玻碳电极上六氰亚铁酸钯膜的现场FTIR光谱电化学研究

本文报道六氰亚铁酸钯膜修饰电极在ＨＣｌ,ＫＣｌ和ＮａＣｌ溶液中的现场反射ＦＴＩＲ光谱电化学研究,结果表明该修饰膜具有内外两层结构,分别为Ｐｄ２Ｆｅ（ＣＮ）６和Ｍ２ＰｄＦｅ（ＣＮ）６,其中Ｍ为支持电解质一价阳离子．在１ｍｏｌ／ＬＮａＣｌ中,内层的氧化电位Ｅｍ＝０．８７Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）,外层为０．７７Ｖ．在１ｍｏｌ／ＬＨＣｌ或ＫＣｌ中两层的氧化还原波重叠为一个大ＣＶ波峰而难以分辨,然而现场ＦＴＩＲ光谱电化学清晰地分辨出这两种结构在所有３种溶液中ＣＮ的不同振动频率,发现Ｈ＋离子是最佳的支持电解质,能使这两种结构同时发生氧化反应     

痕量亚硝酸根的聚氯乙烯液态膜四氯络铁(Ⅲ)离子电极测定

以新型阴离子载体Ｓ－烷基双硫腙,制备了ＦｅＣｌ＾－４阴离子选择性电极,研究了电极的性能,确定了亚硝酸催化氧化Ｆｅ＾２＋的最佳反应条件,在４ｍｏｌ／Ｌ ＮａＣｌ－０．２ｍｏｌ／Ｌ ＨＣｌ介质中反应５０ｍｉｎ时以尿素终止,反应生成的Ｆｅ（Ⅲ）以ＦｅＣｌ＾－４选择电极电位法测定。间接测定ＮＯ＾－２。线性范围为１５－３５０μｇ／ＬＮＯ＾－２,检出限为８μｇ／Ｌ。该法应用于雪水和水样中亚硝酸根的测定,结果与光度法一致。     

阳极溶出伏安法测定痕量汞的研究

痕量汞的测定方法有很多[1 ] 。原子吸收法虽然具有较高的灵敏性 ,但是仪器设备昂贵 ,分析步骤较繁琐。近年来 ,化学修饰电极阳极溶出伏安法在对汞痕量分析方面的研究报道也不少[2～3] ,测定的检测限一般在 1 0 - 6～ 1 0 - 9ｇ·ｍｌ- 1 ,但它容易产生记忆效应 ,洗脱不良。本文以玻碳电极为工作电极 ,在ＨＣｌ ＮａＣｌ Ｃｄ2 +中 ,示差脉冲阳极溶出伏安法 (ＤＰＳ)测定痕量汞 ,汞的平均回收率达80 %。1　实验部分1 1　主要仪器与试剂ＰＡＲ— 384极谱仪 (美国 ) ;三电极系统 :工作电极为玻碳电极 ,参比电极为Ａｇ/ＡｇＣｌ电极 ,对电极为…     

药物分子在玻碳电极电的电分析化学研究：Ⅳ.乙酰螺旋霉素的伏安测定

本文对乙酰螺旋霉素在ＧＣＥ上的伏安行为进行了研究，发现在磷酸盐缓冲溶液（ｐＨ＝７．７８）中，於＋０．８５Ｖ（ｖｓ，Ａｇ／ＡｇＣｌ）左右产生一良好的阳极氧化伏安峰，浓度在０．５～１００μｇ／ｍＬ之间与峰电流呈线性关系，分析了制剂中乙酰螺旋霉素的含量，相对标准偏差为４．５％，平均回收率为１０１％，经循环伏安法验证，电极反应为不可逆反应。     

药物分子在玻碳电极上的电分析化学研究：Ⅲ.柱晶白霉素的伏安测定

本文对柱晶白霉素在ＧＣＥ上的伏安行为进行了研究，发现在磷酸盐缓冲溶液（ｐＨ７．１３）于＋０．９３Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）左右产生一清晰伏安氧化峰可用于定量，分析了制剂中柱晶白霉素的含量，得到满意的结果，经循环伏安法验证，柱晶白霉素在ＧＣＥ上的电极反应不可逆反应。     

