等离子体浸没离子注入非导电聚合物的适应性及栅网诱导效应的研究

本文建立了绝缘材料等离子体浸没离子注入过程的动力学Particle-in-cell(PIC)模型, 将二次电子发射系数直接与离子注入即时能量建立关联, 研究了非导电聚合物厚度、介电常数和二次电子发射系数对表面偏压电位的影响规律以及栅网诱导效应. 研究结果表明: 非导电聚合物较厚时, 表面自偏压难以实现全方位离子注入, 栅网诱导可以间接为非导电聚合物提供偏压, 并抑制二次电子发射, 为厚大非导电聚合物表面等离子体浸没离子注入提供了有效途径.     

Sheath structure in plasma with two species of positive ions and secondary electrons

The properties of a collisionless plasma sheath are investigated by using a fluid model in which two species of positive ions and secondary electrons are taken into account. It is shown that the positive ion speeds at the sheath edge increase with secondary electron emission(SEE) coefficient, and the sheath structure is affected by the interplay between the two species of positive ions and secondary electrons. The critical SEE coefficients and the sheath widths depend strongly on the positive ion charge number, mass and concentration in the cases with and without SEE. In addition, ion kinetic energy flux to the wall and the impact of positive ion species on secondary electron density at the sheath edge are also discussed.     

电子温度各向异性对霍尔推力器BN绝缘壁面鞘层特性的影响

建立多价态多组分等离子体一维流体鞘层模型,引入电子温度各向异性系数并考虑出射电子速度分布,研究了电子温度各向异性对霍尔推力器中的BN绝缘壁面鞘层特性和近壁电子流的影响.分析结果表明,相比于纯一价氙等离子体鞘层参数,推力器中的多价态氙等离子体鞘层电势降略有降低,电子壁面损失增加,临界二次电子发射系数减小.推力器中的电子温度各向异性现象可以显著地加大出射电子能量系数,进而降低鞘层电势降,增强电子壁面相互作用.数值结果表明,空间电荷饱和机制下电子温度各向异性对鞘层空间电势分布影响显著. 关键词： 霍尔推力器 电子温度各向异性 空间电荷饱和鞘层     

二次电子发射和负离子存在时的鞘层结构特性

 建立了包括电子、离子、器壁发射二次电子以及负离子多种成分的等离子体无碰撞鞘层的基本模型,讨论了二次电子发射和负离子对1维稳态等离子体鞘层结构的影响,并且分析了多种成分等离子体鞘层内的二次电子和负离子的相互作用。结果表明：二次电子发射系数的增加和负离子含量的增加,都将导致鞘层的厚度有所减小;二次电子发射系数超过临界发射系数之后,鞘层不再是离子鞘。随着器壁材料二次电子发射系数的增加,鞘层中的负离子密度分布也逐渐增加;负离子的增加,导致二次电子临界发射系数有所增加。另外,在等离子体鞘层中二次电子发射和负离子的存在,也影响着鞘层中电子的放电特性与器壁材料的腐蚀。     

聚合物物理属性对离子注入效应的影响

聚合物导电性能差, 表面电荷积聚所产生的电容效应致使其表面电位衰减, 采用等离子体浸没离子注入对其表面改性是非常困难的. 建立了绝缘材料等离子体浸没离子注入过程的粒子模拟(PIC)模型, 实时跟踪离子在等离子体鞘层中的运动形态及特性并进行统计分析. 并基于PIC模型, 将聚合物表面的二次电子发射系数直接与离子注入即时能量建立关联, 研究了聚合物厚度、介电常数和二次电子发射系数等物理量对鞘层演化、离子注入能量和剂量的影响规律. 研究结果表明: 当聚合物厚度小于200 μ m, 相对介电常数大于7, 二次电子发射系数小于0.5时, 离子注入剂量和高能离子所占的份额与导体离子注入情况相当. 通过对聚合物表面离子注入剂量和高能离子所占份额的研究, 为绝缘材料和半导体材料表面等离子体浸没离子注入的实现提供了理论和实验依据.     

