Characterization of indium zinc oxide thin films prepared by pulsed laser deposition using a Zn3In2O6 target

Using a Zn₃In₂O₆ target, indium-zinc oxide films were prepared by pulsed laser deposition. The influence of the substrate deposition temperature and the oxygen pressure on the structure, optical and electrical properties were studied. Crystalline films are obtained for substrate temperatures above 200°C. At the optimum substrate deposition temperature of 500°C and the optimum oxygen pressure of 10⁻³ mbar, both conditions that indeed lead to the highest conductivity, Zn₃In₂O₆ films exhibit a transparency of 85% in the visible region and a conductivity of 1000 S/cm. Depositions carried out in oxygen and reducing gas, 93% Ar/7% H₂, result in large discrepancies between the target stoichiometry and the film composition. The Zn/In (at.%) ratio of 1.5 is only preserved for oxygen pressures of 10⁻²–10⁻³ mbar and a 93% Ar/7% H₂ pressure of 10⁻² mbar. The optical properties are basically not affected by the type of atmosphere used during the film deposition, unlike the conductivity which significantly increases from 80 to 1400 S/cm for a film deposited in 10⁻² mbar of O₂ and in 93% Ar/7% H₂, respectively.     

Sintering behavior and microwave dielectric properties of Bi3(Nb1−xTax)O7 solid solutions

Solid solutions of Bi₃(Nb_1−xTa_x)O₇ (x = 0.0, 0.3, 0.7, 1) were synthesized using solid state reaction method and their microwave dielectric properties were first reported. Pure phase of fluorite-type could be obtained after calcined at 700 °C (2 h)⁻¹ between 0 ≤ x ≤ 1 and Bi₃(Nb_1−xTa_x)O₇ ceramics could be well densified below 990 °C. As x increased from 0.0 to 1.0, saturated density of Bi₃(Nb_1−xTa_x)O₇ ceramics increased from 8.2 to 9.1 g cm⁻³, microwave permittivity decreased from 95 to 65 while Q_f values increasing from 230 to 560 GHz. Substitution of Ta for Nb modified temperature coefficient of resonant frequency τ_f from −113 ppm °C⁻¹ of Bi₃NbO₇ to −70 ppm °C⁻¹ of Bi₃TaO₇. Microwave permittivity, Q_f values and τ_f values were found to correlate strongly with the structure parameters of fluorite solid solutions and the correlation between them was discussed in detail. Considering the low densified temperature and good microwave dielectric proprieties, solid solutions of Bi₃(Nb_1−xTa_x)O₇ ceramics could be a good candidate for low temperature co-fired ceramics application.     

Al2O3 formation on Si by catalytic chemical vapor deposition

Catalytic chemical vapor deposition (Cat-CVD) has been developed to deposit alumina (Al₂O₃) thin films on silicon (Si) crystals using N₂ bubbled tri-methyl aluminum [Al(CH₃)₃, TMA] and molecular oxygen (O₂) as source species and tungsten wires as a catalyzer. The catalyzer dissociated TMA at approximately 600 °C. The maximum deposition rate was 18 nm min⁻¹ at a catalyzer temperature of 1000 °C and substrate temperature of 800 °C. Metal oxide semiconductor (MOS) diodes were fabricated using gates composed of 32.5-nm-thick alumina film deposited at a substrate temperature of 400 °C. The capacitance measurements resulted in a relative dielectric constant of 7.4, fixed charge density of 1.74×10¹² cm⁻², small hysteresis voltage of 0.12 V, and very few interface trapping charges. The leakage current was 5.01×10⁻⁷ A cm⁻² at a gate bias of 1 V.     

Investigation of stress behaviors and mechanism of void formation in sputtered TiSix films

