加磁场对GZO薄膜结构及光电性能的影响

采用射频磁控溅射法在玻璃基底上制备了Ga掺杂ZnO (GZO)薄膜,在传统磁控溅射系统中引入外加磁场,探究了磁场强度变化对GZO薄膜晶体结构和光电性能的影响.结果表明:所制得的GZO薄膜结构均为六角纤锌结构且在[002]方向沿C轴择优取向;外加磁场强度对薄膜的光电性能具有较大影响,在可见光范围内,薄膜的平均透光率超过93;,并出现了Moss-Burstein效应;薄膜的电学性能得到提升,其电阻率从4.96×10-3 Ω·cm降至3.17×10-4Ω·cm,霍尔迁移率从7.36cm2 ·V-1 ·S-1增至9.53 cm2·V-1·S-1.     

绒面ZnO透明导电薄膜

采用孪生ZnO (Al2 O3 ∶2 % )对靶直流磁控溅射制备高透过率、高电导率的平面ZnO薄膜 (迁移率为 5 .5 6cm2 /V·s,载流子浓度为 4 .5 7× 10 2 0 cm-3 ,电阻率为 2 .4 6× 10 -3 Ω·cm ,可见光范围 (380～ 80 0nm)平均透过率大于 85 % )。用酸腐蚀的方法 ,可以获得绒面效果 ,而反应气压对绒面效果没有影响 ,薄膜的电学特性没有变化 ,绒面对光散射作用增强 ,导致相对于平面ZnO薄膜的透过率要低一些 (可见光范围平均透过率大于 80 % )。     

衬底温度对MOCVD-ZnO薄膜特性的影响

利用金属有机物化学气相沉积(MOCVD)生长技术,制备本征ZnO薄膜,并研究薄膜的结构、形貌及光电等性能.结果表明:衬底温度对ZnO薄膜的微观结构、电学、光学及表面形貌等有显著影响.在衬底温度为180℃时获得电阻率为2.17×10-2Ω·cm.平均透过率为85;的低电阻、高透过率、结晶质量高、表面呈绒面结构的本征ZnO薄膜.对本征ZnO薄膜进一步掺杂和结构优化有望用于硅薄膜太阳能电池的前电极.     

薄膜厚度对MOCVD法沉积ZnO透明导电薄膜的影响

本文研究了薄膜厚度对MOCVD技术制备未掺杂ZnO薄膜的微观结构和电学特性影响.XRD和SEM的研究结果表明,随着薄膜厚度的增加,ZnO薄膜(110)峰趋于择优取向,且晶粒逐渐长大,薄膜从球状和细长棒状演变为具有类金字塔绒面结构特征的ZnO薄膜;Hall测量表明,较厚的ZnO薄膜有助于提高薄膜电学特性,可归于晶粒长大和晶体质量提高.40min沉积时间(膜厚为1250nm)制备出的ZnO薄膜具有明显绒面结构,其晶粒尺寸为300～500nm,电阻率为7.9×10-3Ω·cm,迁移率为26.8cm2/Vs.     

Ga掺杂浓度对溶胶-凝胶法制备GZO薄膜光电性能的影响

采用溶胶-凝胶法在玻璃基片上制备掺镓氧化锌透明导电薄膜,用X射线衍射仪、扫描电子显微镜、紫外可见光分光光度计、霍尔效应仪等测试分别表征GZO薄膜的晶体结构、表面形貌、光电性能等,研究Ga掺杂量对GZO薄膜性能的影响.结果表明:所制备的GZO薄膜均为六方纤锌矿结构并有沿c轴择优生长趋势,随着Ga掺杂量的增加,薄膜透过率先增加再减小,当Ga掺杂量为4at;时透过率最高,可见光区平均透过率达97.4;,薄膜电阻率则随掺杂量增加而下降,在Ga掺杂量为5at;时达最小值7.62×10-3 Q·cm.     

利用直流磁控溅射法在柔性衬底上制备ZnO: Zr新型透明导电薄膜

室温下利用直流磁控溅射法在有ZnO缓冲层的柔性衬底 PET上制备出了可见光透过率高、电阻率低的掺锆氧化锌(ZnO: Zr)透明导电薄膜,研究了厚度对ZnO: Zr薄膜结构及光电性能的影响.结果表明,ZnO: Zr薄膜为六方纤锌矿结构的多晶薄膜.实验获得ZnO: Zr薄膜的最小电阻率为2.4×10-3 Ω·cm,其霍尔迁移率为18.9 cm2·V-1·s-1 ,载流子浓度为2.3×1020 cm-3.实验制备的ZnO: Zr薄膜具有良好的附着性能,其可见光平均透过率超过92;.     