羟乙芦丁在玻碳电极上的阳极微分脉冲伏安法测定

本文对羟乙芦丁在玻碳电极上的阳极微分脉冲安行为进行了研究，发现在Ｎａ２ＨＰＯ４溶液中（ｐＨ＝８．９５）于＋０．６４Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）左右产生一个良好的阳极氧化伏安峰，浓度在５～６０ｍｇ／Ｌ之间与峰电流呈线性关系，不需分离直接测定了片剂中的羟乙芦丁含量。电极反应为扩散速率控制的不可逆可程。     

聚乙烯醇存在下以硝酸铁代替铁铵矾用Volhard法测定银和氯离子

１引言Ｖｏｌｈａｒｄ法以铁铵矾作指示剂，终点不够敏锐。尤其是直接滴定Ａｇ＋时，ＡｇＳＣＮ沉淀易吸附Ａｇ＋而导致终点提前；返滴定Ｃｌ－时ＡｇＣｌ沉淀易转化为ＡｇＳＣＮ，使终点颜色闪而褪去难于观察，分析结果偏低。虽用有机溶剂（如硝基苯）可促进ＡｇＣｌ沉淀凝聚与溶剂化而减缓ＡｇＣｌ的转化，但有机溶剂多数有毒使测定条件恶化．作者提出以聚乙烯醇（ＰＶＡ）化学修饰ＡｇＳＣＮ、ＡｇＣｌ沉淀的结构，阻止ＡｇＳＣＮ对Ａｇ＋的吸附与ＡｇＣｌ的转化，用硝酸铁代替铁铵矾指示滴定终点测定Ａｇ＋、Ｃｌ－的方法。本法比经典Ｖ…     

槲皮素在玻碳电极上的伏安行为研究

1　引　　言槲皮素 (ｑｕｅｒｃｅｔｉｎ ,ＱＵＥ)是许多天然中草药的主要成分 ,如银杏叶、高良姜、鱼腥草、柴胡等都含有ＱＵＥ。测定ＱＵＥ的方法有一阶导数分光光度法、示差脉冲极谱法、ＨＰＬＣ法以及荧光光度法等。莫金垣等以聚酰胺修饰碳糊电极对ＱＵＥ的伏安性能进行了研究。本文研究了ＱＵＥ在玻碳电极 (ＧＣＥ)上的伏安行为 ,并测定了芦丁水解产物中ＱＵＥ的含量。2　实验部分2 .1　仪器和试剂　ＬＫ98微机电化学分析系统 (天津兰力科公司 ) ;ＧＣＥ为工作电极 ,Ａｇ/ＡｇＣｌ电极为参比电极 ,Ｐｔ丝为对电极。 1.0 0× 10 - 3ｍｏ…     

罂粟碱的吸附伏安行为的研究

在ＮＨ３－ＮＨ４Ｃｌ底液中，罂粟碱在汞电极上有一一线性扫描还原峰，峰电位Ｅｐｃ＝－１．４４（ｖｓ．ｓａｔ．Ａｇ／ＡｇＣｌ）。该峰具有明显的吸附性。当ＰＡＰ浓度较小时，扫速较快，搅拌富集时间较长时，电极反应完全为吸附态的ＰＡＰ的还原所控制。     

药物分子在玻碳电极上的电分析化学研究

提出了一种测定安乃近新法。由于安乃近没有电活性，故将安乃近和盐酸在１００℃共热后生成电活性产物，用玻碳电极在０．１ｍｏｌ／Ｌ ＮａＯＨ中得一良好和阳极氧化伏安峰，Ｅｐ＋０．３５Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）左右，峰电流与安乃近浓度在０．１－１００ｍｇ／Ｌ之间呈线性关系，分析了制剂安乃近的含量，实验证实电极反应属于扩散控制的不可逆过程。     

Studies of the chlorpheniramine solid-state ion-selective electrode

An Ag/AgCl solid-state electrode was prepared by using urea-formaldehyde resin as the frame material and KCl powder as the active material. Using the prepared Ag/AgCl solid-state electrode as substrate and chlorpheniramine tetraphenylborate ion-pair complex as the active component, a new type of solid-state chlorpheniramine ion-selective electrode was constructed. The properties of the electrode were studied in detail. The electrode shows a rather good stability and can be used in the potentiometric determination of chlorpheniramine.     

