MgF2对Mn4+掺杂锗酸盐红色荧光粉发光的影响

3.5MgO·0.5MgF₂·GeO₂：Mn⁴⁺作为优异热稳定性和良好发光性能的红色荧光粉而被市场应用,然而,该粉体中MgF₂的作用影响机理尚不明晰,阻碍其性能进一步优化和发展。采用高温固相法制备了系列Mn⁴⁺激活的锗酸盐荧光粉,通过对比加入MgF₂、H₃BO₃（助熔剂）,研究了该粉体的结构、形貌、发光性能等变化规律,阐明了MgF₂的发光影响作用。研究表明,加入MgF₂、H₃BO₃和不加任何助熔剂时的样品,其最佳烧结温度分别为1 150、1 250和1 350 ℃,上述温度下发光强度均为最佳值,其中加入MgF₂、H₃BO₃的样品在最佳温度处生成了纯相。MgF₂的添加,一方面同H₃BO₃一样作为助熔剂对生成纯相、提高样品结晶度起了积极的作用;另一方面,通过研究分析,确认F^-离子成功掺杂进入晶格,促使样品生成的晶体结构为Mg₁₄Ge₅（O, F）₂₄。加入MgF₂、H₃BO₃在最佳烧结温度的样品的荧光寿命分别为0.93和0.75 ms。     

低温凝胶燃烧法合成Y2O3∶Er3+，Yb3+纳米晶上转换发光材料

分别以柠檬酸和甘氨酸为燃烧剂,采用低温凝胶燃烧法合成了Er³⁺、Yb³⁺共掺Y₂O₃纳米晶粉体。通过TG-DSC、XRD、SEM等分析手段对两种燃烧剂所对应的反应过程及纳米晶粉体的物理性能进行了分析,结果表明甘氨酸法具有更高的反应效率、更好的粉体分散性及粒径均匀性。在980 nm激光二极管(LD)激发下,对甘氨酸法所得样品的上转换发光性能分析表明,绿光和红光发射谱带分别来自于Er³⁺的⁴S_3/2/ ²H_11/2→ ⁴I_15/2和⁴F_9/2→ ⁴I_15/2跃迁。此外,对Er³⁺和Yb³⁺掺杂浓度、粉体煅烧温度对纳米晶样品上转换发光性能的影响进行了讨论。     

电荷补偿对Ba2ZnGe2O7∶Bi3+荧光粉发光性质的影响

采用高温固相法制备了2个系列的荧光粉样品：Ba_2-xZnGe₂O₇∶xBi³⁺(系列Ⅰ)和Ba_1.994-yK_yZnGe₂O₇∶0.006Bi³⁺(系列Ⅱ)。X射线衍射(XRD)测试结果表明,少量Bi³⁺、K⁺的掺杂不会明显改变材料的物相结构。样品的荧光光谱测试结果表明,虽然2个系列样品的发光光谱都随组成成分变化有少量变化,但发光颜色基本上均为黄绿色。在358 nm的激发下,荧光粉的发射光谱呈现一个峰值在 500 nm 的宽发射带,归属于 ³P₁→^1S₀能级跃迁。在 500 nm 监测下,荧光粉的最强激发峰位于 358 nm,归属于¹S₀→³P₁能级跃迁,此外还有一个位于320 nm的肩峰归属于O^2--Bi³⁺电荷转移带。系列Ⅰ样品的光谱数据结果指出,Bi³⁺的最佳掺杂量x为0.006。在该基质中,Bi³⁺掺杂取代Ba²⁺属于不等价取代,会在晶格中产生Ba²⁺空位或间隙O^2-,对材料的发光强度产生负面影响。对此,采用K⁺与Bi³⁺协同掺杂起到电荷补偿的作用,填补Ba²⁺空位或捕获间隙O^2-缺陷。空位被填补或间隙被捕获均减少了晶格畸变,从而使发光强度明显提高。系列Ⅱ样品的光谱数据表明,完全电荷补偿的荧光粉样品相比于没有掺K⁺的样品,其发光强度提高了约2.5倍。     

