分散固相萃取气相色谱-负化学离子源质谱法测定大豆和玉米中20种农药的残留量

建立了一种大豆和玉米中20种农药残留量的分散固相萃取气相色谱-负化学离子源质谱分析方法。样品经乙腈提取并浓缩后加入N-丙基乙二胺（PSA）、石墨化碳黑和C18 3种填料进行分散固相萃取净化,气相色谱-负化学离子源质谱分时段选择离子监测技术测定与确证,外标法定量。所有农药在20～400 μg/L范围内线性均良好;方法的定量限(LOQ)均不高于2 μg/kg;在5,10和20 μg/kg 3个添加水平下所有农药的平均回收率均处于70%～130%之间,相对标准偏差(RSD)低于17%;运用该方法检测大豆和玉米样品时没有干扰现象。     

气相色谱-负化学离子源质谱测定大豆和玉米中12种三唑类杀菌剂的残留量

建立了一种可用于大豆和玉米中12种三唑类杀菌剂残留量测定的分散固相萃取-气相色谱-负化学离子源质谱方法。样品经含1%冰醋酸的乙腈提取,分散固相萃取法净化,采用气相色谱-负化学离子源质谱分时段选择离子监测技术进行测定与确证,外标法定量。12种农药在50～1000 μg/L范围内线性关系均良好;所有农药的方法定量限(LOQ)均低于8 μg/kg;在10,20和40 μg/kg 3个添加水平下所有农药的回收率为70%～130%,相对标准偏差(RSD)≤13.9%。该方法在检测大豆和玉米基质时无干扰现象出现。     

气相色谱-负化学源质谱联用法测定水产品及食用油中氟乐灵的残留量

建立了一种可用于水产品及食用油中氟乐灵残留量分析的分散型固相萃取-气相色谱-负化学离子源质谱方法。水产品及食用油经乙腈提取,4 ℃冷藏后,采用分散型固相萃取法净化,由气相色谱-负化学离子源质谱选择离子监测技术进行测定与确证,同位素内标法定量。在1~40 μg/L范围内氟乐灵农药的线性关系良好;方法定量限（LOQ）为0.02 μg/kg;对鳗鱼、烤鳗、梭子蟹、小龙虾、猪油和橄榄油等6种复杂基质进行1.0、2.0和3.0 μg/kg等3个水平的添加回收试验,平均回收率均处于80%~100%之间,RSD≤10.3%;无干扰现象出现。该方法可作为水产品及食用油中氟乐灵残留检测的确证方法。     

气相色谱-负化学源质谱联用法测定菊酯类农药

通过固相萃取-气相色谱-负化学离子源质谱技术建立了11种拟除虫菊酯类农药残留的检测方法,并应用于茶叶农残检测.样品经乙酸乙酯提取后,用串联的活性炭和中性氧化铝固相萃取柱选择性地富集茶叶中待测组分,再由气相色谱-负化学离子源质谱分时段选择离子监测技术进行测定.方法简单快速,一次进样就能得到11种菊酯残留结果;准确度和精密度高,在0.016 μg/kg、0.032 μg/kg和0.064 μg/kg 3个添加水平下的回收率在70%～110%之间,CV≤7.4%;选择性好,消除了色素和其它杂质干扰;灵敏度高,检出限低,除了氯菊酯为10 μg/kg外,其它菊酯检出限都在μg/kg级,七氟菊酯则达到了0.02 μg/kg.     

蔬菜中26种农药残留的高效液相色谱-串联质谱法测定

建立了蔬菜中26种农药的反相高效液相色谱-电喷雾串联质谱 (LC-ESI MS/MS) 检测方法.蔬菜样品经含0.1%醋酸的乙腈提取、浓缩、分散型固相萃取净化,液相色谱串联质谱测定,内标法定量.26种农药在5.0 ～200 μg/L范围内线性关系良好(r2＞0.997).在豌豆、菠菜、脱水葱3种基质中的检出限和定量下限均为2.0 μg/kg和5.0 μg/kg.在5.0、10.0、40.0 μg/kg 3个添加水平下,26种农药的回收率为70% ～110%,精密度(RSD)小于15%.方法准确、灵敏、简单,适用于蔬菜中26种农药残留的同时测定.     

