Electroless plating of copper on fly ash cenospheres using polyaniline‐Pd activation

The polyaniline of different intrinsic oxidation states, viz., the emeraldine (EM) and the leucoemeraldine (LM) states, were coated on 3‐aminopropyltriethoxy silane modified fly ash cenospheres. Without prior sensitization by SnCl₂ solution, Pd activation by PdCl₂ solution was carried out on EM and LM laden cenospheres, followed by electroless plating of copper (Cu). The topography and composition of the composites were characterized by scanning electron microscopy, X‐ray diffraction, and X‐ray photoelectron spectroscopy, etc. The results indicate that the oxidation state of the LM layer showed a much bigger increase than that of the EM layer in the Pd activation process, while coupled Pd reduction underwent to a more extent on the LM layer. The metallic Pd atoms on the LM and EM layers surface initiated the subsequent electroless plating of Cu, and the coated Cu on LM laden cenospheres had a much more uniform and compact morphology than that on EM laden cenospheres. Copyright © 2012 John Wiley & Sons, Ltd.     

Pd‐Cu alloy nanoparticle supported on amine‐terminated ionic liquid functional 3D graphene and its application on Suzuki cross‐coupling reaction

Well distributed Pd‐Cu bimetallic alloy nanoparticles supported on amine‐terminated ionic liquid functional three‐dimensional graphene (3D IL‐rGO/Pd‐Cu) as an efficient catalyst for Suzuki cross‐coupling reaction has been prepared via a facile synthetic method. The introduction of IL‐NH₂ cations on the surface of graphene sheets can effectively avoid the re‐deposition of graphene sheets, allowing the catalyst to be reused up to 10 cycles. The addition of Cu not only saves cost but also ensures high catalytic efficiency. It is worthy to note that the catalyst 3D IL‐rGO/Pd_2.5Cu_2.5 can efficiently catalyze the Suzuki cross‐coupling reaction with the yield up to 100% in 0.25 h, almost one‐fold higher than that by the pristine IL‐rGO/Pd_2.5 catalyst (52%). The Powder X‐Ray Diffraction (XRD), combining energy dispersive X‐ray spectroscopy (EDS) mapping results confirm the existence and distribution of Pd and Cu in the bimetallic nanoparticles. The transmission electron microscopy (TEM) reveals the nanoparticle size with an average diameter of 3.0 ± 0.5 nm. X‐ray photoelectron spectroscopy (XPS) analysis proved the presence of electron transfer from Cu to Pd upon alloying. Such alloying‐induced electronic modification of Pd‐Cu alloy and 3D ionic liquid functional graphene with large specific surface area both accounted for the catalytic enhancement.     

A Novel Electrochemical Method for the Analysis of Hydrogen Peroxide with the Use of a Glassy Carbon Electrode Modified by a Prussian Blue/Copper‐Gold Bimetallic Nanoparticles Hybrid Film

A novel Prussian blue/copper‐gold bimetallic nanoparticles hybrid film modified electrode was prepared by electrochemical deposition on a glassy carbon electrode (PB/Cu‐AuNPs/GCE). Morphology and electrochemistry of this electrode were studied by UV‐vis spectroscopy, scanning electron microscopy, X‐ray diffraction, cyclic voltammetry and electrochemical impedance spectroscopy. The sensor showed significantly better electrocatalytic activity for the reduction of hydrogen peroxide in comparison with the single PB/GCE and PB/AuNPs/GCE. This was attributed to the synergistic effect of PB and Cu‐Au bimetallic nanoparticles. Also, the sensor demonstrated an overall high level of performance for the analysis of H₂O₂ in the concentration range from 0.002 to 0.84 mM.     

Immersion Deposition of Pt Nanoparticles on Porous Silicon for Methanol Oxidation

Porous silicon (PS) was chosen as the substrate for supporting the Pt particles because of great surface area, good conductivity and stability. Pt nanoparticles have been successfully prepared on the substrate by immersion deposition, which is convenient. The component and morphological properties of the films have been investigated by means of X‐ray diffraction (XRD), energy dispersive X‐ray spectroscopy (EDX) and scanning electron microscopy (SEM), which shows that the Pt particles have small size and big specific surface. Cyclic voltammetry (CV) research showed that the Pt nanoparticles had novel catalytic activity for methanol when the immersion deposition time was past 24 min.     