硼酸对Sr2CeO4荧光粉的物相组成和发光性质的影响

采用正交试验确立了高温固相法合成Sr₂CeO₄的主要影响因素。研究了H₃BO₃和n_Sr/n_Ce(物质的量的比)对Sr₂CeO₄物相组成和发光强度的影响。XRD结果表明保持n_Sr/n_Ce为5.5和添加6.5wt%的H₃BO₃，有利于形成良好的Sr₂CeO₄晶体结构和大幅度提高Sr₂CeO₄的发光强度。荧光光谱测试表明助熔剂法合成样品的发光强度分别比传统固相法合成和溶胶-凝胶法提高了201.2%和15.7%。     

ZnAl2O4∶Mn4+材料的制备及发光性能

以共沉淀法与煅烧法联用,成功制备了一系列ZnAl₂O₄∶xMn⁴⁺样品。通过扫描电镜和X射线粉末衍射测试研究了样品的形貌和物相特征,结果表明尖晶石结构的ZnAl₂O₄中[AlO₆]的八面体位可以有效被Mn⁴⁺替代。通过荧光激发和发射光谱研究了样品的发光性能,发现Mn⁴⁺在ZnAl₂O₄体系中掺杂可以显示出明亮的红色发光(发射峰值位于680 nm处)。比较不同Mn⁴⁺浓度(Mn与Al的物质的量之比)掺杂样品的发光强度时发现,Mn⁴⁺最佳掺杂浓度为0.06%。通过德克斯特公式分析了发光强度与浓度关系,探究浓度猝灭机制,结果表明最邻近离子之间能量传递造成Mn⁴⁺浓度猝灭的发生。为了提高Mn⁴⁺的发光强度,选择了7种金属离子(Li⁺、Na⁺、K⁺、Ca²⁺、Sr²⁺、Sn²⁺和Ga³⁺)与Mn⁴⁺共掺杂进入ZnAl₂O₄基质中,其中效果较突出的为Li⁺和Ga³⁺,其共掺杂使Mn⁴⁺发光强度分别增强0.6倍和1倍。     

ZnAl2O4∶Mn4+材料的制备及发光性能

以共沉淀法与煅烧法联用,成功制备了一系列ZnAl₂O₄∶xMn⁴⁺样品。通过扫描电镜和X射线粉末衍射测试研究了样品的形貌和物相特征,结果表明尖晶石结构的ZnAl₂O₄中[AlO₆]的八面体位可以有效被Mn⁴⁺替代。通过荧光激发和发射光谱研究了样品的发光性能,发现Mn⁴⁺在ZnAl₂O₄体系中掺杂可以显示出明亮的红色发光(发射峰值位于680 nm处)。比较不同Mn⁴⁺浓度(Mn与Al的物质的量之比)掺杂样品的发光强度时发现,Mn⁴⁺最佳掺杂浓度为0.06%。通过德克斯特公式分析了发光强度与浓度关系,探究浓度猝灭机制,结果表明最邻近离子之间能量传递造成Mn⁴⁺浓度猝灭的发生。为了提高Mn⁴⁺的发光强度,选择了7种金属离子(Li⁺、Na⁺、K⁺、Ca²⁺、Sr²⁺、Sn²⁺和Ga³⁺)与Mn⁴⁺共掺杂进入ZnAl₂O₄基质中,其中效果较突出的为Li⁺和Ga³⁺,其共掺杂使Mn⁴⁺发光强度分别增强0.6倍和1倍。     

反应温度对微波水热法合成Bi2WO6粉体及光催化性能影响的研究

以Na₂WO₄·2H₂O和Bi(NO₃)₃·5H₂O为原料,用微波水热法在140~200 ℃保温1 h合成出不同形貌的正交晶相粉体。利用 XRD、FE-SEM、BET、DRS等分析手段表征了Bi₂WO₆粉体,以RhB溶液为目标降解物,对不同反应温度下合成粉体的光催化性能进行了研究,结果表明：反应温度对合成Bi₂WO₆粉体的物相、形貌及光催化性能均有较大影响,180 ℃时合成的绒线团状Bi₂WO₆粉体比表面积为25.63 m²·g^-1,禁带宽度为2.92 eV,因光在粉体催化剂内产生了漫反射,光催化效果最佳,在可见光照射下3h时RhB溶液降解率达到了96%,紫外光照射下2 h时RhB溶液降解率达到了98%以上。     

