水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用

本文报道了水热法可控合成二氧化钛纳米晶及其在染料敏化太阳能电池中的应用.选择合适的有机碱胶化剂,能很好地控制二氧化钛纳米晶的生长,形成不同形貌和粒径的锐钛矿型二氧化钛纳米晶颗粒.染料敏化太阳能电池光电性能测试结果表明,以四乙基氢氧化铵为胶化剂合成的边长为8～13nm的正方形二氧化钛纳米晶构成的光阳极光电性能优于以四丁基氢氧化铵为胶化剂合成的边长为7～10nm的正方形二氧化钛纳米晶以及长18～35nm,宽10～18nm的长方形二氧化钛纳米晶构成的光阳极.用较高浓度的四甲基氢氧化铵胶化剂能合成球形或椭球形亚微米级二氧化钛颗粒,以其为散射中心在光阳极中构建散射层,染料敏化太阳能电池的光电转换效率能由6.77%提高到8.18%.     

二氧化钛纳米管阵列薄膜的超声辐射阳极氧化制备

通过使用铂片作为对电极在含有氢氟酸的二甲基亚砜溶液中, 将金属钛片进行阳极氧化的方法制备得到二氧化钛纳米管阵列薄膜. 在施加40 V偏压超声辐射作用下阳极氧化24 h条件下得到的二氧化钛纳米管长达到680 nm, 管内直径25 nm, 管壁厚度约3～5 nm. 采用了XRD和TEM等分析手段表征了二氧化钛纳米管阵列薄膜的微观结构和表面形貌, 分别测试了薄膜的光吸收性能、循环伏安特性和光化学转换效率, 并和碱性溶胶-凝胶方法制备的纳米晶二氧化钛薄膜作了对比研究. 实验制备的二氧化钛纳米管阵列薄膜电极的光吸收率比纳米晶二氧化钛薄膜提高了40%, 光电化学转换效率前者是后者的6倍, 实验结果表明二氧化钛纳米管阵列薄膜结构有利于加快电子的传输, 并能减少电荷复合, 采用这种二氧化钛纳米管阵列薄膜结构的染料敏化太阳能电池光电极有望进一步提高太阳能电池的效率. 本文还探讨了在超声波辐射作用下二氧化钛纳米管阵列薄膜的形成机理.     

纳米结构ZnO/染料/聚吡咯光阳极的光电化学性质

用光电化学方法研究了染料RuL2 (NCS) 2 (L =2 ,2′ bipydine 4,4′ dicarboxylicacid) (简写为Dye)、聚吡咯 (PPy)敏化氧化锌 (ZnO)纳米晶电极以及用RuL2 (NCS) 2 和PPy复合敏化ZnO纳米晶膜电极的光电化学行为 .实验表明 ,ZnO/PPy纳米多孔膜电极为双层n 型半导体结构 .PPy和RuL2(NCS) 2 都可对ZnO纳米晶膜产生敏化作用 ,ZnO/RuL2 (NCS) 2 /PPy复合多孔膜电极产生的光电流远大于ZnO/PPy纳米多孔膜电极和ZnO/Dye多孔膜电极产生的光电流 .讨论了该电极的光生电子的机理 ,初步测定了ZnO/RuL2 (NCS) 2 /PPy电极作为光阳极的光电化学电池的工作特性曲线 ,测得该电池的光电转换效率为 1 .3% ,填充因子为 0 .75 .     

交流阻抗法研究四羧基酞菁锌掺杂的二氧化钛半导体电极

用电沉积和丝网印刷法制备了纳米二氧化钛膜电极及四羧基酞菁锌(ZnPcTc)掺杂的多孔纳米二氧化钛半导体电极. 采用交流阻抗法(EIS)对二氧化钛膜的电子传输性能以及界面性质进行了表征, 确定了各阻抗弧对应的电极过程. 采用合理的模型计算了电极的电子传输动力学参数. 结果表明, 掺杂ZnPcTc后, 膜电阻明显降低, 且电极-电解液界面电容有所增大, 有利于TiO2电极在染料敏化太阳能电池器件中的应用.     

