多壁碳纳米管-酰基吡唑啉酮复合膜修饰电极测定异烟肼

报道了一种修饰电极--多壁碳纳米管-酰基吡唑啉酮复合膜修饰玻碳电极(MWNTs/HPMαFP/GCE ),研究了异烟肼在此修饰电极上的电化学行为及反应机理.与裸GCE和MWNTs/GCE相比,异烟肼在MWNTs/HPMαFP/GCE上的氧化峰电流和检测灵敏度大大提高,表明多壁碳纳米管和酰基吡唑啉酮产生了协同增效作用.在...     

螺旋碳纳米管修饰电极对硫利达嗪的测定

螺旋碳纳米管(HCNTs)作为一种新型碳纳米材料具有比表面积大、催化性能好等特点。本文采用循环伏安法,研究了盐酸硫利达嗪(TR)在HCNTs修饰玻碳电极(HCNTs/GCE)上的电化学行为。HCNTs/GCE与裸玻碳电极及碳纳米管修饰的玻碳电极相比,对TR具有更强的催化氧化性能,其差分脉冲伏安法的峰电流与浓度在18.67~122.7μmol/L范围内呈良好的线性关系,检出限为5.120μmol/L。     

聚(3-氨基-5-巯基-1,2,4-三唑)/多壁碳纳米管修饰的玻碳电极同时检测尿酸、黄嘌呤与次黄嘌呤

采用滴涂法得到多壁碳纳米管(MWCNTs)修饰的玻碳电极(GCE),通过电沉积方法将3-氨基-5-巯基-1,2,4-三唑(TA)沉积在MWCNTs/GCE表面,制备了聚(3-氨基-5-巯基-1,2,4-三唑)/多壁碳纳米管修饰电极(p TA/MWCNTs/GCE)。采用循环伏安法(CV)和示差脉冲伏安法(DPV),研究了尿酸(UA)、黄嘌呤(XA)和次黄嘌呤(HX)在该修饰电极上的电化学行为。结果表明,该修饰电极对UA、XA和HX均有较好的电催化活性作用,能实现对3种物质的同时测定。UA、XA和HX在该修饰电极上的线性范围分别为9.0~739.0、2.0~259.0、1.0~353.0μmol/L;检出限分别为0.67、0.17、0.33μmol/L。该修饰电极已成功用于尿液和血清实际样品中UA、XA和HX的同时测定,回收率为98.8%~105.5%。     

碳纳米管修饰电极上沙丁胺醇电催化氧化研究

将多壁碳纳米管(MWNT)分散在疏水性表面活性剂双十六烷基磷酸(DHP)溶液中形成稳定、均相的分散液,然后制备多壁碳纳米管-DHP复合膜修饰玻碳电极(MWNT-DHP/GCE).应用方波伏安法研究了沙丁胺醇在修饰电极上的电化学行为,结果表明,碳纳米管复合膜修饰电极对沙丁胺醇的氧化有良好的电催化活性,其氧化反应为一电子一质子过程,氧化电位比裸玻碳电极负移40 mV,峰电流增加了4.5倍.在最佳测试条件下,氧化峰电流与沙丁胺醇浓度在8.3×10-7~3.3×10-6mol/L范围内呈良好线性关系,开路富集2min,检出限达1.8×10-7mol/L.该修饰电极具有良好的重现性、稳定性.     

咖啡酸在多壁碳纳米管修饰玻碳电极上的电化学行为及其测定

制备了多壁碳纳米管(MWNT)修饰玻碳电极,并研究了咖啡酸在该电极上的电化学行为及其测定方法,与裸玻碳电极(GCE)相比,MWNT膜修饰电极(MWNT/GCE)能显著提高咖啡酸的氧化峰电流.在pH=3.29的B-R缓冲溶液中,咖啡酸在MWNT/GCE电极上出现1对准可逆的氧化还原峰,Epa=0.47 V,Epc=0.32 V,峰电流与其浓度在5.0×10-7～2.0×10-5 mol/L范围内成线性关系,检出限为5.0×10-7mol/L.实际样品测定的相对标准偏差(RSD)为0.82％(n=5),平均回收率为100.7％.MWNT膜对咖啡酸的电化学氧化有明显的催化作用.该法是一种快捷、可靠、灵敏的检测方法,可以用于咖啡酸含量的测定.     