溅射气压对直流电源磁控溅射制备掺铝氧化锌薄膜性能的影响

以ZnO∶Al2O3(2wt%)陶瓷为溅射靶材,采用直流磁控溅射的方法,在普通玻璃衬底上制备ZnO∶Al(AZO)薄膜,研究了溅射气压对AZO薄膜的结构特性、表面形貌及其光电性的影响。XRD和SEM测试表明所有样品均为多晶六角纤锌矿结构,薄膜呈(002)晶面择优生长。用体积百分比为0.5%稀盐酸对制备的AZO薄膜进行腐蚀制绒,腐蚀后其表面形貌随溅射气压的不同而改变。在适当溅射气压下(～1.5m Torr)制备的薄膜,通过溅射后腐蚀工艺,可获得表面形貌具有特征陷光结构的AZO薄膜,其表面呈现"弹坑"状,薄膜的绒度随表面形貌的不同而变化。同时通过优化制备工艺,所有溅射气压下制备的AZO薄膜在可见光及近红外范围的平均透过率大于80%,电阻率低于8.5×10-4Ω·cm,可以满足硅基薄膜太阳电池对透明前电极光电性能的要求。     

射频功率对ITZO薄膜结构、形貌及光电特性的影响

在室温下采用射频磁控溅射方法在玻璃衬底上制备了200 nm厚的铟锡锌氧化物(ITZO)薄膜,研究了不同功率下薄膜结构、形貌、光学和电学性能的变化规律.结果表明,ITZO薄膜为非晶薄膜并且有着良好的光电特性,其平均光学透过率超过了84;,载流子霍尔迁移率高达24 em2·V-1·s-1.随着射频功率从50 W上升到100 W,薄膜的光学带隙从3.68 eV逐渐增加到3.76 eV.研究发现,薄膜的电学性能强烈依赖于射频功率.随着功率的增加,薄膜的电学性能呈现出先变好后变差的变化规律.当射频功率为80 W时,ITZO薄膜拥有最佳的电学性能,其电阻率为3.80×10-4Ω·cm,载流子浓度为6.45×1020 cm-3,霍尔迁移率为24.14 cm2·V-1· s-1.     

衬底温度对直流反应磁控溅射法制备的N掺杂p型ZnO薄膜性能的影响

利用直流反应磁控溅射法(纯金属锌作为靶材,Ar-N2-O2混合气体作为溅射气体)在石英玻璃衬底上制备了N掺杂p型ZnO薄膜.通过XRD、Hall和紫外可见透射谱分别研究了衬底温度对ZnO薄膜结构性能、电学性能和光学性能的影响.XRD结果显示所有制备的薄膜都具有垂直于衬底的c轴择优取向,并且随着衬底温度的增加,薄膜的晶体质量得到了提高.Hall测试表明衬底温度对p型ZnO薄膜的电阻率具有较大影响,400℃下生长的p型ZnO薄膜由于具有较高的迁移率(1.32 cm2/Vs)和载流子浓度(5.58×1017cm-3),因此表现出了最小的电阻率(8.44Ω·cm).     

B掺杂对平面结构MOCVD-ZnO薄膜性能的影响

本文研究了B2H6掺杂流量(B掺杂)对平面结构MOCVD-ZnO薄膜的微观结构和光电性能影响.XRD、SEM和AFM测试的研究结果表明,玻璃衬底上制备的ZnO薄膜具有(002)峰择优取向的平面结构,B掺杂使薄膜的球状晶粒尺寸变小,10 sccm流量时晶粒尺寸为～15 nm.ZnO:B薄膜的最小电阻率为5.7×10-3Ω·cm.生长的ZnO薄膜(厚度d=1150 nm)在400～900 nm范围的透过率为82;～97;,且随着B2H6掺杂流量增大,光学吸收边呈现蓝移(即光学带隙Eg展宽)现象.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

Crystal structures of the cis and trans isomers of a tetrathia[3.3.3.3]cyclophane