Fe3O4‐supported Schiff‐base copper (II) complex: A valuable heterogeneous nanocatalyst for one‐pot synthesis of new pyrano[2,3‐b]pyridine‐3‐carboxamide derivatives

A novel Cu (II) Schiff‐base complex immobilized on core‐shell magnetic Fe₃O₄ nanoparticles (Fe₃O₄@SPNC) was successfully designed and synthesized. The structural features of these nanoparticles were studied and confirmed by using various techniques including FT‐IR spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy‐dispersive X‐ray spectroscopy (EDS), vibrating sample magnetometer (VSM), X‐Ray diffraction (XRD), wavelength dispersive X‐ray spectroscopy (WDX), and inductively coupled plasma (ICP). These newly synthesized nanoparticles have been used as efficient heterogeneous catalytic system for one‐pot multicomponent synthesis of new pyrano[2,3‐b]pyridine‐3‐carboxamide derivatives. Notably, the catalyst could be easily separated from the reaction mixture by using an external magnet and reused for several successive reaction runs with no significant loss of activity or copper leaching. The present protocol benefits from a hitherto unreported MNPs‐immobilized Cu (II) Schiff‐base complex as an efficient nanocatalyst for the synthesis of newly reported derivatives of pyrano[2,3‐b]pyridine‐3‐carboxamide from one‐pot multicomponent reactions.     

Electrically conductive acrylonitrile–butadiene rubber elastomers prepared by dopamine‐induced surface functionalization and metallization

A novel method for the preparation of electrical conductive surface silvered acrylonitrile–butadiene rubber (NBR) was developed. Dopamine was spontaneously oxide polymerized and deposited onto the surface of NBR. Electroless plating of silver was carried out on the poly(dopamine) (PDA)‐functionalized NBR surface. The composition of the NBR surface was studied by X‐ray photoelectron spectroscopy (XPS). XPS results showed that PDA was successfully deposited onto the NBR surface. The morphology of the NBR surface was observed by scanning electron microscopy (SEM). The SEM images showed that PDA had formed a distinctive layer ready for electroless deposition of silver. The catechol/quinone groups on the PDA molecular structure can be used as binding sites for silver ions. The silvered NBR showed high surface conductivity of 1.4 Ω. Copyright © 2011 John Wiley & Sons, Ltd.     

Highly Active Nickel Nanoparticles Supported on TiO2 Nanotube Electrodes for Methanol Electrooxidation

Nickel nanoparticles/TiO₂ nanotubes/Ti electrodes were prepared by galvanic deposition of nickel nanoparticles on the TiO₂ nanotubes layer on titanium substrates. Titanium oxide nanotubes were fabricated by anodizing titanium foil in a DMSO fluoride‐containing electrolyte. The morphology and surface characteristics of titanium dioxide nanotubes and Ni/TiO₂/Ti electrodes were investigated using scanning electron microscopy and energy‐dispersive X‐ray spectroscopy, respectively. The results indicated that nickel nanoparticles were homogeneously deposited on the surface of TiO₂ nanotubes. The electrocatalytic behaviour of nickel nanoparticles/TiO₂/Ti electrodes for the methanol electrooxidation was studied by electrochemical impedance spectroscopy, cyclic voltammetry, differential pulse voltammetry and chronoamperometry methods. The results showed that Ni/TiO₂/Ti electrodes exhibit a considerably higher electrocatalytic activity toward the oxidation of methanol.     

铝表面前处理及化学沉积镍初期行为

利用开路电位-时间(EOCP-t)曲线,研究铝表面经浸镍和化学预镀镍前处理后,化学沉积镍的初期行为;通过扫描电子显微镜(SEM)观察铝表面经前处理后的表面形貌.结果表明:未经及经前处理的铝表面,化学沉积镍的初期行为都经历去氧化膜、活化、混合控制以及化学沉积过程.经过浸镍和化学预镀镍前处理后的铝表面附着细小的镍颗粒.依据EOCP-t和SEM的最佳实验结果,在含有络合剂和还原剂的碱性预镀镍溶液中,经二次化学预镀镍前处理,成功实现铝基底弱酸性化学镀镍.所获得的化学镀镍层与铝基底结合牢固,呈团颗粒状形貌和非晶态结构.     