曲克芦丁在羧基化单壁碳纳米管修饰电极上的电化学氧化

研制了羧基化单壁碳纳米管修饰玻碳电极( SWCNTs - COOH/GCE).用交流阻抗谱法(EIS)和扫描电镜( SEM)研究了电极膜性能,应用循环伏安法(CV)考察了曲克芦丁在修饰电极上的电化学行为.结果表明,SWCNTs - COOH修饰电极对曲克芦丁的氧化有良好的电催化活性,其氧化反应为单电子单质子过程,结合恒...     

盐酸氯丙嗪-联吡啶钌体系在多壁碳纳米管修饰电极上的电化学发光行为研究及盐酸氯丙嗪的测定

在玻碳电极上成功制备了多壁碳纳米管修饰电极(MWCNTs/GCE),优化了该修饰电极的制备条件.研究了联吡啶钌和盐酸氯丙嗪在该修饰电极上的电化学行为和电化学发光行为,建立了电化学发光法测定尿液中盐酸氯丙嗪的分析方法.结果表明,联吡啶钌-氯丙嗪体系在MWCNTs/GCE上表现出很好的电化学活性和电致化学发光响应,多壁碳纳米管不但增大了玻碳电极的比表面积而且加快了联吡啶钌在电极表面的电化学氧化,对联吡啶钌的电化学发光强度具有明显的增敏作用,同时盐酸氯丙嗪对联吡啶钌在该修饰电极上的电致化学发光具有很强的增敏作用.在0.1 mol/L的磷酸盐(pH 7.5)缓冲溶液中,盐酸氯丙嗪在该修饰电极上的检出限(S/N=3)为6.0×10-7 mol/L,在1.0×10-6 ～4.0×10-4 mol/L范围内浓度与相对发光强度呈线性关系(r=0.995 2).连续测定6.0×10-5 mol/L的盐酸氯丙嗪溶液13次,发光强度的RSD值为2.50%,表明该修饰电极具有较好的重复性.该方法已经成功地应用于尿样的检测.     

基于金纳米粒子/聚阿魏酸/多壁碳纳米管修饰电极的DNA计时库仑法生物传感器的制备

构建了基于金纳米粒子/聚阿魏酸/多壁碳纳米管(AuNPs/PFA/MWCNTs)修饰电极的DNA计时库仑法生物传感器.利用循环伏安技术在多壁碳管修饰的玻碳电极表面上聚合一层阿魏酸,在恒电位条件下,在阿魏酸表面沉积金纳米粒子,巯基DNA作为探针通过金硫键固定在金纳米粒子表面.电化学交流阻抗技术(EIS)与扫描电镜(SEM...     

多壁碳纳米管-离子液体凝胶修饰电极对放线菌素D的高灵敏检测

以多壁碳纳米管和离子液体1-正丁基-3-甲基咪唑六氟磷酸盐(BMIMPF6)为修饰剂,研制了多壁碳纳米管-离子液体凝胶修饰玻碳电极(MWNTs-BMIMPF6/GCE),并研究了放线菌素D在该电极上的电化学行为。实验结果表明,放线菌素D于-0.09 V处有一明显的氧化峰,在pH=4.8的HAc-NaAc缓冲溶液中,放线菌素D在该修饰电极上产生的氧化峰电流比在多壁碳纳米管修饰玻碳电极上显著增大。在选定实验条件下,放线菌素D的氧化峰电流与其浓度在2.0×10-8~8.0×10-7mol/L的范围内呈良好的线性关系,检出限为7.5×10-9mol/L。该方法可用于注射液中放线菌素D的测定。     