We have investigated the stress behaviors and a mechanism of void formation in TiSi_x films during annealing. TiSi_x thin films were prepared by DC magnetron sputtering using a TiSi_2.1 target in the substrate temperature range of 200–500 °C. The as-deposited TiSi_x films at low substrate temperature (<300 °C) have an amorphous structure with low stress of 1×10⁸ dynes/cm². When the substrate temperature increases to 500 °C, the as-deposited TiSi_x film has a mixture of C49 and C54 TiSi₂ phase with stress of 8×10⁹ dynes/cm². No void was observed in the as-deposited TiSi_x film. Amorphous TiSi_x film transforms to C54 TiSi₂ phase with a random orientation of (311) and (040) after annealing at 750 °C. The C49 and C54 TiSi₂ mixture phase transforms to (040) preferred C54 TiSi₂ phase after annealing over 650 °C. By increasing substrate temperature, the transformation temperature for C54 TiSi₂ can be reduced, resulting in relieved stress of TiSi₂ film. The easy nucleation of the C54 phase was attributed to an avoidance of amorphous TiSi_x phase. We found that amorphous TiSi_x→C54 TiSi₂ transformation caused higher tensile stress of 2×10¹⁰ dynes/cm², resulting in more voids in the films, than C49→C54 transformation. It was observed that void formation was increased with thermal treatment. The high tensile stress caused by volume decreases in the silicide must be relieved to retard voids and cracks during C54 TiSi₂ formation.     

Structure and conducting properties of La0.5Sr0.5CoO3−δ films on YSZ

La_0.5Sr_0.5CoO_3−δ (LSCO) thin films were deposited on yttria stabilized zirconia (YSZ) substrates by pulsed laser deposition (PLD) for application to thin film solid oxide fuel cell electrodes. During the deposition, the substrate temperature was varied from 450 to 750°C, and the oxygen pressure in the chamber was varied from 80 to 310 mTorr. Films deposited at 650°C and an oxygen background pressure of 150 mTorr were mostly (100) oriented. Deposition at higher temperatures or under lower oxygen pressures lead to mostly (110) oriented films. Films with low electrical resistivity of 10⁻³ Ω·cm were obtained.     

Investigation on the cross sensitivity of NO2 sensors based on In2O3 thin films prepared by sol-gel and vacuum thermal evaporation

In₂O₃ thin films have been prepared from commercially available pure In₂O₃ powders by high vacuum thermal evaporation (HVTE) and from indium iso-propoxide solutions by sol-gel techniques (SG). The films have been deposited on sapphire substrates provided with platinum interdigital sputtered electrodes. The as-deposited HVTE and SG films have been annealed at 500°C for 24 and 1 h, respectively. The film morphology, crystalline phase and chemical composition have been characterised by SEM, glancing angle XRD and XPS techniques. After annealing at 500°C the films’ microstructure turns from amorphous to crystalline with the development of highly crystalline cubic In₂O_3−x (JCPDS card 6-0416). XPS characterisation has revealed the formation of stoichiometric In₂O₃ (HVTE) and nearly stoichiometric In₂O_3−x (SG) after annealing. SEM characterisation has highlighted substantial morphological differences between the SG (highly porous microstructure) and HVTE (denser) films. All the films show the highest sensitivity to NO₂ gas (0.7–7 ppm concentration range), at 250°C working temperature. At this temperature and 0.7 ppm NO₂ the calculated sensitivities (S=R_g/R_a) yield S=10 and S=7 for SG and HVTE, respectively. No cross sensitivity have been found by exposing the In₂O₃ films to CO and CH₄. Negligible H₂O cross has resulted in the 40–80% relative humidity range, as well as to 1 ppm Cl₂ and 10 ppm NO. Only 1000 ppm C₂H₅OH has resulted to have a significant cross to the NO₂ response.     

Properties of tantalum oxide thin films grown by atomic layer deposition

Thin tantalum oxide films were deposited using atomic layer deposition from TaCl₅ and H₂O at temperatures in the range 80–500 °C. The films deposited at temperatures below 300 °C were predominantly amorphous, whereas those grown at higher temperatures were polycrystalline containing the phases TaO₂ and Ta₂O₅. The oxygen to tantalum mass concentration ratio corresponded to that of TaO₂ at all growth temperatures. The optical band gap was close to 4.2 eV for amorphous films and ranged from 3.9 to 4.5 eV for polycrystalline films. The refractive index measured at λ = 550 nm increased from 1.97 to 2.20 with an increase in growth temperature from 80 to 300 °C. The films deposited at 80 °C showed low absorption with absorption coefficients of less than 100 cm⁻¹ in the visible region.     

Fabrication of robust Bi3.25La0.75Ti3O12 thin film resistant to hydrogen damage

Ferroelectric bismuth lanthanum titanate (Bi_3.25La_0.75Ti₃O₁₂; BLT) thin films were deposited on Pt/TiO₂/SiO₂/Si substrate by chemical solution deposition method. The films were crystallized in the temperature range of 600–700 °C. The spontaneous polarization (P_s) and the switching polarization (2P_r) of BLT film annealed at 700 °C for 30 min were 22.6 μC/cm² and 29.1 μC/cm², respectively. Moreover, the BLT capacitor did not show any significant reduction of hysteresis for 90 min at 300 °C in the forming gas atmosphere.     