稀土掺杂Lu3Al5O12荧光粉的发光特性及能量传递

采用高温固相法制备了Ce、Sm共掺Lu₃Al₅O₁₂荧光粉。通过X射线衍射分析、荧光光谱分析研究了样品的结构、发光特性,并通过理论计算研究了能量传递效率、能量传递的临界距离以及能量传递方式。X射线衍射分析表明所制备的荧光粉具有单一的石榴石结构;荧光光谱分析表明,在464 nm蓝光激发下,Sm³⁺的引入可增加Lu₃Al₅O₁₂：Ce,Sm发射光谱中红光成分,并且随着Sm³⁺浓度的增加,Ce³⁺发光强度逐渐减弱。计算出Ce³⁺、Sm³⁺之间的能量传递效率高达77.42%,确定了Ce³⁺、Sm³⁺之间的能量传递机制为偶极-偶极相互作用。     

La7O6(BO3)(PO4)2:Eu3+/Tb3+荧光材料的制备及其光致发光性能

采用优化的高温固相方法制备了稀土离子Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂系荧光材料,并对其物相行为、晶体结构、光致发光性能和热稳定性进行了详细研究。结果表明,La₇O₆（BO₃）（PO₄）₂：Eu³⁺材料在紫外光激发下能够发射出红光,发射光谱中最强发射峰位于616 nm处,为⁵D₀→⁷F₂特征能级跃迁,Eu³⁺的最优掺杂浓度为0.08,对应的CIE坐标为（0.610 2,0.382 3）;La₇O₆（BO₃）（PO₄）₂：Tb³⁺材料在紫外光激发下能够发射出绿光,发射光谱中最强发射峰位于544 nm处,对应Tb³⁺的⁵D₄→⁷F₅能级跃迁,Tb³⁺离子的最优掺杂浓度为0.15,对应的CIE坐标为（0.317 7,0.535 2）。此外,对2种材料的变温光谱分析发现Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂荧光材料均具有良好的热稳定性。     

红色长余辉荧光粉Ca2Zn4Ti16O38:Pr3+的水热辅助合成及发光性质

采用水热法辅助合成了纯相Ca₂Zn₄Ti₁₆O₃₈:Pr³⁺荧光粉,初始n_Ca:n_Zn:n_Ti=2:4.1:15,煅烧条件为1 050 ℃空气气氛烧结5 h.并以X射线衍射、扫描电镜、紫外可见漫反射光谱和荧光光谱表征了样品的物相组成、微观形貌和光谱性质.合成的荧光粉在高温煅烧后仍较好地保持了球形的微观形态,优化的Pr³⁺掺杂浓度为0.015.Ca₂Zn₄Ti₁₆O₃₈:Pr³⁺荧光粉在471 nm波长激发下发射红光,发射谱通过高斯分峰拟合得到位于605、620和645 nm的3个发射峰,分别对应于Pr³⁺的¹D₂→³H₄,³P₀→³H₆和³P₀→³F₂跃迁.在471 nm波长激发下,Ca₂Zn₄Ti₁₆O₃₈:Pr³⁺的614 nm红光发射表现出超长余辉特性,表明该荧光粉是一种能被可见光有效激发的红色长余辉荧光粉.     

一维纳米Co_3O_4,Ag/Co_3O_4及CuO/Co_3O_4的合成与电催化性能(英文)

采用水热合成法制备了Co3O4及复合Ag/Co3O4、CuO/Co3O4一维纳米产品。用XRD,FE-SEM和TEM手段对产品进行了表征。采用循环伏安法研究了合成产品修饰的玻碳电极在碱性溶液中对对硝基苯酚的电催化还原性能。与裸玻碳电极相比,1mmol·L-1的对硝基苯酚在用Co3O4、特别是CuO/Co3O4修饰的玻碳电极上还原的峰电流明显增大,用Ag/Co3O4(Ag/Co原子比分别为1∶5和2∶5)修饰的玻碳电极催化还原对硝基苯酚时,尽管还原峰电流增大不是太大,但其峰电位明显降低(分别降低0.265和0.371V)。     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Ni-P-Zn3(PO4)2(ZnSnO3、ZnSiO3)纳米复合化学镀层性质和组成的研究