Electropolymerization of DBSA‐doped polypyrrole films on PTFE via an electroless copper interlayer

We report on the electroless deposition of thin films of copper on poly(tetrafluoroethylene) (PTFE) and their use as substrates for electropolymerization of polypyrrole. Argon plasma‐treated PTFE films were modified by silanization using N‐[3(trimethoxysilyl)propyl]diethylenetriamine (TMS). The TMS‐modified PTFE films were subsequently activated by PdCl₂ for the electroless deposition of copper. The omission of the commonly used SnCl₂ sensitization step represents a significant process enhancement with environmental and cost benefits. The surface composition of the substrate (before and after surface treatments) and overlayer films was studied using high‐resolution x‐ray photoelectron spectroscopy. A combination of time‐of‐flight secondary ion mass spectrometry and water contact‐angle measurements was also used to study the PTFE surface after argon plasma treatment. The Cu/PTFE films were used as substrates for subsequent pyrrole electropolymerization in aqueous dodecylbenzene sulphonic acid (DBSA) solution. The DBSA‐doped polypyrrole overlayers were successfully deposited on the Cu/PTFE surface using a constant applied potential of 1.5 V. The resulting material exhibited a doping level of 39%, determined using chemical component analysis of the N 1s photoelectron peak. Copyright © 2003 John Wiley & Sons, Ltd.     

Metal Chelate Monomers Based on Nickel Maleate and Chelating N‐Heterocycles as Precursors of Core‐shell Nanomaterials with Advanced Tribological Properties

In this study, new metal chelate monomers based on nickel(II) maleate and chelating N‐heterocycles (2,2′‐bipyridine and 1,10‐phenanthroline) were synthesized and characterized. A detailed analysis of the main stages and features of the kinetics of thermal transformations of metal chelate monomers was carried out. Core‐shell nanomaterials containing nanoparticles of nickel oxide and metallic nickel in a stabilizing nitrogen‐containing polymer matrix were obtained by thermolysis of these monomers. The composition, properties and structure of the nanomaterials were studied using IR spectroscopy, thermal analysis, X‐ray diffraction, atomic force microscopy, scanning electron microscopy, high‐resolution transmission electron microscopy, and energy dispersive X‐ray spectroscopy. The tribological characteristics of NiO nanoparticles as lubricant additives were studied using a pin‐on‐disc tribometer. The coefficient of friction (COF) is the lowest at the optimum concentration of nanoparticles and increasing the concentration above the optimum level leads to an increase in COF.     

Extraction of phenolic compounds from water samples by dispersive micro‐solid‐phase extraction

In this article, the use of magnetically separable sorbent polyaniline/silica‐coated nickel nanoparticles is evaluated under a dispersive micro‐solid‐phase extraction approach for the extraction of phenolic compounds from water samples. The sorbent was prepared by in situ chemical polymerization of aniline on the surface of silica‐modified nickel nanoparticles and was characterized by Fourier transform infrared spectroscopy, transmission electron microscopy, X‐ray powder diffraction, scanning electron microscopy, energy‐dispersive X‐ray spectrometry, and vibrating sample magnetometry. Effective variables such as amount of sorbent (milligrams), pH and ionic strength of sample solution, volume of eluent solvent (microliters), vortex, and ultrasonic times (minutes) were investigated by fractional factorial design. The significant variables optimized by a Box–Behnken design were combined by a desirability function. Under the optimized conditions, the calibration graphs of analytes were linear in a concentration range of 0.02–100 μg/mL, and with correlation coefficients more than 0.999. The limits of detection and quantification were in the ranges of 10–23 and 33–77 μg/L, respectively. This procedure was successfully employed in the determination of target analytes in spiked water samples; the relative mean recoveries ranged from 96 to 105%.     

A green biosynthesis of NiO nanoparticles using aqueous extract of Tamarix serotina and their characterization and application

Nickel oxide nanoparticles were prepared using nickel nitrate as precursor with extract of Tamarix serotina flowers and were characterized using powder X‐ray diffraction, infrared and UV spectroscopies, transmission electron microscopy, vibrating sample magnetometry and BET surface area measurements. Also, the nickel oxide nanoparticles were used as a green and recyclable nanocatalyst for the synthesis of quinoline derivatives. The products are obtained in good to high yields (60–90%) from a one‐pot reaction of 2‐aminobenzophenone and various carbonyl compounds. Copyright © 2016 John Wiley & Sons, Ltd.     