Highly conducting indium tin oxide (ITO) thin films deposited by pulsed laser ablation

Highly conducting and transparent indium tin oxide (ITO) thin films were prepared on SiO₂ glass and silicon substrates by pulsed laser ablation (PLA) from a 90 wt.% In₂O₃-10 wt.% SnO₂ sintered ceramic target. The growths of ITO films under different oxygen pressures (P_O2) ranging from 1×10⁻⁴–5×10⁻² Torr at low substrate temperatures (T_s) between room temperature (RT) and 200°C were investigated. The opto-electrical properties of the films were found to be strongly dependent on the P_O2 during the film deposition. Under a P_O2 of 1×10⁻² Torr, ITO films with low resistivity of 5.35×10⁻⁴ and 1.75×10⁻⁴ Ω cm were obtained at RT (25°C) and 200°C, respectively. The films exhibited high carrier density and reasonably high Hall mobility at the optimal P_O2 region of 1×10⁻² to 1.5×10⁻² Torr. Optical transmittance in excess of 87% in the visible region of the solar spectrum was displayed by the films deposited at Po₂≥1×10⁻² Torr and it was significantly reduced as the P_O2 decreases.     

Structure and electrical properties of (100)-oriented Pb(Zn1/3Nb2/3)O3–Pb(Mg1/3Nb2/3)O3–PbTiO3 thin films on La0.7Sr0.3MnO3 electrode by chemical solution deposition

(100)-oriented 0.462Pb(Zn_1/3Nb_2/3)O₃–0.308Pb(Mg_1/3Nb_2/3)O₃–0.23PbTiO₃ (PZN-PMN-PT) perovskite ferroelectric thin films were prepared on La_0.7Sr_0.3MnO₃/LaAlO₃ (LSMO/LAO) substrate via a chemical solution deposition route. The perovskite LSMO electrode was found to effectively suppress the pyrochlore phase while promote the growth of the perovskite phase in the PZN-PMN-PT film. The film annealed at 700 °C exhibited a high dielectric constant of 2130 at 1 kHz, a remnant polarization, 2P_r, of 29.8 μC/cm², and a low leakage current density of 7.2 × 10^− 7 A/cm² at an applied field of 200 kV/cm. The ferroelectric polarization was fatigue-free at least up to 10¹⁰ cycles. Piezoelectric coefficient, d₃₃, of 48 pm/V was also demonstrated. The results showed that much superior properties could be achieved with the PZN-PMN-PT thin films on the solution derived LSMO electrode than on Pt electrode by sputtering.     

Effect of deposition temperature on the structural and thermoelectric properties of bismuth telluride thin films grown by co-sputtering

Thermoelectric bismuth telluride thin films were prepared on SiO₂/Si substrates by radio-frequency (RF) magnetron sputtering. Co-sputtering method with Bi and Te targets was adopted to control films' composition. Bi_xTe_y thin films were elaborated at various deposition temperatures with fixed RF powers, which yielded the stoichiometric Bi₂Te₃ film deposition without intentional substrate heating. The effects of deposition temperature on surface morphology, crystallinity and electrical transport properties were investigated. Hexagonal crystallites were clearly visible at the surface of films deposited above 290 °C. Change of dominant phase from rhombohedral Bi₂Te₃ to hexagonal BiTe was confirmed with X-ray diffraction analyses. Seebeck coefficients of all samples have negative value, indicating the prepared Bi_xTe_y films are n-type conduction. Optimum of Seebeck coefficient and power factor were obtained at the deposition temperature of 225 °C (about − 55 μV/K and 3 × 10^− 4 W/K²·m, respectively). Deterioration of thermoelectric properties at higher temperature could be explained with Te deficiency and resultant BiTe phase evolution due to the evaporation of Te elements from the film surface.     

