螺旋管内高压汽水两相流动沸腾干涸点的研究

在较宽的实验参数范围内(系统压力P=8～15 MPa,质量流速G=800～1800 kg·m~(-2)·s~(-1),壁面热流密度q_w=200～950 kW·m~(-2))对一立式螺旋管内(管内径为10 mm,螺旋直径为300 mm,节距为50 mm)汽水两相流动沸腾干涸特性进行了实验研究。通过研究,获得了干涸发生时螺旋管圈壁温的分布特征以及压力、质量流速和壁面热流密度这三个参数对临界干度的影响规律。同时在实验数据的基础上,提出了一个适用于计算螺旋管内高压高含汽率工况下汽水两相流临界干度的经验关系式。     

高质量流速下立式螺旋管内汽液两相传热特性研究

对高质量流速下立式螺旋管内高压汽液两相流沸腾传热特性进行了试验研究,参数范围为:系统压力8.0～15.0MPa;质量流速2500～4000kg/m2s;壁面热流密度200～1000kW/m2;实验段为Φ14的不锈钢管弯制而成的螺旋管直径比为D/d=30.1的管圈,总长为2.335m,考察了热流密度和质量流速对两相传热的影响,分析核态沸腾和两相强制对流沸腾机理在螺旋管内两相传热中所起的作用,得到了局部传热系数的分布特性和平均传热系数计算关联式,首次发现高质量流速区域内螺旋管内汽液两相传热效果亦趋近于相同条件下直管内的换热系数,并对已有的结论进行了分类比较分析.     

立式螺旋管汽液两相流沸腾传热恶化实验研究

本文实验研究了低质量流速(500～800 kg·m~(-2)·s~(-1))下的立式螺旋管临界热负荷,对沸腾传热恶化壁温特性和螺旋管临界热负荷影响因素进行分析.并同前人工作汇总,以流量,压力和临界干度为参数,建立了基于局部条件假设的立式螺旋管临界热负荷查询表(Look-Up-Table),共272个点.压力范围6.5～21 MPa,质量流速范围500～1800 kg·m~(-2)·s~(-1).     

R134a卧式螺旋管内沸腾流型与阻力特性实验研究

在蒸发温度为5～15℃,热流密度范围为5～20 kW·m~(-2),工质质量流速变化范围为50～500kg·m~(-2)·s~(-1)和干度范围为0.01～0.9的条件下,对R134a在卧式螺旋管内的流动沸腾流型及阻力特性进行了实验研究。利用可视化技术对R134a在卧式螺旋管内的流动沸腾流型进行了观察分析,发现了两种新流型,对卧式螺旋管的上升段和下降段分别建立了流型图。获得了阻力特性的基础数据,通过对实验数据回归分析,发展了摩擦阻力系数计算关联式。     

非均匀加热立式螺旋管内沸腾传热恶化特性研究

本文主要开展非均匀加热螺旋管内沸腾传热恶化特性实验研究。实验参数范围为:热流密度15~55 kW·m^-2;质量流速190~400 kg·m^-2·s^-1;压力0.8~1.1 MPa。实验包括一个均匀加热实验段及两个非均匀加热实验段,三个实验段尺寸一致,不均匀度分别为1.0,1.2和1.4。实验过程中共获得三种壁温飞升现象,而且发现随着质量流速及不均匀度的增大传热恶化位置逐渐向内侧管圈偏移,并由此导致非均匀加热螺旋管内初始烧干干度随着质量流速的变化规律与均匀加热螺旋管恰好相反。     

水平管内乙烷饱和流动沸腾传热实验研究

本文对乙烷在内径为8 mm的水平管内进行了饱和流动沸腾传热特性的实验测量。实验测量的压力范围为0.35～0.57 MPa,热流范围为13.2～65.9 kW·m~(-2),流量范围为55.3～92.2 kg·m~(-2)·s~(-1),并系统分析了质量流量、热流密度、含气率对饱和流动沸腾传热系数的影响。最后将实验结果同九种关联式进行了比较,渐进模型的两种关联式和增强模型的两种关联式计算结果较好,平均偏差都小于15%。     