研究了温度、时间、浓度等对Ａ３钢片上Ｎi-P-Zn3(PO4)2、Ni-P-ZnSnO3和Ｎi-P-ZiSiO3纳米复合合化学镀层外貌的影响,用扫描电子显微镜（ＳＥＭ）观察外貌、称重法测定厚度;通过１０％ＮaCl溶液、１％Ｈ２Ｓ气体加速腐蚀试验,１０％ＣuSO4溶液点滴试验等多种手段测定其耐腐蚀性能,用Ｘ－射线光电子谱（ＸＰＳ）及俄歇电子能谱（ＳＥＳ）测定其价态组成,结果表明：在最佳施镀条件下,可得光亮、致密、耐腐蚀性强于Ａ３钢、磷化膜及Ｎi-P镀层的纳米复合化学镀层,镀层的原子百分组成约为（％）：Ｎi-P-Zn3(PO4)2:Ni70.00,P12.47,Zn3(PO4)213.93,C3.6;Ni-P-ZnSnO3;Ni77.56,P10.00,ZnSnO39.84,C2.6;Ni-P-NiSiO3,Ni83.00,P10.96,ZnSi5.15,C0.89.     

Direct dynamics studies for the reactions of CF3CHFCF3 and CF3CF2CHF2 with H atoms

The rate constants of the hydrogen abstraction reactions of CF₃CHFCF₃ + H (R1) and CF₃CF₂CHF₂ + H (R2) have been calculated by means of the dual-level direct dynamics method. Optimized geometries and frequencies of stationary points and extra points along the minimum-energy path (MEP) are obtained at the MPW1K/6-311+G(d,p) level, and the classical energetic information is further corrected with the interpolated single-point energy (ISPE) approach by the G3(MP2) level of theory. Using the canonical variational transition state theory (CVT) with small-curvature tunneling corrections (SCT), the rate constants are evaluated over a wide temperature range of 200-2000 K. The calculated CVT/SCT rate constants are in good agreement with available experimental values. It is found that the variational effect is very small and almost negligible over the whole temperature region. However, the small-curvature tunneling correction plays an important role in the lower temperature range. Furthermore, the heats of formation of species CF₃CF₂CHF₂ (SC₁ or SC₂) and CF₃CF₂CF₂ are studied using isodesmic reactions to further elucidate the thermodynamic properties.     

Na5P3O10-Ca(OH)2-CO2-H2O体系纳米CaCO3的成核与生长

通过化学分析、SEM显微分析技术,结合Rosin-Ramiler概率统计理论,从介观层次研究Na5P3O10-Ca(OH)2-CO2-H2O体系纳米CaCO3的合成反应及其成核和生长过程。结果表明,Na5P3O10对Ca(OH)2的碳化反应具有抑制作用。随着[Na5P3O10]的增加,体系中CaCO3的成核速率B^0逐渐增大。在[Na5P3O10]＝0ppm时,CaCO3结晶的生长由长程扩散和凝聚生长控制;[Na5P3O10]=380.4,760.9ppm时,前期受短程扩散和界面反应控制、后期受长程扩散控制。Na5P3O10的存在,抑制了纳米CaCO3的晶体生长。     

Determination of the enthalpy of fusion of K3TaF8 and K3TaOF6

The areas of the fusion and crystallization peaks of K₃TaF₈ and K₃TaOF₆ have been measured using the DSC mode of the high-temperature calorimeter (SETARAM 1800 K). On the basis of these quantities and the temperature dependence of the used calorimetric method sensitivity, the values of the enthalpy of fusion of K₃TaF₈ at temperature of fusion 1039 K: Δ_fusH_m(K₃TaF₈; 1039 K) = (52 ± 2) kJ mol⁻¹ and of K₃TaOF₆ at temperature of fusion 1055 K: Δ_fusH_m(K₃TaOF₆; 1055 K) = (62 ± 3) kJ mol⁻¹ have been determined.     

A fast synthesis for Zintl phase compounds of Na3SbTe3, NaSbTe2 and K3SbTe3 by microwave irradiation

The microwave irradiation technique was used to prepare three Zintl phase compounds Na₃SbTe₃, NaSbTe₂ and K₃SbTe₃. The as-prepared products were analyzed and characterized by XRD, EDX and SEM techniques. Higher microwave oven power and shorter irradiation time are required for the synthesis of Na₃SbTe₃, whereas lower oven power and longer irradiation time are needed for NaSbTe₂. Moderate microwave irradiation conditions facilitate the formation of pure K₃SbTe₃. Pure phase of Na₃SbTe₃ are directly obtained by this technique for the first time. Compared with the traditional high-temperature solid-state synthesis, the microwave reaction required a considerable shortened reaction time for the preparation of the three Zintl compounds. The initial driving force for these reactions originates from the interaction of microwave electric field with alkali metals (Na and K) and Sb powders.     