Stresses in sputtered RUOx thin films

RuO_x thin films have been deposited by reactive sputtering in an O₂/Ar atmosphere. The films were characterized for their stress and resistivity as a function of deposition temperature (room temperature, 300°C) and the O₂ content (25–100%) in the sputtering gas. Additionally, the stresses in these films were determined as a function of annealing temperature (up to 600°C) using an in-situ curvature measurement technique. The as-deposited films were found to be under a state of compressive stress for all deposition conditions. The compressive stresses sharply increased with increasing deposition temperature from a value of around 200 MPa at 200°C to 1400 MPa at 300°C. This dramatic increase has been attributed to differences in microstructure at these deposition temperatures. The microstructural differences also led to the widely differing stress-temperature behavior during annealing of these films. For films deposited at temperatures lower than 200°C, the annealing process resulted in a decrease in the compressive stress and resistivity of the films. However, films deposited at a temperature of 300°C did not show any changes in the compressive stress or resistivity after annealing. The results of this study can be used to deposit RuO_x thin films with low resistivity and minimal stresses.     

Tungsten–carbon films prepared by reactive sputtering from argon–benzene discharges

Tungsten–carbon thin films have been deposited by reactive (Ar+C₆H₆) DC magnetron sputtering onto various substrates. Deposition onto glass, monocrystalline silicon, tantalum and stainless steel at room temperature yielded W–C films, having XRD patterns corresponding to the structure of heavily disordered W₂C or WC_1−x carbides. The samples deposited upon the Au or Cu foils were nanocrystalline cubic WC_1−x with the grain size of 2.9 nm. Disordered tungsten–carbon films were stable up to 1200°C. Microhardness of the films with disordered W₂C phase was about 5–6 GPa while that of the films with disordered WC_1−x phase was about 17 GPa. The characteristics of films can be understood considering the effects of the incorporation of free carbon and/or carbon–hydrogen fragments into the tungsten carbide layer.     

Preparation and characterization of C60S16 and C70S48 thin films

In this study, we have investigated different methods for preparation of thin films of C₆₀ and C₇₀-sulfur compounds. Films of good quality were obtained by reaction of amorphous C₆₀ and C₇₀ films with a saturated sulfur solution in toluene at 40°C or with saturated sulfur vapour at a temperature of 140°C for several hours. The quality of the fullerene-sulfur films were strongly dependent on the microstructure of the initially deposited fullerene film and the synthesis temperature. X-ray diffraction analyses showed that both methods lead to the formation of films consisting of C₆₀S₁₆ and C₇₀S₄₈ (space groups C 2/c and Amm2, respectively). C₆₀S₁₆ films synthesised on Al₂O₃(012) and Si(100) substrates were texture-free while C₇₀S₄₈ films typically exhibited a preferential (100) orientation. The films were also characterised by Raman and IR- spectroscopy, which confirmed that the interactions between the fullerene molecules and the S₈ rings are weak. The fullerene-sulfur compounds were found to be unstable at high vacuum conditions. Both materials C₆₀S₁₆ and C₇₀S₄₈ are non-conductive at room temperature with conductivities less then 10⁻⁵ (Ω/cm).     

Preparation and optical properties of sol–gel derived Er-doped Al2O3–Ta2O5 films

Thin films of the system xAl₂O₃–(100 − x)Ta₂O₅–1Er₂O₃ were prepared by a sol–gel method and a dip-coating technique. The influences of the composition and the crystallization of the films on Er³⁺ optical properties were investigated. Results of X-ray diffraction indicated that the crystallization temperature of Ta₂O₅ increased from 800 to 1000 °C with increased values of x. In crystallized films, the intensities of the visible fluorescence and upconversion fluorescence tend to decrease with an increase in x values, due to the high phonon energy of Al₂O₃; the strongest fluorescence is observed in a crystallized film for x = 4 heat treated at 1000 °C. In amorphous films obtained by heat treatment at relatively low temperatures the Er³⁺ fluorescence could not be observed because strong fluorescence from organic residues remaining in the films thoroughly covered the Er³⁺ fluorescence. On the other hand, the Er³⁺ upconversion fluorescence in the amorphous films was observed to be stronger than that in the crystallized films. The strongest upconversion fluorescence is observed in an amorphous film for x = 75 heat treated at 800 °C.     