霍尔推进器壁面材料二次电子发射及鞘层特性

霍尔推进器放电通道等离子体与壁面相互作用形成鞘层,不同壁面材料的二次电子发射对推进器鞘层特性具有重要影响,本文针对推进器壁面鞘层区域建立二维物理模型,研究了氮化硼(BN)、碳化硅(SiC)和三氧化二铝(Al_2O_3)三种不同壁面材料的二次电子发射特性,在改进SiC材料二次电子发射模型的基础上,采用粒子模拟方法,讨论了壁面二次电子发射系数与电子温度和磁场强度的关系,研究了三种材料(BN,SiC和Al_2O_3)的鞘层特性,结果表明:修正的二次电子发射模型拟合曲线与实验曲线几乎一致;在相同电子温度下,三种材料(BN,SiC和Al_2O_3)的二次电子发射系数和壁面电子数密度依次增大,而鞘层电场和鞘层电势降依次减小,BN材料具有合适的二次电子发生射系数,使得霍尔推进器能在低电流下稳态工作。     

电子温度对霍尔推进器等离子体鞘层特性的影响

采用二维粒子模拟方法研究了霍尔推进器通道中电子温度对等离子体鞘层特性的影响, 讨论了不同电子温度下电子数密度、鞘层电势、电场及二次电子发射系数的变化规律. 结果表明: 当电子温度较低时, 鞘层中电子数密度沿径向方向呈指数下降, 在近壁处达到最小值, 鞘层电势降和电场径向分量变化均较大, 壁面电势维持一稳定值不变, 鞘层稳定性好; 当电子温度较高时, 鞘层区内与鞘层边界处电子数密度基本相等, 而在近壁面窄区域内迅速增加, 壁面处达到最大值, 鞘层电势变化缓慢, 电势降和电场径向分量变化均较小, 壁面电势近似维持等幅振荡, 鞘层稳定性降低; 电子温度对电场轴向分量影响较小; 随电子温度的增大, 壁面二次电子发射系数先增大后减少. 关键词： 霍尔推进器 等离子体鞘层 电子温度 粒子模拟     

不同成分等离子体鞘层的玻姆判据

在一维平板鞘层中采用流体模型分别研究了不同成分无碰撞等离子体鞘层的玻姆判据.通过拟牛顿法数值模拟了含有电子、离子、负离子以及二次电子的等离子体鞘层玻姆判据.结果表明二次电子发射增加了鞘层离子马赫数的临界值,且器壁发射二次电子温度越高,离子马赫数临界值越小.负离子使离子马赫数临界值减小.而在含有二次电子和负离子的等离子体鞘层中,当负离子较少时,二次电子发射对离子马赫数临界值影响较大;当负离子增加时,离子马赫数的临界值则主要受负离子的影响. 关键词： 鞘层 等离子体 玻姆判据     

Characteristics of wall sheath and secondary electron emission under different electron temperatures in a Hall thruster

In this paper, a two-dimensional physical model is established in a Hall thruster sheath region to investigate the influences of the electron temperature and the propellant on the sheath potential drop and the secondary electron emission in the Hall thruster, by the particle-in-cell(PIC) method. The numerical results show that when the electron temperature is relatively low, the change of sheath potential drop is relatively large, the surface potential maintains a stable value and the stability of the sheath is good. When the electron temperature is relatively high, the surface potential maintains a persistent oscillation, and the stability of the sheath reduces. As the electron temperature increases, the secondary electron emission coefficient on the wall increases. For three kinds of propellants(Ar, Kr, and Xe), as the ion mass increases the sheath potentials and the secondary electron emission coefficients reduce in sequence.     

二次电子分布函数对绝缘壁面稳态鞘层特性的影响

由于缺乏详细的理论计算和实验结果,在研究绝缘壁面稳态流体鞘层特性时,通常假设壁面出射的总二次电子服从单能分布(0)、半Maxwellian分布等.在单能电子轰击壁面的详细二次电子发射模型基础上,采用Monte Carlo方法统计发现:当入射电子服从Maxwellian分布时,绝缘壁面发射的总二次电子服从三温Maxwellian分布.进而,采用一维稳态流体鞘层模型进行对比研究,结果表明:二次电子分布函数对鞘边离子能量、壁面电势、电势及电子/离子密度分布等均具有明显影响;总二次电子服从三温Maxwellian分布时,临界空间电荷饱和鞘层无解,表明随着壁面总二次电子发射系数的增加,鞘层直接从经典鞘层结构过渡到反鞘层结构.     

