超高强QP980钢冲压成形性能

目的研究宝钢新一代先进高强钢QP980与第一代先进高强钢DP980的冲压成形性能。方法采用单向拉伸、光学应变分析和帽型拉弯成形等试验方法,分析两种超高强钢在加工硬化、成形极限、拉弯成形侧壁减薄和回弹等性能特性。结果 QP980的伸长率达到21.6%,与DP980钢相比有更高的强塑积,在变形过程中能够维持较高的瞬时n值,进而提高了材料的成形极限。帽型拉弯试验中,在不同的流入距离条件下,QP980钢的侧壁减薄率均低于DP980钢。在不同压边力条件下,QP980(厚度1.0 mm)材料的回弹量大于DP980(厚度1.2 mm)材料。结论 QP980在梁型件成形过程中具有优良的抗减薄特性,采用QP980钢进行冲压成形时应考虑比同级别DP980钢更大的回弹补偿量,或者采用更大变形量的工艺设计。     

基于零件应用的第3代高强钢——QP钢的成形特性

目的研究第3代高强钢——QP钢在实际零件上应用涉及的成形特性问题。方法通过微观组织分析、单向拉伸、成形极限、V形弯曲回弹等试验,分析探讨了QP钢的力学性能、成形性能、成形极限和弯曲特性,并与广泛应用的DP钢对比。结果 QP钢HC600/980QP的成形性能好于相同强度级别的DP钢HC550/980DP,与HC420/780DP相当;QP钢弯曲回弹量比同等强度级别DP钢大。通过2个试冲零件的分析,验证了QP的成形特性,并从零件应用角度提出了QP钢的零件适用范围和零件设计要点。结论 QP钢具有综合的强度和塑性性能,有助于解决局部特征复杂的难成形零件和具有等截面特征的零件,在汽车车身结构件上有较大的应用前景。     

高强钢帽形梁零件冲压减薄预测分析

目的 针对高强钢帽形梁强度高、塑性差、结构复杂、冲压过程中出现减薄破裂等情况,建立QP980高强度钢冲压成形减薄预测模型,解决实际生产工程难题。方法 以典型高强钢车身零件帽形梁为对象,利用人工神经网络模型研究工件结构和减薄率之间的关系,将贝叶斯优化算法和循环人工神经网络相结合,建立冲压成形减薄的高精度预测模型,对高强钢帽形梁零件冲压成形时减薄量进行优化设计,通过AutoForm软件验证算法模型的准确性。结果 拉深高度对减薄率影响最大,对外减薄率影响达到41.7%,对内减薄影响达到46.2%,人工神经网络模型对测试集5组数据的预测平均误差均小于0.3%。根据人工神经网络求解QP980钢在极限减薄率25%下的最大拉深高度为55.417 mm,人工神经网络预测结果与Autoform仿真结果相差0.3%,验证了人工神经网络模型的准确性。结论 采用该模型解决了CAE模拟在较少试验数据条件下算法预测精度差的问题,能有效缩短高强钢零件冲压成形调试周期,提高生产效率。     

超高强度钢DP1000液压成形A柱的关键技术

目的研究超高强度钢DP1000液压成形A柱仿真技术和试验效果,解决批量生产中DP100焊管技术和同步冲孔等关键技术。方法基于Autoform有限元模拟软件,仿真分析了DP1000液压成形A柱的可行性,试验了DP1000液压成形A柱零件。通过对比高频焊管和激光焊管的液压成形零件焊缝质量,解决量产零件开裂问题,开展了DP1000液压成形A柱的Cr12MoV、ASP30和SKH51不同材料的同步冲孔效果,解决DP1000材料冲头寿命和冲孔质量问题。结果采用DP1000材料可以获得液压成形A柱,具有制造可行性。与高频焊管相比,具有较小的热影响区和硬度变化较小的激光焊管,更适合DP1000液压成形A柱使用。结论 ASP30和SKH51比传统的Cr12MoV更适合于DP1000材料液压成形A柱同步冲孔,冲头寿命提高80多倍,冲孔质量良好。     

980 MPa先进高强钢材料在门槛加强梁上的辊压应用

目的为获得980 MPa级别不同先进高强钢材料在辊压零件上应用时的差异,研究典型980 MPa先进高强钢的辊压成形特性。方法采用调研和统计方法获得门槛辊压用材的主流强度与钢种,基于三点弯曲的实验方法,获得了980 MPa先进高强钢材料在指定角度和弯曲半径下的回弹特性,针对典型的门槛加强梁零件,采用CAE方法评估材料应用的可行性。结果门槛零件980 MPa级别所采用的主要先进刚强钢钢种为双相钢(DP)和马氏体钢(MS),在相对弯曲半径比R/t=2.5的情况下,980DP回弹角度最小,980QP次之,980MS最大;早期模具回弹补偿设计时对于90°圆角可给予11°~14°的回弹过弯角度;成形过程中有可能出现边波缺陷,需优化辊压成形变形过程。结论 980 MPa先进高强钢材料在应用于辊压零件时,应在设计阶段充分考虑材料回弹特性,同时变形过程应合理,避免产生边波等质量缺陷。     

小曲率铝合金框形件弯胀成形数值模拟研究

目的 针对一种小曲率铝合金框形件成形后回弹大和起皱问题,对其进行弯胀复合成形工艺的数值模拟研究。方法 基于DYNAFORM软件对成形过程进行仿真,并通过对比分析零件的最大减薄率及圆角处的贴膜度,得出该零件最大液室压力的最优值为20 MPa,并基于该参数进行壁厚分布及回弹的模拟分析,最后,通过现场试验对该成形方案进行验证。结果 通过采用弯胀复合成形工艺方法,该零件的最大回弹量控制在2 mm以内,零件整体成形质量较好,无破裂、起皱现象。结论 该种成形方法较刚性模压弯及主动式充液胀形更具优势,能够有效解决小曲率框形件回弹大及起皱问题。     