Photoluminescence properties of the Yb:Er co-doped Al2O3 thin film fabricated by microwave ECR plasma source enhanced RF magnetron sputtering

The Yb:Er co-doped Al₂O₃ thin film was deposited on oxidized silicon wafers by microwave ECR plasma source enhanced RF magnetron sputtering, and annealed from 800 °C to 1000 °C. The photoluminescence at 1.53 μm of thin film was obtained under room temperature. The mixture phase structure of γ and θ is observed by XRD, and the compositions of the thin film are investigated by EPMA. The maximum PL intensity was achieved with O₂:Ar at 1:1, annealing temperature at 900 °C, and experimental ratio of Yb:Er at 1:3.6. The energy transfer mechanism between Er and Yb ions is supported by theoretical analysis and experiment results.     

Physics of very thin ITO conducting films with high transparency prepared by DC magnetron sputtering

The preparation of very thin indium tin oxide (ITO) films with extremely high transparency and suitable resistivity, as well as resistivity stability for long term use, is described. In order to obtain these properties, amorphous suboxide films were first prepared and then annealed. Suboxide films with a thickness of 20 to 30 nm were prepared on PET film and glass substrates at a temperature of 60 °C using In₂O₃---SnO₂ targets with a SnO₂ content of 0 to 10 wt% by DC magnetron sputtering in a pure argon gas atmosphere. The films were annealed at a temperature of 150 °C for 1 to 100 h in air. The resistivity of films on PET films was, depending on the SnO₂ content, on the order of 10⁻³ ω cm. An average transmittance above 97% in the visible wavelength range and a resistivity of about 4 × 10⁻³ ω cm, as well as resistivity stability, were attained in ITO films with a SnO₂ content of about 1 wt% prepared on PET films by the low-temperature process. It is thought that these properties result from crystallization which occurred during the annealing, duration up to about 25 h.     

Improved fatigue properties of lead zirconate titanate films made on oxygen-implanted platinum electrodes

Pb(Zr_0.3Ti_0.7)O₃ (PZT) thin film capacitors fabricated on an oxygen-implanted Pt bottom electrode were studied. Oxygen was implanted at a low acceleration voltage (40 kV) and dose (1×10¹⁵ cm⁻²). Structural examination by grazing-incident X-ray diffraction (GIXD) and chemical analysis by X-ray photoelectron spectroscopy (XPS) revealed that the implantation generated a very thin amorphous top surface layer (approx. 20 nm), which contained approximately 7% of oxygen that stayed in the film in the form of PtO bonding. The amorphous layer, however, resumed the crystalline structure accompanied by the dissociation of PtO under the rapid thermal annealing at 600 °C for 5 min. The remnant polarization of sol–gel derived Pb(Zr_0.3Ti_0.7)O₃ (PZT) films fabricated on the oxygen-implanted Pt was slightly reduced from 11.92 μC/cm² for the PZT capacitors fabricated on a Pt electrode without implanted oxygen to 9.07 μC/cm². Nevertheless, the fatigue endurance was significantly increased. The switching polarization of PtO_x/PZT/Pt (O-implanted) capacitors remained within 95% of the starting value after 4×10¹⁰ switching cycles, which is comparable to that of PZT capacitors made with other conducting oxides.     

Atomic layer deposition growth of zirconium doped In2O3 films

Zirconium doped indium oxide thin films were deposited by the atomic layer deposition technique at 500 °C using InCl₃, ZrCl₄ and water as precursors. The films were characterised by X-ray diffraction, energy dispersive X-ray analysis and by optical and electrical measurements. The films had polycrystalline In₂O₃ structure. High transparency and resistivity of 3.7×10⁻⁴ Ω cm were obtained.     

MBE growth and characterization of buried silicon oxide films on Si(100)

Silicon molecular beam epitaxy (Si-MBE) has been used to produce silicon oxide (SiO_x) films by evaporating Si on a heated Si(100) substrate in an ultra high vacuum system with an O₂ pressure of 10⁻⁶ to 10⁻⁴ mbar. Then the SiO_x films were overgrown with pure Si. The influence of the substrate temperature, the O₂ pressure and the Si deposition rate on the oxygen content in the SiO_x films and on the crystalline quality of the Si top-layer was investigated by Rutherford backscattering spectrometry and ion channeling. Epitaxial growth of the Si top-layer was observed up to a maximum concentration of ≈20 at.% oxygen content in the SiO_x film. Cross-sectional transmission electron microscopy shows that the structure of the SiO_x film changes duringa subsequent annealing procedure. Electron energy loss spectrometry proves that amorphous SiO₂ is formed and the development of holes indicates that the density of the as-grown SiO_x film is much lower than that of SiO₂. The specific for the as-grown SiO_x films was determined by I–V measurements.