Spinel copper ferrite nanoparticles: Preparation,characterization and catalytic activity

The magnetic CuFe₂O₄ nanoparticles have been synthesized and characterized by various spectroscopic methods, including X‐ray diffraction (XRD), O K, Cu and Fe K ‐edge X‐ray absorption near edge structure (XANES), energy dispersive X‐ray analysis (EDX), scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The azide‐alkyne cycloaddition by the reaction of various phenylacetylenes with a mixture of benzyl halides and NaN₃ and also three component (A³) coupling reaction of aldehyde, alkyne and amine catalyzed by CuFe₂O₄ nanoparticles under aerobic conditions led to the formation of the 1,4‐disubstituted‐1,2,3‐triazoles and propargylamines in excellent yields. The catalyst can be recovered by applying an external magnetic field for the subsequent cycloaddition reactions and reused without any tangible loss in catalytic efficiency.     

Palladium immobilized on amidoxime‐functionalized magnetic Fe3O4 nanoparticles: a highly stable and efficient magnetically recoverable nanocatalyst for sonogashira coupling reaction

We describe the synthesis of a novel Fe₃O₄/amidoxime (AO)/Pd nanocatalyst by grafting of AO groups on Fe₃O₄ nanoparticles and subsequent deposition of Pd nanoparticles. Prior to grafting of AO, the 2‐cyanoethyl‐functionalized Fe₃O₄ nanoparticles prepared through combining 2‐cyanoethyltriethoxysilane and Fe₃O₄ were treated with hydroxylamine. The AO‐grafted Fe₃O₄ nanoparticles were then used as a platform for the deposition of Pd nanoparticles. The catalyst was characterized using Fourier transform infrared spectroscopy, X‐ray diffraction, scanning and transmission electron microscopies, vibrating sample magnetometry, wavelength‐ and energy‐dispersive X‐ray spectroscopies and inductively coupled plasma analysis. Fe₃O₄/AO/Pd is novel phosphine‐free recyclable heterogeneous catalyst for Sonogashira reactions. Interestingly, the novel catalyst could be recovered in a facile manner from the reaction mixture by applying an external magnet device and recycled seven times without any significant loss in activity. Copyright © 2015 John Wiley & Sons, Ltd.     

碳纳米管表面的无钯活化化学镀镍研究

本文提出碳纳米管表面无钯活化的化学镀镍方法.碳纳米管经硝酸氧化和碱中和后表面生成羧基,利用羧基吸附镍离子,之后吸附的镍离子被化学还原为镍的纳米微粒并成为化学镀镍的催化活性中心.红外吸收光谱和电子显微镜观察等证实了上述活化过程的机理.实验表明,新的活化方法对碳纳米管表面化学镀是切实可行的,文中同时对化学沉积层的不同形貌进行讨论.     

Planting of bis(1,5‐cyclooctadiene) nickel upon silica to harvest NiO (<5 nm) nanoparticles in a silica matrix

Bis(1,5‐cyclooctadiene) nickel [Ni(COD)₂] was employed as a nickel precursor to prepare nickel oxide nanoparticles upon high‐surface‐area mesoporous silica. Under protection of argon, Ni(COD)₂ was dissolved in tetrahydrofuran (THF) to react with surface silanols of mesoporous silica SBA‐15, which formed a black powder after completion of the surface reaction. Calcination of the powder produced ultrafine NiO inside the mesoporous silica matrix, which was evidenced by X‐ray diffraction, N₂ adsorption–desorption, transmission electron microscopy and thermogravimetric analysis. The thermogravimetric analysis suggests that NiO formation is a result of surface nickel species calcination, whereas structural characterization clearly show that NiO nanoparticles of <5 nm are evenly distributed inside the silica SBA‐15 matrix and mesoporosity is well preserved upon calcinations and NiO formation. The surface reaction between Ni(COD)₂ and surface silanols was found for the first time, and the method used here may be extended conveniently to prepare other metal oxide nanoparticles upon high‐surface‐area supports as well. Copyright © 2005 John Wiley & Sons, Ltd.     

A novel route to in‐situ incorporation of silver nanoparticles into supramolecular hydrogel networks

A novel strategy was developed for the in situ incorporation of silver nanoparticles into the supramolecular hydrogel networks, in which colloidally stable silver hydrosols were firstly prepared in the presence of an amphiphilic block copolymer of poly(oxyethylene)‐poly(oxypropylene)‐poly(oxyethylene) and then mixed with aqueous solution of α‐cyclodextrin. The analyses from rheology, X‐ray diffraction, and scanning electron microscopy confirmed the formation of the supramolecular‐structured hydrogels hybridized with silver nanoparticles. In particular, the colloidal stability of the resultant silver hydrosol and its gelation kinetics in the presence of α‐cyclodextrin as well as the viscoelastic properties of the resultant hybrid hydrogel were investigated under various concentrations of the used block copolymer. It was found that the used block copolymer could act not only as the effective reducing and stabilizing agents for the preparation of the silver hydrosol but also as the effective guest molecule for the supramolecular self‐assembly with α‐cyclodextrin. In addition, the effects of silver nanoparticles on the gelation process and the hydrogel strength were also studied. Such a hybrid hydrogel material could show a good catalytic activity for the reduction of methylene blue dye by sodium borohydride. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 740–749, 2009     