Both the cis and trans isomers of 3,11,18,26-tetrathiatricyclo[26.2.2.1^5,9.2^13,16.1^20,24] hexatriaconta-5,7,9,20,22,24-hexene have been prepared and structurally characterized. Each of these centrosymmetric tetrathia dimers includes two cyclohexane rings in chair conformations with either 1,4-cis or 1,4-trans bonding and two meta-substituted benzene rings. The cis isomer packs into the monoclinic space group P2₁/a with a = 10.485(3)Å, b = 10.3956(18)Å, c = 14.1343(10)Å, = 105.200(13)°, Z = 2 and refined to an R factor of 0.046. The trans isomer crystallizes in the monoclinic space group P2₁/c with a = 10.7217(12)Å, b = 5.6797(7)Å, c = 25.415(5)Å, = 96.001(12)°, Z = 2 and refined to an R factor of 0.043. In the cis structure each benzene ring faces a cyclohexane ring while in the trans structure the cyclohexane rings face one another.     

电沉积法制备ZnO纳米棒阵列及其发光特性

本文以掺F的SnO2导电玻璃为基板,以硝酸锌水溶液为电解液,采用三电极恒电位体系电沉积制备ZnO纳米棒阵列,系统考察了硝酸锌浓度和沉积电位等工艺参数对ZnO纳米棒阵列的微观形貌及其发光性能的影响规律.结果表明,硝酸锌浓度和沉积电位对纳米棒阵列的形貌有显著影响,控制适宜的工艺条件可以制备出直径分布均匀、结晶性好且纯度高的六方纤锌矿ZnO纳米棒阵列.荧光光谱分析表明,电沉积制备出的ZnO纳米棒阵列在385 nm附近有一个强荧光发射峰,且发光性能稳定、对纳米棒阵列微观形貌的细微变化不敏感,使其在发光二极管和激光器等领域具有广阔的应用前景.     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

Phase Properties of Hexanedioldiacrylate/E7 Blends

Abstract

Equilibrium phase diagrams of uncured and UV-cured difunctional hexanedioldiacrylate and the eutectic mixture of low molecular weight liquid crystals E7 are established by polarized optical microscopy and differential scanning calorimetry. Data are analyzed using the Maier-Saupe model of nematic order. In the case of the uncured system the Flory-Huggins free energy of isotropic mixing is applied while for the cured system, the Flory-Rehner elastic free energy model is used. A good correlation between experimental and theoretical phase diagrams is found in both systems.     

C–H...O,C–H...π and π–π stacking interactions in 3-(2,4-dimethylphenyloxymethyl)-3,4-dihydroisocoumarin

3-(2,4-Dimethylphenyloxymethyl)-3,4-dihydroisocoumarin (C₁₈H₁₈O₃) was prepared by the alkylation of o-lithio N-methyl benzamide with 2-(2,4-dimethylphenoxy)methyl oxirane, followed by alkaline hydrolysis. The compound crystallizes in the orthorhombic space group Pbca with unit cell parameters : a = 8.239(2) Å, b = 14.918(5) Å, c = 24.831(9) Å, Z = 8. The crystal structure was solved by direct methods and refined to R = 0.0514 for 1564 observed reflections. The heterocyclic ring adopts a distorted half-chair conformation. Molecules are connected by π–π interactions between phenyl rings of the isocoumarin nucleus forming dimers. Dimers are connected via C–H...O hydrogen bonds forming chains. Further intermolecular C–H...π hydrogen bonds link the dimer chains to form supramolecular structure.     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

A new method for the investigation of orientation relationships in meteoritic plessite

The orientation relationship (OR) between the bcc and fcc phase in the plessite microstructure of the iron meteorites Watson, Agpalilik and Gibeon has been analysed in a scanning electron microscope using electron back‐scattered diffraction (EBSD). A very strong OR exists, independently on the analysed plessite type and the observed spreading of single orientation data. The agreement between the experimental orientation distribution and existing models varies for each meteorite. The black plessite in the Agpalilik corresponds to the Nishiyama‐Wassermann model whereas the duplex plessite of the Gibeon meteorite shows an OR close to the Kurdjumov‐Sachs model. The Watson meteorite is strongly deformed so that a general OR is difficult to determine due to the blurred experimental orientation distribution. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.