高参数小管径内煤油的传热特性研究

本文对酸碱水洗煤油在高热流密度、高流速、高压、小直径圆管条件下进行了试验及理论研究,试验参数为热流密度q=0.8-50 MW/m2、亚临界压力p=2 MPa、超临界压力p=5,15 MPa、质量流速pw=8500-51000 kg/m2·s、圆管内径φ=1.7 mm。通过试验研究,获得了酸碱水洗煤油在亚临界及超临界压力条件下的传热特性、拟沸腾发生的界限条件以及传热恶化时的临界热流密度值及相关影响因素。在对试验结果分析的基础上,建立了临界热流密度关联式,计算结果与试验结果吻合良好。     

微细通道内非共沸工质流动沸腾换热实验研究

本文实验研究了非共沸混合制冷剂R134a/R245fa(质量比为0.7/0.3)在长度为45 mm、65 mm的平行微通道内的流动沸腾特性。微通道由30个截面为0.5 mm×0.5 mm矩形微通道组成。得到了质量流速在542.22～995.56kg·m~(-2)·s~(-1)、热流密度在4.9～100.2 W·cm~(-2)时的流动沸腾传热系数,并对R134a/R245fa和R134a的换热系数进行对比,结果表明热流密度、质量流速、通道长度对换热系数均有影响。考虑R134a/R245fa相变时的附加传质阻力对换热的影响下,在纯工质关联式中引入混合物影响因子,得到了适用于本实验工况下R134a/R245fa的关联式。     

R32在微细光管内流动沸腾的数值研究

利用Mixture多相流模型对R32在2 mm水平微细光管内流动沸腾进行了三维稳态数值模拟。模拟的工况范围为:质量流速200~400 kg/(m~2s),热流密度10~40 kW/m~2,饱和温度15~20℃。结果表明:质量流速的增加消弱了重力对两相分布的影响;热流密度的增加强化了壁面附近的核态沸腾。数值模拟的换热系数和压降与实验结果的平均偏差分别为11.3%和-1.1%。     

CO2在细径管内蒸发换热的实验研究

对CO2在细径管内蒸发换热特性进行了研究。试验管为内径4 mm长为0.5 m的光滑紫铜管。实验中参数变化范围为,蒸发温度1-15℃,质量流速100-300 kg/m2s,热流密度2-18 kW/m2,干度0.1-0.9。实验结果表明CO2 蒸发换热系数高于氟利昂类制冷剂,蒸发温度和热流密度对换热系数影响显著,而质量流速的影响相对较弱,传统制冷剂的换热系数关联式不适用于CO2;二氧化碳的压力损失随着热流密度和质量流速的增加而增加,随着蒸发温度的上升而减小,CO2压力损失小于氟利昂类制冷剂。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.     

Fiber Modal Index Measurements Based on Fiber Gratings

A novel method based on fiber gratings for measuring the effective indices of fiber modes is proposed. The effective index difference between the core mode and a cladding mode was obtained by analyzing the interference fringe of a pair of cascaded long-period fiber gratings. In order to extract the core mode index from the measured index difference, an index matching oil immersion method is proposed. By analyzing the interaction between the cladding mode and the oil applied on the cladding surface, the mode order and the effective index of the involved cladding mode might be calculated. Experimental results about the interference fringe shifts induced by the oil index and the oil-applied length are also presented.     

Optical Pulse Compression Schemes That Use Nonlinear Bragg Gratings

Nonlinear optical pulse compression of picosecond pulses typically requires long lengths of optical fiber and multiple components. Periodic structures, such as fiber Bragg gratings, are highly dispersive at wavelengths outside of the photonic bandgap. This implies that such gratings can be used as very short all-fiber compressors. In this paper a number of such compression schemes are reviewed involving uniform and nonuniform fiber Bragg gratings, relying on both soliton and nonsoliton compression principles. Experimental results supporting the corresponding underlying theory are also presented. Finally, an extension of one of the compression schemes is shown, which allows the generation of adjustable high-repetition rate soliton trains.