银掺杂聚L-酪氨酸修饰电极同时测定多巴胺、肾上腺素和抗坏血酸

用循环伏安法制备银掺杂聚L-酪氨酸修饰玻碳电极,研究了多巴胺、肾上腺素和抗坏血酸在其电极上的电化学行为,建立了同时测定多巴胺、肾上腺素和抗坏血酸的新方法。当3种组分共存时,在磷酸盐缓冲溶液(pH6.0)中,扫描速率为140mV/s,多巴胺和肾上腺素在修饰电极上分别产生还原峰,峰电位分别为0.198和-0.205V,多巴胺和肾上腺素氧化峰重叠,峰电位为0.313V(vs.Ag/AgCl);抗坏血酸产生一个氧化峰,峰电位0.108V(vs.Ag/AgCl)。多巴胺和肾上腺素的ΔEpc=0.403V,抗坏血酸的氧化峰与多巴胺和肾上腺素的ΔEpa=0.205V,用还原峰和氧化峰可同时测定多巴胺、肾上腺素和抗坏血酸,3种组分同时测定的线性范围分别为5.0×10-6～1.0×10-4mol/L,8.0×10-6～1.0×10-4mol/L和3.0×10-5～1.0×10-3mol/L;检出限分别为5.0×10-7,8.0×10-7和5.0×10-6mol/L。本方法用于人尿液中多巴胺、肾上腺素和抗坏血酸的同时测定,结果满意。     

The fabrication and performance of an Ag/AgCl reference electrode in human serum

A simple set of electric circuits was used to assemble a pulse generator. With pulse potentials and under galvanostatical control, a clean silver wire was anodized electrochemically for 0.2–0.5 min in 1.0 mol l⁻¹ HCl with a pulse current density of 20 mA cm⁻², and the pulse wave parameters of t_a/t_c = 1 and a cycle of 4 s forming an Ag/AgCl reference electrode. Even though the AgCl layer was consumed during the working period when the Ag/AgCl electrode was used as a cathode, the AgCl layer could be in situ recovered electrochemically in serum used when a reversed potential was applied to the electrode system immediately after the measuring program was finished. The current response curve of the anode indicated that an AgCl layer in high density was basically accomplished during the first 6 pulse cycles in human serum. In order to keep a stable and uniform AgCl layer on the reference electrode after each measuring cycle, the ratio of the recovery time (t_r) to the working time (t_w) was measured and the smallest value was obtained at 0.03. The open-circuit potential of the Ag/AgCl electrode with respect to a SCE in 0.1 mol l⁻¹ KCl was monitored over a period of 14 days and the mean value was 40.09 mV vs SCE with a standard deviation of 2.55 mV. The potential of the Ag/AgCl reference electrode did remain constant when the measurements were repeated more than 600 times in undiluted human serum with a standard deviation of 1.89 mV. This study indicated that the Ag/AgCl reference electrode could been rapidly fabricated with a pulse potential and could be used as a reference electrode with long-term stable properties in human serum samples.     

A wall-jet disc electrode for simultaneous and continuous on-line measurement of sodium dithionite, sulfite and indigo concentrations by means of multistep chronoamperometry

In this paper, a multistep chronoamperometric method is presented to measure continuously and simultaneously the concentrations of indigo, sodium dithionite and sulfite for application in textile dyeing processes. The method is based on the oxidation of sodium dithionite and the reduced form of indigo at a platinum disc electrode. Sodium dithionite is oxidized at a potential of 0.3 V versus Ag/AgCl and shows transport controlled steady state currents at a rotating disc electrode and a wall-jet electrode. The latter has been developed for the purpose of the application. Implementation of a wall-jet instead of a rotating disc electrode is much easier and cost-effective. Indigo is oxidized at −0.55 V versus Ag/AgCl to a virtually water insoluble product, which precipitates at the electrode surface. Indigo behaves quasi-reversibly, and is reduced at a potential of −0.9 V versus Ag/AgCl. In order to clean the electrode surface this reduction is used as a step in the multistep sequence. Finally, sulfite is oxidized at a potential of 0.8 V versus Ag/AgCl but did not give rise to well defined transport controlled limiting currents. However, determination of its concentration is still possible within error margins of 5%.     

Disposable Anodic Stripping Voltammetric Sensor for Heavy Metal Analysis in Environmental Samples

A disposable sensor was developed for anodic stripping voltammetric analysis of heavy metals utilizing the HgO-modified composite electrode technique. It was prepared by integrating a HgO-modified electrode, Ag/AgCl reference electrode and carbon counter electrode on a polycarbonate strip by screen printing technique.     