霍尔推进器中磁化二次电子对鞘层特性的影响

为进一步研究霍尔推进器壁面二次电子发射对推进器性能的影响,采用流体模型数值模拟了二次电子磁化效应的等离子体鞘层特性.得到二次电子磁化鞘层的玻姆判据.讨论了不同的磁场强度和方向、二次电子发射系数以及不同种类等离子体推进器的鞘层结构.结果表明:随器壁二次电子发射系数的增大,鞘层中粒子密度增加,器壁电势升高,鞘层厚度减小;鞘层电势及粒子密度随着磁场强度和方位角的增加而增加;而对于不同种类的等离子体,壁面电势和鞘层厚度也不同.这为霍尔推进器的磁安特性实验提供了理论解释. 关键词： 霍尔推进器 磁鞘 二次电子     

Numerical study on discharge characteristics influenced by secondary electron emission in capacitive RF argon glow discharges by fluid modeling

A one-dimensional(1D) fluid model of capacitive RF argon glow discharges between two parallel-plate electrodes at low pressure is employed. The influence of the secondary electron emission on the plasma characteristics in the discharges is investigated numerically by the model. The results show that as the secondary electron emission coefficient increases,the cycle-averaged electric field has almost no change; the cycle-averaged electron temperature in the bulk plasma almost does not change, but it increases in the two sheath regions; the cycle-averaged ionization rate, electron density, electron current density, ion current density, and total current density all increase. Also, the cycle-averaged secondary electron fluxes on the surfaces of the electrodes increase as the secondary electron emission coefficient increases. The evolutions of the electron flux, the secondary electron flux and the ion flux on the powered electrode increase as the secondary electron emission coefficient increases. The cycle-averaged electron pressure heating, electron Ohmic heating, electron heating, and ion heating in the two sheath regions increase as the secondary electron emission coefficient increases. The cycle-averaged electron energy loss increases with increasing secondary electron emission coefficient.     

One-dimensional solution to the stable, space-charge-limited emission of secondary electrons from plasma-wall interactions

Numerical solutions to the stable, space-charge-limited emission of secondary electrons from plasma-wall interaction are found based on one-dimensional plasma moment equations that assume cold ions, Maxwellian electrons and cold secondary electrons. The numerical method finds a range of plasma parameters that permit stable emission of secondary electrons in the absence of normal electric fields to the wall. These solutions were not obtained with previous method that solves only for the marginally stable plasma sheath. Range of the ion Mach number at the sheath edge, the floating wall potential relative to the plasmas, and secondary electron emission coefficients corresponding to the vanishing normal electric fields are found for hydrogen, argon and xenon plasmas. The results show that a relatively small range of secondary electron emission coefficient exists to allow stable sheaths structures along with larger ranges of ion injection speed at the sheath edge and floating potential of the emitting wall.     

Nonlinear collisional monte carlo simulations for high-temperature SOL plasma

A nonlinear Monte Carlo collisional model is applied to to investigate scrape-off layer (SOL) plasmas with high temperatures. In the proposed SOL modeling, A steady state SOL plasma, which satisfies the particle and energy balances and neutrality constraint, is determined in terms of total particle and heat fluxes across the separatrix, the edge plasma temperature, the secondary electron emission coefficient, and the SOL size. A conductive heat flux into the SOL is effectively modeled via random exchange of source particles and the SOL plasma particles. It is found that the potential drop and the electron transmission factor in the collisional SOL plasma are in good agreement with the theoretical prediction. The cooling effect of secondary electrons in the high temperature divertor operation is investigated. In such a collisionless plasma, the present nonlinear collision model is useful because the electron distribution function deviates far from a Maxwellian distribution. In the presence of strong secondary electron emission, the electron sheath energy transmission factor in the collisionless regime is found to be significantly smaller than that in the collisional regime. This fact suggests that a high-temperature divertor operation can be possible.     

On characteristics of sheath damping near a dielectric wall with secondary electron emission

A preliminary investigation is conducted to study the characteristics of sheath damping near a dielectric wall with secondary electron emission (SEE). Making use of the linear analysis of the sheath stability, we have found two major contributions to the sheath damping, one similar to the Landau damping in uniform plasmas and another determined by local electric field and electron density of the steady-state sheath. It indicates that in a classical sheath regime the damping in the sheath region monotonically increases towards the wall and decreases with the enhancement of SEE effect. In order to verify the theoretical analysis, sheath oscillation processes induced by an initial disturbance are simulated with a time-dependent one-dimensional (1D) sheath model. Numerical results obtained are consistent with the theoretical analysis qualitatively.     