变厚度轮辐强力旋压成形过程的分析

利用ABAQUS/Explicit模拟了变厚度轮辐双道次强力旋压过程,给出了建模和分析结果.轮辐旋压成形伴随板坯的剧烈减薄,收口区域较难成形,减薄率达50%,在计算中,轮辐有限元网格畸变严重,为此运用ALE技术改善网格质量,提高了计算精度.对模拟的旋压轮辐厚度与实验测量值进行了对比,二者吻合较好,验证了计算模型和结果的可靠性.通过ABAQUS/Standard计算了轮辐旋压成形后的回弹变形量和残余应力,分析成形后轮辐等效应变分布及回弹特征,研究发现,回弹变形量与旋压成形时壁厚变化量成正比.     

面向壁厚均匀的液压成形三通管的坯料设计方法与参数优化

目的 研究连续变厚度管液压成形过程中三通管的壁厚均匀性问题。方法 首先,利用有限元软件分析得到了等厚管液压成形三通管过程中的成形规律,根据其成形规律,反向设计了用于液压成形三通管的连续变厚度管坯;其次,采用正交试验方法,研究了连续变厚度管厚区壁厚、过渡区长度对液压成形三通管成形质量的影响;最后,采用多岛遗传算法,对连续变厚度管的结构参数进行了优化验证,提高了液压成形三通管的成形质量。结果 在等厚管液压成形三通管成形过程中,支管顶部壁厚值持续减小、轴向过渡圆角及直管底部中间位置处壁厚值持续增大;环向过渡圆角处等效应力最大,其他位置连续变化;轴向压应力使得三通管壁厚增大,拉应力使得壁厚减小;正交试验结果表明,当连续变厚度管厚区厚度、环向过渡区长度达到某一值时将出现较好的壁厚均匀性;在4种过渡区曲线线型中,直线型的壁厚均匀性最好;通过多目标优化得到最佳连续变厚度管结构参数,并通过有限元仿真进行验证,相对误差均在2 %以内,使用优化后的连续变厚度管液压成形三通管相对于等厚管,壁厚均匀值减小了0.423 mm。结论 可以采用厚度补偿或减薄的方式来提高成形三通管的壁厚均匀性;连续变厚度管坯相比于等厚管,显著提高了液压成形三通管的壁厚均匀性。     

基于Autoform和Dynaform软件的超高强钢零件仿真对比

目的研究商用软件Autoform和Dynaform对超高强钢零件的回弹预测精度。方法以某车型前围板中间横梁零件冲压成形过程为例,分别基于Autoform和Dynaform软件建立冲压有限元模型模拟冲压成形和回弹过程,对两种软件成形性和回弹计算结果进行比较和讨论分析。结果 Dynaform和Autoform两种软件在成形性计算时结果比较一致,相同位置Autoform计算减薄率为16%,Dynaform为16.2%;Dynaform计算的最大减薄率为18%,比Autoform的16.2%略大;两种软件基本在相同位置预测出了起皱和开裂现象;比较修边后回弹仿真值与实测值,Dynaform计算的偏差满足设定阈值的占51.4%,高出Autoform约20%。结论 Dynaform计算的最大减薄率更大一些,对应量产时较高的安全裕度;同时其回弹计算结果与实测回弹值更为接近,回弹预测精度更高。     

预拉深对气胀钛合金筒形件壁厚均匀性的影响

以钛合金筒形件为研究对象,针对传统气胀成形存在减薄率过大问题,开展了预拉深-气胀复合成形方法研究。采用数值模拟分析了传统气胀成形中筒底减薄率过大的原因,实验研究了不同加载路径对TA15筒形件减薄率的影响。结果表明:气胀成形的加载速度对减薄率有一定的影响,慢速气胀和快速气胀成形件最大减薄率分别为63.2%、54.2%,仅提高加载速度并不能满足壁厚均匀性要求;在有一定预拉深的情况下,通过热拉深-气胀复合成形,最大减薄率可减小到36.7%。热拉深-气胀复合成形工艺可有效改善成形件的壁厚分布均匀性.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Institutions Expected to Update and Transfer Information on Present Standards

Standards are the basis for production enterprises to organize production, ex-factory inspection, trade (delivery) and technical exchanges, product certification, quality arbitration and supervision.……     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Optimum-Simulation von Ernteprozessen

Zusammenfassung Bei der Gestaltung von Ernteprozessen — beispielsweise des Prozesses Mähdrusch, Körnertransport und -abnahme — als transportverbundene Fließarbeitsverfahren mit mindestens zwei verschiedenen Arbeitsmitteln gibt es einen großen Optimierungsspielraum. Solche Prozesse sind mehrstufige Bedienungsprozesse mit gemischter Anordnung der Bedienungseinrichtungen. Außerdem besitzen sie stark ausgeprägte räumliche Aspekte. Es wird vor allem gezeigt, welche Merkmale solcher Prozesse in Simulationsmodellen abgebildet sein müssen, welche Zielgrößen in Abhängigkeit von welchen Einflußgrößen unter Berücksichtigung welcher Prozeßbedingungen ermittelt werden sollten und wie der Bewertungsprozeß zur Ermittlung der gewünschten Informationen gestaltet werden muß.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.