon meteorological and atmospheric stability conditions and, in particular, wind regimes. During the intensive field campaign a high-pollution episode occurred that led to TSP and fine fraction concentrations well above the attention and alarm thresholds, reaching values of up to 200-250 microg m(-3). The elemental concentrations were determined by ED-XRF analysis. The elemental composition of the particulate matter indicated that crustal matter oxides (soil dust) were the main component in particles with aerodynamic diameter d(ae) > 10 microm. They were an important part also in particles with 2.5 < d(ae) < 10 microm, but strongly decreased in particles with d(ae) < 2.5 microm. In the finer fraction sulphates nitrogen and carbon compounds played a major role. The temporal patterns of mass and elemental concentrations, as well as the main components of PM were very similar at the two sites. The high-pollution episode was recorded at many locations in the Po plain, highlighting the role of meteorology and thermodynamic atmospheric conditions on pollution build-up on a large area.     

Comparative PM10-PM2.5 source contribution study at rural, urban and industrial sites during PM episodes in Eastern Spain

In this study a set of 340 PM10 and PM2.5 samples collected throughout 16 months at rural, an urban kerbside and an industrial background site (affected by the emissions from the ceramic manufacture and other activities) were interpreted. On the regional scale, the main PM10 sources were mineral dust (mainly Al2O3, Fe, Ti, Sr, CaCO3, Mg, Mn and K), emissions derived from power generation (SO4=, V, Zn and Ni), vehicle exhausts (organic and elemental carbon, NO3- and trace elements) and marine aerosol (Na, Cl and Mg). The latter was not identified in PM2.5. At the industrial site, additional PM10 sources were identified (tile covering in the ceramic production, petrochemical emissions and bio-mass burning from a large orange tree cultivation area). The contribution of each PM source to PM10 and PM2.5 levels experiences significant variations depending on the type of PM episode (Local-urban mainly in autumn-winter, regional mainly in summer, African or Atlantic episode), which are discussed in this study. The results show that it would be very difficult to meet the EU limit values for PM10 established for 2010. The annual mean PM levels are 22.0 microg PM10/m3 at the rural and 49.5 microg PM10/m3 and 33.9 microg PM2.5/m3 at the urban site. The natural contribution in this region, estimated at 6 microg/m3 of natural mineral dust (resulting from the African events and natural resuspension) and 2 microg/m3 of marine aerosol, accounts for 40% of the 2010 EU annual limit value (20 microg PM10/m3). Mineral dust concentrations at the urban and industrial sites are higher than those at the rural site because of the urban road dust and the ceramic-production contributions, respectively. At the urban site, the vehicle exhaust contribution (17 microg/m3) alone is very close to the 2010 EU PM10 limit value. At the rural site, the African dust is the main contributor to PM10 levels during the highest daily mean PM10 events (100th-97th percentile range). At the urban site, the vehicle exhaust product is the main contributor to PM10 and PM2.5 levels during the highest daily mean PM events (100th-85th percentile range). Mineral dust concentrations during African dust events accounts for 20-30 microg/m3 in PM10 and 10-15 microg/m3 in PM2.5. During non-African dust events, mineral dust derived from anthropogenic activities (e.g. urban road dust) is also a significant contributor to PM10, but not to PM2.5.     

Characterization of atmospheric mineral components of PM2.5 in Beijing and Shanghai, China

Weekly PM2.5 samples were collected for one year in Beijing and Shanghai and the crustal elements analyzed to investigate the concentration levels and temporal variations of ambient fine mineral dust. The mass concentrations of Al, Si, Ca, Mg, and Fe exhibited similar significant weekly variations in both Beijing and Shanghai. The annual average PM2.5 concentrations of major crustal elements ranged from 0.27 microg m-3 Mg to 2.48 microg m-3 Si in Beijing, which were 1.40-2.24 times higher than those in Shanghai. Their PM-weighted values were comparable between the two cities. A distinct seasonal pattern was present for these crustal elements with the highest concentrations during the spring in Beijing and during the winter in Shanghai, and the lowest concentrations during the summer in both cities. During the dusty spring of 2000 in Beijing, soil dust was the second most abundant PM2.5 constituent with a contribution as high as 18.6%, over twice that in the winter. The highest fine soil concentration (37.8 microg m-3) and mass percentage (41.6%) occurred in the same week of intensive dust events impacting Beijing. The impact of dust storms complicates the goal of reducing PM2.5 in Beijing. Ca originating from construction activities appears to be a significant PM2.5 contributor as well.     