Fluid Model of a Sheath Formed in Front of an Electron Emitting Electrode Immersed in a Plasma with Two Electron Temperatures

The formation of a sheath in front of a negatively biased electrode (collector) that emits electrons is studied by a one‐dimensional fluid model. Electron and ion emission coefficients are introduced in the model. It is assumed that the electrode is immersed in a plasma that contains energetic electrons. The electron velocity distribution function is assumed to be a sum of two Maxwellian distributions with two different temperatures, while the ions and the emitted electrons are assumed to be monoenergetic. The condition for zero electric field at the collector is derived. Using this equation the dependence of electron and ion critical emission coefficients on various parameters ‐ like the ratio between the hot and cool electron density, the ratio between hot and cool electron temperature and the initial velocity of secondary electrons ‐ is calculated for a floating collector. A modification of the Bohm criterion due to the presence of hot and emitted electrons is also given. The transition between space charge limited and temperature limited electron emission for a current‐carrying collector is also analyzed. The critical potential, where this transition occurs, is calculated as a function of several parameters like the Richardson emission current, the ratio between the hot and cool electron density, the ratio between hot and cool electron temperature and the initial velocity of secondary electrons. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

霍尔推进器中振荡鞘层对电子与壁面碰撞频率的影响研究

利用二维粒子模拟方法研究振荡鞘层对近壁电导的影响.研究结果表明,当二次电子发射系数大于1时,鞘层处于振荡状态.在振荡鞘层状态下,电子与壁面的碰撞通量沿平行与壁面方向剧烈的周期性振荡,振荡的波长为电子静电波波长量级,电子与壁面的碰撞频率高出经典鞘层状态下电子与壁面碰撞频率1—2个数量级,此时的碰撞频率对通道中电流的贡献不可忽略.振荡鞘层相对与经典鞘层增大了电子与壁面的碰撞频率,但是振荡鞘层的存在,仍然会使一部分慢电子无法穿越鞘层的势垒而打到壁面. 关键词： 霍尔推进器 振荡鞘层 二次电子     

壁面二次电子发射对霍尔推力器放电通道绝缘壁面双鞘特性的影响

为进一步揭示霍尔推力器放电通道绝缘壁面鞘层的特性, 利用考虑了壁面二次电子分布函数的一维稳态流体鞘层模型, 研究了壁面二次电子发射对近壁双鞘特性的影响. 分析结果表明, 由于壁面发射的二次电子对近壁鞘层中的电子密度有增加作用, 存在一个临界二次电子发射系数σ_dc使得: 当σ≤σ_dc时, 鞘层为单层的正离子鞘结构; 当σ>σ_dc时, 鞘层表现为双层的正离子鞘和电子鞘相连结构, 连接点对应于垂直于壁面方向上电势分布的拐点. 然而, 当σ进一步增大到0.999时, 鞘层转变为三层的正离子鞘-电子鞘-正离子鞘交替结构. 数值结果表明: 随着σ的增加, 电子鞘与离子鞘的连接点向远离壁面的方向移动, 电子鞘的厚度逐渐增加; 随着壁面出射电子能量系数a的增加, 近壁区鞘层的厚度也逐渐增加. 关键词： 霍尔推力器 双鞘 壁面二次电子发射     

杂质离子对等离子体边界参量的影响

采用一维流体模型研究了含有杂质离子的等离子体与器壁材料相互作用给边界等离子体参量带来的影响.通过数值模拟,研究了分别选用碳和钨作为器壁材料时,器壁温度不同情形下热发射产生的电子对等离子体器壁电势、电场强度、热发射电子流以及沉积器壁离子动能流的影响.研究结果发现,当面向等离子体材料表面温度升高时,器壁电势和热发射产生的电流将增加,器壁电场强度和离子沉积器壁动能流则会减小,并且钨作为器壁材料要比碳作为器壁材料对于等离子体边界参量影响更明显.此外,研究了钨作为器壁材料时,碳杂质离子（浓度和电荷数）对等离子体器壁参量的影响.     

两种温度电子对稳态等离子体鞘层的影响

建立包含冷热电子的无碰撞等离子体鞘层的流体模型,利用数值模拟研究含有两种温度电子时等离子体鞘层的产生.结果表明:对于含有两种不同温度电子的稳态等离子体,冷电子的温度越低或者冷电子的含量越多,鞘边离子的马赫数临界值就越小,鞘层的宽度就变得越窄,沉积器壁的离子动能流也就越少.此外,研究不同种类的等离子体(Ar、Ke、Xe),鞘层厚度和离子沉积器壁动能流受冷电子的影响.