样品温度对纳秒激光诱导Cu等离子体特征参数的影响

为了研究样品温度对激光诱导击穿Cu等离子体特征参数的影响,以黄铜为研究对象,在优化的实验条件下采用波长为532 nm的Nd∶YAG纳秒脉冲激光诱导激发不同温度下的块状黄铜,测量了Cu等离子体的特征谱线强度和信噪比;同时在局部热平衡条件下利用Boltzmann斜线法和Stark展宽法分析计算了不同的样品温度条件下等离子体电子温度和电子密度。实验结果表明,在激光功率为60 mW时,随着样品温度的升高,Cu的特征谱线强度和信噪比逐渐增加,样品温度为130 ℃时达到最大值,然后趋于饱和。计算表明,黄铜样品中Cu元素Cu Ⅰ 329.05 nm,Cu Ⅰ 427.51 nm,Cu Ⅰ 458.71 nm,Cu Ⅰ 510.55 nm,Cu Ⅰ 515.32 nm,Cu Ⅰ 521.82 nm, Cu Ⅰ 529.25 nm,Cu Ⅰ 578.21 nm八条谱线在130℃的相对强度相较于室温（18 ℃）下分别提高了11.55倍、4.53倍、4.72倍,3.31倍、4.47倍、4.60倍、4.25倍、4.55倍,光谱信噪比分别增大了1.35倍,2.29倍、1.76倍、2.50倍、2.45倍、2.28倍、2.50倍,2.53倍。分析认为,升高样品温度会增大样品的烧蚀质量,相对于温度较低状态增加了等离子体中样品粒子浓度,进而提高等离子体发射光谱强度。所以,适当升高样品温度能够提高谱线强度和信噪比,从而增强LIBS技术检测分析光谱微弱信号的测量精度,改善痕量元素的检测灵敏度。同时研究了改变样品温度时等离子体电子温度和电子密度的变化趋势。计算表明,当样品温度从室温上升到130 ℃的过程中,等离子体的电子温度由4 723 K上升到7 121 K时基本不再变化。这种变化规律与发射谱线强度和信噪比变化趋势一致。分析认为,这主要是由于在升高样品温度的初始阶段,激光烧蚀量增大,等离子体内能增大,从而导致等离子体电子温度升高。当激光烧蚀样品的量达到一定值后不再变化,激光能量被激发溅射出来的样品蒸发物以及尘粒的吸收、散射和反射,导致激光能量密度降低,电子温度趋于饱和,达到某种动态平衡。选用一条Cu原子谱线（324.75 nm）的Stark展宽系数计算激光等离子体的电子密度,同时研究改变样品温度时等离子电子密度的变化趋势,计算表明在样品温度为130 ℃时,Cu Ⅰ 324.75 nm对应的等离子电子密度相较于室温（18 ℃）条件下增大了1.74×1017 cm-3。该变化趋势与电子温度的变化趋势一致。适当升高样品温度使得电子密度增大,从而提高电子和原子的碰撞几率,激发更多的原子,这是增强光谱谱线强度的原因之一。由此可见,升高样品温度是一种便捷的提高LIBS检测灵敏度的有效手段。     

样品温度对纳秒激光诱导土壤等离子体辐射特性的影响

利用脉宽8 ns,波长为532 nm的Nd:YAG单脉冲纳秒激光器,在一个标准大气压下入射到土壤中(样品土壤来自蚌埠学院校园),改变样品温度,获得了不同样品温度下激光诱导击穿光谱. 通过分析光谱,得到土壤中不同特征谱线的强度和信噪比. 分别利用Boltzmann斜线法和Stark展宽法计算并分析了等离子体电子温度和电子密度随样品温度的演化规律;同时讨论了提高样品温度和激光诱导土壤等离子体辐射增强的原因. 实验结果表明,随着样品温度的升高,等离子体的谱线强度、信噪比、电子温度和电子密度会逐渐增强,并且在温度为100 °C时达到最大.     

样品温度对纳秒激光诱导土壤等离子体辐射特性的影响（英文）

利用脉宽8 ns,波长为532 nm的Nd:YAG单脉冲纳秒激光器,在一个标准大气压下入射到土壤中(样品土壤来自蚌埠学院校园),改变样品温度,获得了不同样品温度下激光诱导击穿光谱.通过分析光谱,得到土壤中不同特征谱线的强度和信噪比.分别利用Boltzmann斜线法和Stark展宽法计算并分析了等离子体电子温度和电子密度随样品温度的演化规律;同时讨论了提高样品温度和激光诱导土壤等离子体辐射增强的原因.实验结果表明,随着样品温度的升高,等离子体的谱线强度、信噪比、电子温度和电子密度会逐渐增强,并且在温度为100℃时达到最大.     

样品温度和空间约束两种方法相结合对激光诱导击穿光谱的影响

升高样品温度和采用空间约束能提高激光诱导击穿光谱的信号强度,两种技术的结合可以进一步提高激光诱导击穿光谱的光谱强度.本文在空气环境中研究了升高样品温度和空间约束效应两种方法相结合对激光诱导击穿光谱的影响,测量了激光诱导铝等离子体的时间分辨光谱.实验结果表明:升高样品温度能增加激光诱导击穿光谱的信号强度,高温样品能耦合更...     