气相色谱-负化学源质谱法测定蔬菜中17种拟除虫菊酯类农药残留量

建立了气相色谱-负化学源质谱检测蔬菜中17种拟除虫菊酯类农药残留量的方法。样品中的目标物经乙腈提取后,用乙二胺-N-丙基甲硅烷(PSA)和石墨化炭黑填料进行分散固相萃取净化,气相色谱-负化学源质谱选择离子监测模式测定,同位素内标法定量。在甜豌豆、绿花菜和大葱基质中均未见干扰所有农药测定的现象。17种拟除虫菊酯类农药的定量限均为0.02～5 μg/kg。在10、20、30和100 μg/kg等4个添加水平下,所有农药的回收率均为71.0%～139.0%,相对标准偏差≤12.8%。该方法可作为蔬菜中17种菊酯类农残检测的确证方法。     

分散固相萃取净化液相色谱-质谱联用快速检测糙米中的多种残留农药

建立了同时检测糙米中多种农药残留的分析方法.采用乙腈提取,使用N-丙基乙二胺键合固相吸附材料(PSA)和C18硅胶胶联吸附剂分散固相萃取(dispersive-SPE)净化,高效液相色谱-电喷雾串联质谱,正离子模式检测,内标法定量.30种农药在0.05～2mg/kg范围内线性良好,方法检出限和定量限分别为0.5～20 μg/kg和2～60 μg/kg,30种农药平均回收率在73%～109%之间,相对标准偏差<10%,均能够满足农药残留分析的要求.     

固相萃取-气相色谱/负化学电离-质谱法测定酸水解植物蛋白及酱油中的3-氯-1,2-丙二醇

建立了酸水解植物蛋白及酱油中3-氯-1,2-丙二醇(3-MCPD)的固相萃取-气相色谱/质谱测定方法。样品经Aoisa-HBL固相萃取柱萃取,正己烷-乙酸乙酯净化提取,七氟丁酰咪唑衍生,衍生物经气相色谱/负化学电离-质谱（GC/NCI-MS）选择离子模式(SIM)检测,外标法定量。3-MCPD的定量检测限为0.5 μg/kg,平均回收率为92.2%～97.4%,相对标准偏差为3.6%～10.9%。该方法检测灵敏度高,定性定量准确。     

程序升温大体积进样气相色谱-负化学离子源质谱法测定白菜和苹果中103种农药残留

采用程序升温大体积进样(PTV-LVI)和负化学离子源(NCI)技术建立了白菜和苹果中103种农药残留分析的气相色谱-质谱检测方法。PTV-LVI参数优化为: 初始温度45 ℃、分流排空流量20 mL/min、吹扫时间1 min和溶剂挥发温度60 ℃。样品采用QuEChERS方法进行快速处理,在NCI方式下进样10 μL,用基质标准溶液进行定量,结果表明103种农药的方法检出限均低于5 μg/kg。在5 μg/kg和10 μg/kg添加水平下,白菜和苹果中农药的平均回收率为58.5%～113.2%,相对标准偏差为3.3%～14.5%。该方法样品处理简单快速,相比普通分流/不分流进样和电子轰击电离气相色谱-质谱法,其灵敏度和选择性明显提高,适用于日常检测工作。     

分散固相萃取-气相色谱-串联质谱法测定蔬菜中107种农药的残留量

采用分散固相萃取-气相色谱-串联质谱(QuEChERS-GC-MS/MS)建立了蔬菜中107种农药残留量的分析方法。样品由含1%冰醋酸的正己烷饱和乙腈提取、分散固相萃取法净化,采用气相色谱-串联质谱方法在分时段选择反应监测模式下进行测定,外标法定量。所有农药在0.05～1 mg/L范围内线性关系均良好;所有农药的方法定量限(LOQ)均低于10 μg/kg;在10 μg/kg的添加水平下,大蒜、青刀豆、萝卜和菠菜4种基质中绝大多数农药的平均回收率处于60%～130%之间,相对标准偏差(RSD)不大于15.3%。该方法不仅能用于多种蔬菜基质中107种农药残留的检测,而且还能较好地解决本底成分相当复杂的大蒜基质极易出现的干扰问题。     