Aerosol optical depth, aerosol composition and air pollution during summer and winter conditions in Budapest

The dependence of aerosol optical depth (AOD) on air particulate concentrations in the mixing layer height (MLH) was studied in Budapest in July 2003 and January 2004. During the campaigns gaseous (CO, SO(2), NO(x), O(3)), solid components (PM(2.5), PM(10)), as well as ionic species (ammonium, sulfate and nitrate) were measured at several urban and suburban sites. Additional data were collected from the Budapest air quality monitoring network. AOD was measured by a ground-based sun photometer. The mixing layer height and other common meteorological parameters were recorded. A linear relationship was found between the AOD and the columnar aerosol burden; the best linear fit (R(2)=0.96) was obtained for the secondary sulfate aerosol due to its mostly homogeneous spatial distribution and its optically active size range. The linear relationship is less pronounced for the PM(2.5) and PM(10) fractions since local emissions are very heterogeneous in time and space. The results indicate the importance of the mixing layer height in determining pollutant concentrations. During the winter campaign, when the boundary layer decreases to levels in between the altitudes of the sampling stations, measured concentrations showed significant differences due to different local sources and long-range transport. In the MLH time series unexpected nocturnal peaks were observed. The nocturnal increase of the MLH coincided with decreasing concentrations of all pollutants except for ozone; the ozone concentration increase indicates nocturnal vertical mixing between different air layers.     

Particle size distribution and composition in a mechanically ventilated school building during air pollution episodes

Particle count-based size distribution and PM(2.5) mass were monitored inside and outside an elementary school in Salt Lake City (UT, USA) during the winter atmospheric inversion season. The site is influenced by urban traffic and the airshed is subject to periods of high PM(2.5) concentration that is mainly submicron ammonium and nitrate. The school building has mechanical ventilation with filtration and variable-volume makeup air. Comparison of the indoor and outdoor particle size distribution on the five cleanest and five most polluted school days during the study showed that the ambient submicron particulate matter (PM) penetrated the building, but indoor concentrations were about one-eighth of outdoor levels. The indoor:outdoor PM(2.5) mass ratio averaged 0.12 and particle number ratio for sizes smaller than 1 microm averaged 0.13. The indoor submicron particle count and indoor PM(2.5) mass increased slightly during pollution episodes but remained well below outdoor levels. When the building was occupied the indoor coarse particle count was much higher than ambient levels. These results contribute to understanding the relationship between ambient monitoring station data and the actual human exposure inside institutional buildings. The study confirms that staying inside a mechanically ventilated building reduces exposure to outdoor submicron particles. PRACTICAL IMPLICATIONS: This study supports the premise that remaining inside buildings during particulate matter (PM) pollution episodes reduces exposure to submicron PM. New data on a mechanically ventilated institutional building supplements similar studies made in residences.     

Particulate matter and carbon monoxide multiple regression models using environmental characteristics in a high diesel-use area of Baguio City, Philippines