Phosphorus‐containing polyamide Mg(OH)2 nanocomposite coating on surface of poly(vinyl chloride) thin film: Study on thermal stability,flammability, and mechanical properties

Surface of poly(vinyl chloride) (PVC) thin films was coated using DOPO‐based polyamide (DBPA) coating and DBPA/Mg(OH)₂ nanocomposites (DBPN) coating by dip‐coating process. For this purpose, a new DOPO‐based dicarboxylic acid (DBDA) was synthesized and used for preparation of DBPA and organically surface modification of Mg(OH)₂ nanoparticles. The effects of DBPA and DBPN coatings on the morphology, thermal stability, combustion, and mechanical properties of PVC were investigated. The uniform dispersion of Mg(OH)₂ nanoparticles (nano‐MDH) and organically coating manner on the surface of the PVC films were confirmed by ATR‐IR spectroscopy, X‐ray diffraction (XRD), field emission scanning electron microscopy (FE‐SEM), energy dispersive X‐ray, and elemental mapping. From thermal gravimetry analysis (TGA) results, the 10 mass% loss temperature (T₁₀) increased from 268°C to 272°C in PVC coated with DBPA‐containing 10 mass% of modified Mg(OH)₂ (MMH). Also the char residue, first and second mass loss temperatures of all PVC coated were increased compared with the neat PVC film. According to microscale combustion calorimetry (MCC) results, the peak of heat release rate (pHHR) and total heat release (THR) were decreased from 128 ± 2 to 69 W/g and 12 ± 1 to 4 ± 2 KJ/g for PVC film coated with DBPA‐containing 10 mass% of MMH, compared with the neat PVC. From tensile test results, tensile strength was increased from 31.78 ± 0.8 to 39.64 ± 0.9 MPa for PVC coated with polyamide‐containing 5 mass% of MMH compared with the neat PVC.     

Ferromagnetic nanoparticle‐supported copper complex: A highly efficient and reusable catalyst for three‐component syntheses of 1,4‐disubstituted 1,2,3‐triazoles and C–S coupling of aryl halides

A new nanocatalyst was synthesized by immobilization of 4′‐(4‐hydroxyphenyl)‐2,2′:6′,2″‐terpyridine/CuI complex on ferromagnetic nanoparticles through a surface modification (FMNPs@SiO₂‐TPy‐Cu). This heterogeneous catalyst was characterized using various techniques including Fourier transform infrared and energy‐dispersive X‐ray spectroscopies, transmission and scanning electron microscopies, X‐ray diffraction, vibrating sample magnetometry and thermogravimetric analysis. The resulting nanocatalyst presented excellent catalytic activity for the regioselective syntheses of 1,4‐disubstituted 1,2,3‐triazoles and thioethers. The thermally and chemically stable, benign and economical catalyst was easily recovered using an external magnet and reused in at least five successive runs without an appreciable loss of activity.     

Structure‐activity relationship of supported Au catalysts with high catalytic activity by modifying the inactive supports

Three supported Au catalysts have been prepared by the deposition‐precipitation method by using the active carbon (AC), SiO₂‐AC, and SiO₂‐AC‐hollowed. The 3 supports were characterized by Brunauer‐Emmett‐Teller and scanning electron microscopy. Meanwhile, the supported Au nanoparticles were also characterized in detail by X‐ray powder diffraction, transmission electron microscopy, H₂‐TRP, and X‐ray photoelectron spectroscopy, and their catalytic activity and stability in CO oxidation was evaluated. The results demonstrated that Au supported on SiO₂‐AC‐hollowed exhibited much higher catalytic activity with acceptable stability for 72 hours than the other 2. We attributed to finer supported Au nanoparticles with abundant low‐coordinated Au atoms on the surfaces of hollowed supports with large special surface area and abundant pore structure. In summary, we successfully found an efficient and cheap method to prepare catalysts with high catalytic activity and acceptable stability by modifying the inactive supports.