Electrochemical preparation of effective and low cost catalyst for electrooxidation of ethanol

A nanocatalyst coating was prepared at surface of a glassy carbon electrode by electropolymerization of pyrrole by cycling the electrode potential between ?0.8 and 0.8 V (vs. Ag/AgCl). Then, polypyrrole film was potentiostatically coated with platinum nanoparticles at constant potential of ?0.2 V (vs. Ag/AgCl). The resulting electrode was denoted as GCE/PPy/Pt. This modified electrode was characterized by IR, SEM, TEM and EDX. The electrocatalytic oxidation of ethanol at the GCE/PPy/Pt has been investigated using cyclic voltammetric and chronoamperometric methods. The effects of various parameters on electrocatalytic oxidation of the ethanol, such as the thickness of PPy film, the amount of platinum nanoparticles, ethanol concentration, potential scan rate and working potential limit in anodic direction, were investigated. The kinetic of the ethanol oxidation is discussed on the GCE/PPy/Pt. The stability and reproducibility of this modified electrode were also studied.     

Study of an Au colloid self-assembled electrode and its application to the determination of carbon monoxide

A novel electrochemical sensor has been developed for the detection of carbon monoxide. The chemically modified electrode, prepared by reaction of cysteine and then an Au colloid of size approximately 15 nm with a platinum microelectrode, has excellent catalytic activity toward carbon monoxide, with an oxidation potential of +600 mV relative to the Ag/AgCl electrode. The CO gas sensor is based on an Au colloid self-assembled modified electrode as working electrode, an Ag/AgCl electrode as reference electrode, a Pt electrode as counter electrode, and a porous film which is in direct contact with the gas-containing atmosphere. The effects on the determination of CO of different internal electrolyte solutions of perchloric acid, hydrochloric acid, sulfuric acid, nitric acid, and phosphate buffer of different concentrations were also studied. The sensor is characterized by a short response time and highly reproducible detection of CO. This sensor can be used in the field of environmental monitoring and control.     

Study of an Au colloid self-assembled electrode and its application to the determination of carbon monoxide

A novel electrochemical sensor has been developed for the detection of carbon monoxide. The chemically modified electrode, prepared by reaction of cysteine and then an Au colloid of size approximately 15 nm with a platinum microelectrode, has excellent catalytic activity toward carbon monoxide, with an oxidation potential of +600 mV relative to the Ag/AgCl electrode. The CO gas sensor is based on an Au colloid self-assembled modified electrode as working electrode, an Ag/AgCl electrode as reference electrode, a Pt electrode as counter electrode, and a porous film which is in direct contact with the gas-containing atmosphere. The effects on the determination of CO of different internal electrolyte solutions of perchloric acid, hydrochloric acid, sulfuric acid, nitric acid, and phosphate buffer of different concentrations were also studied. The sensor is characterized by a short response time and highly reproducible detection of CO. This sensor can be used in the field of environmental monitoring and control.     

Electrochemical oxidation of aniline in a silica sol–gel matrix

Electrochemical oxidation of aniline encapsulated in a silica solid electrolyte prepared by a sol–gel process yielded products that were dependent on the pore size. An acid-catalyzed process that used tetramethyl orthosilicate as the precursor and aniline as a dopant yielded the silica. When the aging time was limited to one day so that a mesoporous solid was obtained, the potentiodynamic oxidation of aniline at a carbon fiber electrode resulted in the formation of polyaniline. With aging times of 3–5 days, microporous silica was obtained. In this electrolyte, the formation of dimers and other oligomers was observed by cyclic voltammetry. Evidence for these products was the presence of a quasi-reversible redox couple at 0.2 V vs Ag/AgCl that was previously related to oligomeric aniline by Raman spectroscopy. The results supported the hypothesis that the pore structure of sol–gel electrolytes can influence the pathways of electrode reactions therein.     

无液接裸露式Ag/AgCl参比电极的研制及应用

提出了一种无液接裸露式Ag/AgC l参比电极制备方法,测试了该参比电极的稳定性、重现性、可逆性、响应时间、温度影响等因素。实验结果表明,该电极电位稳定在49 mV,响应时间在30 s以内时,具有重现性、可逆性好,使用寿命长,温度影响小等特点,可替代饱和甘汞和Ag/AgC l参比电极。