In Baguio City, Philippines, a mountainous city of 252,386 people where 61% of motor vehicles use diesel fuel, ambient particulate matter <2.5 microm (PM(2.5)) and <10 microm (PM(10)) in aerodynamic diameter and carbon monoxide (CO) were measured at 30 street-level locations for 15 min apiece during the early morning (4:50-6:30 am), morning rush hour (6:30-9:10 am) and afternoon rush hour (3:40-5:40 pm) in December 2004. Environmental observations (e.g. traffic-related variables, building/roadway designs, wind speed and direction, etc.) at each location were noted during each monitoring event. Multiple regression models were formulated to determine which pollution sources and environmental factors significantly affect ground-level PM(2.5), PM(10) and CO concentrations. The models showed statistically significant relationships between traffic and early morning particulate air pollution [(PM(2.5)p=0.021) and PM(10) (p=0.048)], traffic and morning rush hour CO (p=0.048), traffic and afternoon rush hour CO (p=0.034) and wind and early morning CO (p=0.044). The mean early morning, street-level PM(2.5) (110+/-8 microg/m3; mean+/-1 standard error) was not significantly different (p-value>0.05) from either rush hour PM(2.5) concentration (morning=98+/-7 microg/m3; afternoon=107+/-5 microg/m3) due to nocturnal inversions in spite of a 100% increase in automotive density during rush hours. Early morning street-level CO (3.0+/-1.7 ppm) differed from morning rush hour (4.1+/-2.3 ppm) (p=0.039) and afternoon rush hour (4.5+/-2.2 ppm) (p=0.007). Additionally, PM(2.5), PM(10), CO, nitrogen dioxide (NO2) and select volatile organic compounds were continuously measured at a downtown, third-story monitoring station along a busy roadway for 11 days. Twenty-four-hour average ambient concentrations were: PM(2.5)=72.9+/-21 microg/m3; CO=2.61+/-0.6 ppm; NO2=27.7+/-1.6 ppb; benzene=8.4+/-1.4 microg/m3; ethylbenzene=4.6+/-2.0 microg/m3; p-xylene=4.4+/-1.9 microg/m3; m-xylene=10.2+/-4.4 microg/m3; o-xylene=7.5+/-3.2 microg/m3. The multiple regression models suggest that traffic and wind in Baguio City, Philippines significantly affect street-level pollution concentrations. Ambient PM(2.5) levels measured are above USEPA daily (65 microg/m3) and Filipino/USEPA annual standards (15 microg/m3) with concentrations of a magnitude rarely seen in most countries except in areas where local topography plays a significant role in air pollution entrapment. The elevated pollution concentrations present and the diesel-rich nature of motor vehicle emissions are important pertaining to human exposure and health information and as such warrant public health concern.     

Source apportionment of PM10 and PM2.5 in Milan (Italy) using receptor modelling

In this paper a source apportionment of particulate matter pollution in the urban area of Milan (Italy) is given. Results of PM10 and PM2.5 mass and elemental concentrations from a 1-year monitoring campaign are presented. Mean annual and daily PM10 levels are compared with the limits of the EU Air Quality Directive EC/30/1999 and the results show that the limit values established would not be met in the urban area of Milan or the large surrounding area. Moreover, high levels of PM2.5 are registered and this fraction constitutes a high portion of the PM10 mass. In Milan the winter period is characterised by a high degree of air pollution due to a greater contribution of emissions and to adverse meteorological and thermodynamic conditions of the atmosphere. The application of multivariate techniques and receptor modelling (PCFA, APCFA) to the whole data-set led to the identification of the main emitting sources and to the source apportionment of PM10 and PM2.5 in Milan. The most important sources were identified as 'soil dust', 'traffic', 'industry' and 'secondary compounds' for PM10 and as 'soil dust', 'anthropogenic' and 'secondary compounds' for PM2.5, explaining the greatest part of the total variance (91% and 75%, respectively).     

Seasonal variations and mass closure analysis of particulate matter in Hong Kong

The chemical characteristics of ambient particulate matters in urban and rural areas of Hong Kong were determined in this study. A monitoring program starting from November 2000 to February 2001 (winter) and June 2001 to August 2001 (summer) for PM10 and PM2.5 was performed at three monitoring stations in Hong Kong. Twenty-four-hour PM10 and PM2.5 samples were collected once every 6 days at two urban sites, PolyU and KT, and every 12 days at a background site, HT, with Hi-Vol samplers. High concentrations of OC, EC (except in PolyU), water-soluble ions and elements were observed in winter among the three sampling sites for PM10 and PM2.5 fractions. Seasonal variations were significant in background HT. Dilution effect due to the increase in mixing depth and precipitation in summer reduced the concentrations of particulate matters. Long-range transport could contribute to the higher concentrations of particulate matter in the winter. Chemical mass closure calculations were performed for PM10 and PM2.5 observed. Mass closure improved when separate factors (1.4 and 1.9 respectively) were used to convert water-soluble organic carbon (WSOC) and water-insoluble organic carbon (WINSOC) into corresponding organic masses. The urban sites showed high percentages of water-soluble ions in winter and high percentages of carbonaceous species in summer. Better results were obtained for the chemical mass closure analysis in winter than in summer. High temperature and solar radiation in summer increased the rate of the complex photochemical reaction in the atmosphere. Therefore the chemical mass closure analysis would underestimate the volatized species and secondary aerosols during summer.