单壁碳纳米管-氨基二茂铁复合物修饰玻碳电极对对硝基苯酚的电化学检测

本研究用氨基二茂铁(Aminoferrocene,AFc)经重氮化反应后修饰单壁碳纳米管(SWNTs),制备SWNTs-AFc复合物,并以该复合物修饰玻碳电极(GCE),通过循环伏安法(CV)和差分脉冲伏安法(DPV)等电化学方法检测对硝基苯酚(p-NP)。结果表明,与裸玻碳电极相比,SWNTs-AFc/GCE对p-NP响应的还原过电位显著减小,峰电流大大增强,p-NP的检测线性范围为1~850μmol/L(R2=0.997),检测限为1μmol/L。该方法电流响应快、灵敏度高、检测限低,具有良好的应用前景。     

Sensitive voltammetric determination of paracetamol by poly (4-vinylpyridine)/multiwalled carbon nanotubes modified glassy carbon electrode

A novel glassy carbon electrode (GCE) modified with a composite film of poly (4-vinylpyridine) (P4VP) and multiwalled carbon nanotubes (P4VP/MWCNT GCE) was used for the voltammetric determination of paracetamol (PCT). This novel electrode displayed a combined effect of P4VP and MWCNT on the electro-oxidation of PCT in a solution of phosphate buffer at pH 7. Hence, conducting properties of P4VP along with the remarkable physical properties of MWCNTs might have combined effects in enhancing the kinetics of PCT oxidation. The P4VP/MWCNT GCE has also demonstrated excellent electrochemical activity toward PCT oxidation compared to that with bare GCE and MWCNT GCE. The anodic peak currents of PCT on the P4VP/MWCNT GCE were about 300 fold higher than that of the non-modified electrodes. By applying differential pulse voltammetry technique under optimized experimental conditions, a good linear ratio of oxidation peak currents and concentrations of PCT over the range of 0.02–450 μM with a limit of detection of 1.69 nM were achieved. This novel electrode was stable for more than 60 days and reproducible responses were obtained at 99% of the initial current of PCT without any influence of physiologically common interferences such as ascorbic acid and uric acid. The application of this electrode to determine PCT in tablets and urine samples was proposed.     

延胡索酸泰妙菌素在乙炔黑-离子液体复合修饰玻碳电极上的电化学行为及电分析方法

用乙炔黑(Acetylene black,AB)和离子液体(Ionic liquid,IL)制备了乙炔黑-离子液体复合修饰玻碳电极(AB-ILs/GCE),并用电化学阻抗谱(EIS)进行了表征。采用循环伏安法(Cyclic voltammetry,CV)和计时电流法(Chronoamperometry,CA),方波伏安法(Square wave voltammetry,SWV)研究了延胡索酸泰妙菌素(TF)在此电极上电化学行为及电化学动力学性质。结果表明,TF在玻碳电极(GCE)上于0.74 V处出现一个不可逆氧化峰,与GCE相比TF在AB/GCE上的氧化峰电位基本不变,氧化峰电流增大1.8倍;而与AB/GCE相比,TF在AB-ILs/GCE上的氧化峰电位略有负移,氧化峰电流增大3倍。实验结果表明,AB-ILs/GCE对TF电化学氧化有明显的催化作用。同时考察了实验条件对TF电化学行为的影响,测定了电极反应过程动力学参数,并用本方法对TF针剂中TF含量进行了定量测定,RSD在1.1%～2.9%之间,加标回收率在98.6%～101.8%之间。据此建立了TF电化学定量测定方法。     

Amperometric sulfite sensor based on multiwalled carbon nanotubes/ferrocene-branched chitosan composites

A novel amperometric sensor for the determination of sulfite was fabricated based on multiwalled carbon nanotubes (MWCNTs)/ferrocene-branched chitosan (CHIT-Fc) composites-covered glassy carbon electrode (GCE). The electrochemical behavior of the sensor was investigated in detail by cyclic voltammetry. The apparent surface electron transfer rate constant (K_s) and charge transfer coefficient (α) of the CHIT-Fc/MWCNTs/GCE were also determined by cyclic voltammetry, which were about 1.93 cm s⁻¹ and 0.42, respectively. The sensor displayed good electrocatalytic activity towards the oxidation of sulfite. The peak potential for the oxidation of sulfite was lowered by at least 330 mV compared with that obtained at CHIT/MWCNTs/GCE. In optimal conditions, linear range spans the concentration of sulfite from 5 μM to 1.5 mM and the detection limit was 2.8 μM at a signal-to-noise ratio of 3. The proposed method was used for the determination of sulfite in boiler water. In addition, the sensor has good stability and reproducibility.     