不同样品温度下聚焦透镜到样品表面距离对激光诱导铜击穿光谱的影响

研究了不同温度下聚焦透镜到样品表面距离对激光诱导击穿光谱(laser-induced breakdown spectroscopy,LIBS)强度的影响,使用Nd:YAG脉冲激光激发样品并产生等离子体,探测的等离子体发射的光谱线为Cu(Ⅰ)510.55 nm,Cu(Ⅰ)515.32 nm和Cu(Ⅰ)521.82 nm.使用透镜的焦距为200 mm,测量的聚焦透镜到样品表面距离的范围为170—200 mm,样品温度从25℃升高到270℃,激光能量为26 mJ.总体上,升高样品温度能有效地提高LIBS光谱的辐射强度.在25℃和100℃时,光谱强度随着聚焦透镜到样品表面距离的增加而单调增加;在样品温度更高(150, 200, 250和270℃)时,光谱强度随着距离的增加出现先升高而后又降低的变化.同时,在样品接近焦点附近,随着样品温度的升高,LIBS光谱强度的变化不明显,还可能出现光谱强度随着样品温度升高而降低的情况,这在通过升高样品温度来提高LIBS光谱强度中特别值得我们注意.为了更进一步了解这两个条件对LIBS的影响,计算了等离子体温度和电子密度,发现等离子体温度和电子密度的变化与光谱强度的变化几乎一致,更高样品温度下产生的等离子体温度和电子密度更高.     

磁约束技术对激光诱导等离子体辐射特性的影响

为了提高激光诱导击穿光谱质量,利用Nd:YAG激光器烧蚀土壤样品,研究了磁场作用下的激光诱导等离子体辐射特性。实验结果表明,在相同激光输出能量条件下,随着磁场强度的增大,等离子体的辐射强度逐渐增强。计算可知,当采用的磁场强度为0.5T时,样品元素Al,Fe,Ba和Ti的光谱线强度比无磁场作用时的分别增强了52.35%,46.64%,64.01%和51.73%,光谱信噪比分别提高了45.44%,69.64%,40.26%和41.33%;而等离子体的电子温度和电子密度分别提高了1 355.01K和0.53×1016cm-3。可见,利用磁场约束等离子体的技术是提高激光光谱质量的一种有效方法。     

KCl添加剂对激光诱导土壤等离子体辐射强度的影响

为了提高激光诱导击穿光谱技术对低含量物质成分的检测能力,实验研究了KCl添加剂对土壤样品发射光谱的增强效应。利用高能量钕玻璃脉冲激光器烧蚀样品,由组合式多功能光栅光谱仪和CCD数据采集处理系统记录等离子体光谱,并通过测量光谱线的强度和Stark展宽分别计算了等离子体的电子温度和电子密度。实验结果证明,随着KCl加入量的增加,激光等离子体的光谱强度、信背比、电子温度和电子密度均呈现出先增大而后减小的规律。当KCl加入量为15%时,等离子体辐射最强,元素Mn,Fe,和Ti的谱线强度分别比无添加剂时提高了2.23,1.13和2.04倍,信背比分别提高了1.33,0.89和0.94倍;而等离子体的温度和电子密度比无添加剂时分别提高了14%和38%。     

平面反射镜装置对激光诱导等离子体辐射特性的影响

为获得高质量的发射光谱,提出了一种平面反射镜装置,研究了在平面反射镜装置条件下的激光诱导等离子体辐射特性。实验结果表明,相同的激光输出能量条件下,在等离子体周围放置由三块平面反射镜组成的装置以后,土壤样品中元素Mg,Fe,Ba,Ti和Al的光谱线强度比常态下的分别增大了116.2%,96.43%,90.93%,102.1%和98.57%,信噪比分别提高39.17%,32.48%,38.07%,39.95%和21.30%。通过测量激光等离子体参数,解释了平面反射镜装置对等离子体辐射增强的机理。这种简便易行的方法是改善激光诱导击穿光谱技术检测能力的有效途径。     

NaCl对激光诱导土壤等离子体辐射的增强效应

为了改善激光诱导击穿光谱质量,采用Nd:YAG激光器输出的纳秒脉冲激光激发土壤样品,由光栅光谱仪和光电检测系统记录等离子体发射光谱,研究了激光输出能量（100~500 mJ）和NaCl样品添加剂（质量分数0%~20%）对等离子体辐射强度的影响。实验结果表明,在激光能量为200 mJ的优化条件下,可以提高光谱强度和信噪比,而更高激光能量诱导的等离子体中光谱线自吸严重。当土壤样品中加入适量NaCl添加剂以后,能够进一步改善激光光谱质量。NaCl加入量为10%时,等离子体中元素Fe,Ba,Al和Ti的谱线强度比无添加剂时分别提高了37%,32%, 32% 和70%,光谱信噪比分别提高了33%,26%,16% 和38%。而样品烧蚀量、电子温度和电子密度比无添加剂时分别提高了14%,9.6%和26%。     

基于激光诱导击穿光谱技术定量分析食用明胶中的铬元素

利用激光诱导击穿光谱技术对食用明胶样品中的铬元素进行定量分析.采用Nd:YAG脉冲激光器三倍频输出的355 nm激光诱导击穿食用明胶产生激光等离子体,测量等离子发射光谱.实验数据表明:使用内标法定量分析食用明胶样品中铬元素浓度分别为10—200 ppm(1 ppm=10-6)时,铬元素含量与分析谱线(CrI:245.43 nm)强度之间具有很好的线性关系.分析了光谱探测延迟时间对明胶中铬元素激光诱导击穿光谱的影响,利用信号强度与信噪比获得了优化的光谱探测延迟时间实验参数.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.