Sol-gel synthesis of K3InF6 and structural characterization of K2InC10O10H6F9, K3InC12O14H4F18 and K3InC12O12F18

K₃InF₆ is synthesized by a sol-gel route starting from indium and potassium acetates dissolved in isopropanol in the stoichiometry 1:3, with trifluoroacetic acid as fluorinating agent. The crystal structures of the organic precursors were solved by X-ray diffraction methods on single crystals. Three organic compounds were isolated and identified: K₂InC₁₀O₁₀H₆F₉, K₃InC₁₂O₁₄H₄F₁₈ and K₃InC₁₂O₁₂F₁₈. The first one, deficient in potassium in comparison with the initial stoichiometry, is unstable. In its crystal structure, acetate as well as trifluoroacetate anions are coordinated to the indium atom. The two other precursors are obtained, respectively, by quick and slow evaporation of the solution. They correspond to the final organic compounds, which give K₃InF₆ by decomposition at high temperature. The crystal structure of K₃InC₁₂O₁₄H₄F₁₈ is characterized by complex anions [In(CF₃COO)₄(OH_x)₂]^(5−2x)− and isolated [CF₃COOH_2−x]^(x−1)− molecules with x=2 or 1, surrounded by K⁺ cations. The crystal structure of K₃InC₁₂O₁₂F₁₈ is only constituted by complex anions [In(CF₃COO)₆]³⁻ and K⁺ cations. For all these compounds, potassium cations ensure only the electroneutrality of the structure. IR spectra of K₂InC₁₀O₁₀H₆F₉ and K₃InC₁₂O₁₂F₁₈ were also performed at room temperature on pulverized crystals.     

B2O3-Bi2O3-ZnO-Al2O3玻璃助烧剂对BaTiO3陶瓷烧结条件、晶体结构和介电性能的影响

通过调节B₂O₃‐Bi₂O₃‐ZnO‐Al₂O₃(BBZA)玻璃的添加量研究其对钛酸钡(BaTiO₃)陶瓷烧结条件、晶体结构和介电性能的影响。结果表明：添加适量的BBZA玻璃能够有效地将BaTiO₃陶瓷烧结温度由1350℃降至950℃,并使其致密化。同时,添加BBZA玻璃后,BaTiO₃的晶体结构随着烧结温度的升高而发生转变(立方相→四方相)。另外,BBZA玻璃的引入使BaTiO₃陶瓷的居里峰得到了有效的抑制和拓宽。陶瓷微观形貌显示,玻璃相均匀分布在BaTiO₃晶粒表面。优化的BaTiO₃陶瓷制备条件如下：BBZA添加量(质量分数)为2.0%,烧结温度为950℃。在该条件下制备的BaTiO₃陶瓷介电常数达到1364,介电损耗低至1.2%。     

Composition dependence of the photophysical and photocatalytic properties of (AgNbO3)1−x(NaNbO3)x solid solutions

A series of orthorhombic photocatalysts (AgNbO₃)_1−x(NaNbO₃)_x solid solutions have been synthesized by a solid-state reaction method. The composition dependence of the photophysical and photocatalytic properties of synthesized solid solutions has been investigated systematically. With an increase in the content of NaNbO₃, we found that (1) the lattice parameters decreased; (2) the Nb-O bond length in NbO₆ octahedron reduced; (3) the band gap increased; and (4) the mean particle size decreased while the Brunauer-Emmett-Teller (BET) surface area increased. Photocatalytic activities of the (AgNbO₃)_1−x(NaNbO₃)_x (0?x?0.5) samples were evaluated from gaseous 2-propanol (IPA) decomposition into acetone and CO₂ under visible-light irradiation emitted from blue-light-emitting diodes (BLEDs; light intensity: 0.01 mW cm⁻²). Among all the samples, the (AgNbO₃)_0.6(NaNbO₃)_0.4 sample showed the highest photocatalytic activity.