Sensitive determination of hydrazine using poly(phenolphthalein), Au nanoparticles and multiwalled carbon nanotubes modified glassy carbon electrode

This study reports a detailed analysis of an electrode material containing poly(phenolphthalein), carbon nanotubes and gold nanoparticles which shows superior catalytic effect towards to hydrazine oxidation in Britton–Robinson buffer (pH 10.0). Glassy carbon electrode was modified by electropolymerization of phenolphthalein (PP) monomer (poly(PP)/GCE) and the multiwalled carbon nanotubes (MWCNTs) was dropped on the surface. This modified surface was electrodeposited with gold nanoparticles (AuNPs/CNT/poly(PP)/GCE). The fabricated electrode was analysed the determination of hydrazine using cyclic voltammetry, linear sweep voltammetry and amperometry. The peak potential of hydrazine oxidation on bare GCE, poly(PP)/GCE, CNT/GCE, CNT/poly(PP)/GCE, and AuNPs/CNT/poly(PP)/GCE were observed at 596 mV, 342 mV, 320 mV, 313 mV, and 27 mV, respectively. A shift in the overpotential to more negative direction and an enhancement in the peak current indicated that the AuNPs/CNT/poly(PP)/GC electrode presented an efficient electrocatalytic activity toward oxidation of hydrazine. Modified electrodes were characterized with High-resolution transmission electron microscopy (HRTEM), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and electrochemical impedance spectroscopy (EIS). Amperometric current responses in the low hydrazine concentration range of 0.25–13 µM at the AuNPs/CNT/poly(PP)/GCE. The limit of detection (LOD) value was obtained to be 0.083 µM. A modified electrode was applied to naturel samples for hydrazine determination.     

Electroanalytical method for determination of shikonin based on the enhancement effect of cyclodextrin functionalized carbon nanotubes

A simple and sensitive electroanalytical method for determination of shikonin,a widely used antitumoral agent,using β-cyclodextrin-functionalized multiwalled carbon nanotubes composite modified glassy carbon electrodes(MWCNTs/β-CD/GCE) was presented.CDs are water-soluble and environmentally friendly and can improve the dispersibility of MWCNTs/β-CD functional materials,which was confirmed by SEM.The electrochemical behaviors of shikonin on different electrodes were investigated by cyclic voltammetry(CV) and differential pulse voltammograms(DPVs).The results demonstrated that the redox peak currents of shikonin obtained at MWCNTs/β-CD/GCE were much higher than those at theβ-CD/GCE and MWCNTs/GCE,which can be attributed to the combination of the excellent electrocatalytic properties of MWCNTs and the molecular recognition ability of β-CD.At MWCNTs/β-CD/GCE,the response current exhibits a linear range from 5.0 nmol/L to 10.0 μmol/L with a detection limit of 1.0 nmol/L(S/N = 3).As a practical application,the proposed method was applied to quantitatively determine shikoninin urine samples with satisfying results.     

Electrochemical behavior and voltammetric determination of norfloxacin at glassy carbon electrode modified with multi walled carbon nanotubes/Nafion

A simple and rapid electrochemical method is developed for the determination of trace-level norfloxacin, based on the excellent properties of multi-walled carbon nanotubes (MWCNTs). The MWCNTs/Nafion film-coated glassy carbon electrode (GCE) is constructed and the electrochemical behavior of norfloxacin at the electrode is investigated in detail. The results indicate that MWCNTs modified glassy carbon electrode exhibited efficiently electrocatalytic oxidation for norfloxacin (NFX) with relatively high sensitivity, stability and life time. Under conditions of cyclic voltammetry, the current for oxidation of selected analyte is enhanced significantly in comparison to the bare GCE. The electrocatalytic behavior is further exploited as a sensitive detection scheme for the analyte determinations by linear sweep voltammetry (LSV). Under optimized condition in voltammetric method the concentration calibration range and detection limit (S/N=3) are 0.1-100 micromol/L and 5 x 10(-8)mol/L for NFX. The proposed method was successfully applied to NFX determination in tablets. The analytical performance of this sensor has been evaluated for detection of the analyte in urine as a real sample.     