Mixtures formed of alkyl acetates with olive oil at 298.15 k

Enthalpies of mixing and heat capacities of the systems formed of alkyl acetates (ethyl acetate, propyl acetate, isopropyl acetate, butyl acetate and isobutyl acetate) with olive oil were measured at 298.15 K. The mixing of acetates with the oil was strongly endothermic, and the highest measured enthalpies per mole of mixture were 2000 J mol^-1 for ethyl acetate at an acetate mole fraction of 0.6. The heat capacities of the mixtures were calculated too and values were decreasing as the mole fraction of acetate increases and varied from 296 to 3929 J K^-1 mol^-1. This revised version was published online in July 2006 with corrections to the Cover Date.     

碳酸二甲酯法合成1,5-萘二氨基甲酸甲酯的反应机理

 应用红外光谱技术研究了在乙酸锌催化作用下1,5-萘二胺与碳酸二甲酯甲氧基羰基化反应机理. 结果表明,二水合乙酸锌只有失去两个结晶水变成无水乙酸锌后才能产生催化活性. 无水乙酸锌与1,5-萘二胺形成一个新的配位络合物,该配位络合物是一个适宜的亲核试剂,能与碳酸二甲酯进行亲核反应,生成1,5-萘二胺的甲氧基羰基化产物. 在无水乙酸锌与1,5-萘二胺形成配位络合物的过程中,无水乙酸锌的结构从双齿型转变成单齿型.     

碳酸二甲酯法合成1，5-二氨基甲酸甲酯的反应机理

应用红外光谱技术研究了在乙酸锌催化作用下1，5-萘二胺与碳酸二甲酯甲氧基羰基化反应机理．结果表明，二水合乙酸锌只有失去两个结晶水变成无水乙酸锌后才能产生催化活性．无水乙酸锌与1，5-萘二胺形成一个新的配位络合物，该配位络合物是一个适宜的亲核试剂，能与碳酸二甲酯进行亲核反应，生成1，5-萘二胺的甲氧基羰基化产物．在无水乙酸锌与1，5-萘二胺形成配位络合物的过程中，无水乙酸锌的结构从双齿型转变成单齿型．     

Radical reactions involving esters of fumaric acid—III. Chain transfer processes

Model compounds have been used in studies at 60° in connection with transfer to polymer during the copolymerization of vinyl acetate with esters of fumaric acid. Succinate esters were used to simulate the fumarate ester units and ethyl acetate the vinyl acetate units in the copolymers. The succinate esters are much more reactive than ethyl acetate in transfer reactions with polyvinyl acetate radicals. Methyl isobutyrate and methyl propionate were also examined to assess the difference in reactivity in transfer of tertiary and secondary hydrogen atoms. It is concluded that branching is a very important reaction in the preparation of high conversion copolymers of fumarate esters with vinyl acetate.     

Regularities of adsorption of zinc acetate from aqueous solutions onto the surface of modified activated carbons

The dependence of the characteristics of Zn(OAc)₂/C catalysts for vinyl acetate synthesis on the solution circulation rate, on the temperature and initial concentration of zinc acetate solution, and on the procedures for modification of activated carbons with oxidants was studied with the aim to achieve uniform distribution of the supported active component (zinc acetate). Oxidation of activated carbons with hydrogen peroxide and nitric acid increases the adsorption rate and the amount of adsorbed zinc acetate. Treatment of the support with acetic acid leads to an increase in the adsorption capacity for zinc acetate, to more uniform distribution of the active component over the surface, and to enhancement of the catalyst activity. The hydrodynamic regime of stirring in the two-phase system consisting of the support and zinc acetate solution is an important factor determining the activity and stability of the zinc acetate catalyst for vinyl acetate synthesis.     

Secondary tritium isotope effects,a useful mechanistic probe for the study of acetoxyl participation and transfer

Tritium labelling on the acetoxyl methyl group has been used to probe the mode of incorporation of acetate into cinnamyl acetate in the solvolyes of cinnamyl chloride and cinnamylmercuric acetate, and in the allylic oxidation of allylbenzene with mercuric acetate.     