苦参碱在多壁碳纳米管修饰玻碳电极上的电催化氧化及其电分析方法

研究了苦参碱(Matrine, MT) 在多壁碳纳米管修饰玻碳电极(MWCNT/GCE)上的电化学行为. 与GCE相比, MT在MWCNT/GCE上峰电位负移120 mV, 峰电流增大约2.5倍, 表明MWCNT/GCE对MT的电化学氧化具有良好的催化作用. 同时测定并计算了MT在MWCNT/GCE上的电极过程动力学参数: 电子转移系数α、电极反应速率常数ks、扩散系数D. 运用差分脉冲伏安法对苦参碱样品含量进行测定, 相对标准偏差为0.12%～2.9%, 加标回收率为98.4%～99.0%. 该方法可用于MT的电化学定量测定.     

Efficient Direct‐Methanol Fuel Cell Based on Graphene Quantum Dots/Multi‐walled Carbon Nanotubes Composite

Direct‐methanol fuel cells are proton‐exchange fuel cell in which methanol is used as the fuel. The important advantage of these fuel cells is the simplicity of transport and storage of methanol. In this study, methanol fuel cell electrocatalysts including graphene quantum dots (GQDs), functionalized multi‐walled carbon nanotubes (f‐MWCNTs) and GQDs/f‐MWCNTs composite were synthesized. The structures of synthesized electrocatalysts were highlighted by scanning electron microscope (SEM), raman spectroscopy, UV–vis spectroscopy, fourier transform infrared spectroscopy (FTIR), electrochemical impedance spectroscopy (EIS) and x‐ray diffraction (XRD) method. After that, the effective surface areas (ESA) of GQDs, f‐MWCNTs and GQDs/f‐MWCNTs were calculated. Finally, GQDs/f‐MWCNTs composite modified glassy carbon electrode (GQDs/f‐MWCNTs/GCE) showed highest current signals for methanol oxidation than those of comparable GQDs/GCE and f‐MWCNTs/GCE.     

A Hafnium Oxide Based Voltammetric Platform for the Sensitive Determination of Octopamine

An electrochemical sensor was constructed by modification of a glassy carbon electrode (GCE) with nanoparticles of hafnium oxide (HfO₂) and multi-walled carbon nanotubes (MWCNTs) for the sensitive determination of octopamine. The platform (HfO₂NPs/MWCNTs/GCE) presented an improved anodic peak for octopamine at 0.65 V. The combination of HfO₂ and MWCNTs resulted in outstanding catalytic activity and enhanced the magnitude of the peak response. Results suggest that a three-electron oxidation occurs for the process of octopamine. Voltammetry of octopamine exhibited a dynamic linear response in the concentration range of 1.6×10⁻⁶∼4.8×10⁻⁵ M with a detection limit of 5.4×10⁻⁷ M for octopamine.     

Electroanalysis of Bisphenol A at a Multiwalled Carbon Nanotubes‐gold Nanoparticles Modified Glassy Carbon Electrode

A sensitive electrochemical method was developed for the determination of bisphenol A (BPA) at a glassy carbon electrode (GCE) modified with a multiwalled carbon nanotubes (MWCNTs)‐gold nanoparticles (GNPs) hybrid film, which was prepared based on the electrostatic interaction between positively charged cetyltrimethylammonium bromide (CTAB) and negatively charged MWCNTs and GNPs. The MWCNT‐GNPs/GCE exhibited an enhanced electroactivity for BPA oxidation versus unmodified GCE and MWCNTs/GCE. The experimental parameters, including the amounts of modified MWCNTs and GNPs, the pH of the supporting electrolyte, scan rate and accumulation time, were examined and optimized. Under the optimal conditions, the differential pulse voltammetric anodic peak current of BPA was linear with the BPA concentration from 2.0×10^?8 to 2×10^?5 mol L^?1, with a limit of detection of 7.5 nmol L^?1. The proposed procedure was applied to determine BPA leached from real plastic samples with satisfactory results.