Sum-frequency generation of acetate adsorption on Au and Pt surfaces: molecular structure effects

The reversible adsorption of acetate on polycrystalline Au and Pt surfaces was investigated with broadband sum-frequency generation (SFG) and cyclic voltammetry. Specifically adsorbed acetate as well as coadsorbed sulfuric acid anions are observed for the first time with SFG and give rise to dramatically different SFG intensities on Au and Pt surfaces. While similar coverages of acetate adlayers on Au and Pt surfaces are well established by previous studies, an identification of the interfacial molecular structure has been elusive. However, we have applied the high sensitivity of SFG for interfacial polar ordering to identify different acetate structures at Au and Pt surfaces in contact with HClO(4) and H(2)SO(4) electrolytes. Acetate competes with the formation of surface oxides and shifts the oxidation threshold of both Au and Pt electrodes anodically. Effects of the supporting electrolyte on the formation of acetate adlayers are revealed by comparing SFG spectra in HClO(4) and H(2)SO(4) solutions: Sulfuric acid anions modify the potential-dependent acetate adsorption, compete with adsorbed acetate on Au and coadsorb with acetate on Pt surfaces.     

N-Methyl indoxyl Esters as Substrates for Cholinesterase

Abstract

Several esters were prepared as substrates for cholinesterase: the acetate, propionate and butyrate esters of N-methyl indoxyl, umbelliferone acetate, and the acetate and butyrate esters of 4-methyl umbelliferone. Comparison of these substrates with other fluorogenic esters: indoxyl acetate, indoxyl butyrate, resorufin acetate, B-carbonaphthoxycholine, and β-naphthyl acetate indicated that N-methyl indoxyl butyrate was the best substrate for pseudo cholinesterase. Analysis of as little as 5 × 10^?6 units per ml. of cholinesterase can be performed by a direct initial reaction-rate method in 2–3 minutes with an accuracy and precision of about 1.5%.     

Adaptation of glycolysis and growth to acetate in Sporolactobacillus sp. Y2-8

Exogenous addition of a low concentration of acetate (2 g/L sodium acetate) effectively decreased acetic acid excretion and lowered the ATP content in Sporolactobacillus sp. Y2-8 without any growth defect although the acetate could not be utilized at an initial glucose concentration of 150 g/L. This induced an enhanced glycolytic flux with increased specific activities of hexokinase and phosphofructokinase, probably to compensate for the lowered efficiency of ATP production. However, with increasing concentrations (5 g/L sodium acetate), acetate was utilized first before being produced again, causing a growth lag at the transition. Glucose consumption was also reduced at high acetate concentrations, resulting in decreased D-lactic acid production. These results demonstrate that acetate plays a significant role in regulating glycolysis and growth of Sporolactobacillus.     

高取代度魔芋葡甘聚糖醋酸酯的制备及其热塑性和流变性研究

以魔芋葡甘聚糖(KGM)为原料,浓硫酸为催化剂,乙酸酐为改性剂,制备了KGM醋酸酯.研究了反应条件对KGM醋酸酯取代度(DS)的影响,KGM醋酸酯制备的最佳反应条件是乙醇∶水量比5∶5,反应时间2h,反应温度75℃,催化剂浓硫酸的浓度0.1mol/L,KGM与乙酸酐的量比5∶40(g/mL),取代度高达2.93,其分子量与KGM相比,则明显降低.运用傅立叶红外光谱仪(FTIR)、X射线衍射仪(XRD)、扫描电镜(SEM)、热重分析仪(TGA)、示差扫描量热仪(DSC)和旋转流变仪对KGM和高取代度KGM醋酸酯进行了表征.结果表明,KGM醋酸酯的羰基(CO)特征吸收峰较KGM明显增强,其表观形貌大部分为疏松絮状,KGM及其醋酸酯均为非晶态结构.与KGM相比,KGM醋酸酯的热稳定性下降,分解温度(Td)由KGM的261.10℃降低至KGM醋酸酯的204.56℃,KGM醋酸酯出现了明显的玻璃化转变,其玻璃化转变温度(Tg)为128.49℃.KGM醋酸酯是典型的黏弹性材料,其弹性比率占21.27%,其剪切黏度η对温度变化非常敏感,可通过温度的改变来调节KGM醋酸酯的加工流动性.KGM醋酸酯具有较好的热塑性.