TiO2薄膜优化对染料敏化太阳电池性能的影响

纳米TiO2多孔薄膜微结构对染料敏化太阳电池(DSC)光伏性能有很大的影响。本文采用不同实验和测试方法研究和分析了溶胶-凝胶法制备纳米TiO2颗粒时的热处理温度、TiO2多孔薄膜厚度、纳米TiO2大颗粒光散射、TiCl4溶液处理和电沉积致密TiO2层对纳米多孔薄膜电极和染料敏化太阳电池光伏性能的影响,得到了最佳的优化条件,为纳米TiO2薄膜材料的批量化制作打下了良好基础。     

有序宏孔-介孔TiO_2薄膜的制备及其在染料敏化太阳能电池中的应用

我们使用表面活性剂P123和聚苯乙烯球双模板技术,合成了多级有序的宏孔/介孔TiO2薄膜,并将其与P25多孔薄膜复合形成双层结构的染料敏化太阳能电池光阳极.实验结果表明,宏孔/介孔TiO2薄膜层的引入,有效地提高了光阳极对太阳光的散射以及捕获能力,从而提高了染料敏化太阳能电池的光电转化效率.与使用单一P25光阳极的染料敏化太阳能电池相比,双层TiO2结构的染料敏化太阳能电池所产生的短路光电流密度从7.49上升到了10.65mA/cm2,开路电压也从0.65提高到了0.70V.在太阳光强度为AM1.5时所测得的光电转化效率表明,双层TiO2结构的染料敏化太阳能电池的光电转化效率为5.55%,比单层P25结构的染料敏化太阳能电池的光电转化效率提升了83%.     

基于不同取代基的噻吩-三苯胺染料敏化剂的合成与光伏性能

本文合成了含3种不同取代基的噻吩-三苯胺染料敏化剂(H1,H2和H3),并将其应用于二氧化钛纳米晶染料敏化太阳能电池.系统地研究了3种染料的光物理、电化学和光伏性能.基于H1的染料敏化太阳能电池获得了9.10%的光电转换效率(Voc=0.72V,Jsc=18.03mAcm-2,FF=0.70).     

基于二级结构TiO_2纳米晶光阳极的高效染料敏化太阳能电池

本文报道了一种新型的二级结构TiO2纳米晶(nano-TiO2)光阳极的简单制备方法及其在高效染料敏化太阳能电池中的应用.通过添加适量TiCl4异丙醇溶液到传统nano-TiO2浆料中,可生成微米级nano-TiO2聚集体.该二级结构能有效提高光阳极光谱吸收和散射性能及电子传输和收集效率.基于这种结构光阳极的染料敏化太阳能电池光电性能有显著提高.在光阳极中将6μm厚传统nano-TiO2膜用相同厚度nano-TiO2聚集体替换,电池光电转换效率由5.03%提高到7.30%.进一步增加nano-TiO2聚集体的厚度能制备出更高光电转换效率的电池.     

基于p型光电极的染料敏化太阳能电池研究进展

基于p型光电极的染料敏化太阳能电池是一种受到广泛关注的新型太阳能电池。根据电池的结构不同可以将其分为p型和p-n叠层型染料敏化太阳能电池。其中p-n型叠层染料敏化太阳能电池的理论光电效率可以达到43%,高于传统的基于n型TiO_2光阳极的染料敏化太阳能电池理论效率(30%),引起了科学界的高度关注。本文将总结基于p型光电极染料敏化太阳能电池(p型和p-n型叠层器件)的研究成果,重点介绍用于p型和p-n型叠层染料敏化太阳能电池的电极材料,染料及电解质的研究进展;同时总结目前该类电池发展中亟需解决的问题以及进一步提高器件效率的途径。     

光电化学水氧化用多孔单晶金红石TiO2纳米棒阵列光阳极的设计和构建

光电化学电池(如染料敏化太阳能电池、量子点敏化太阳能电池以及光电化学水分解电池)是实现太阳能转化及存储的有效手段之一.其中,光电极是光电化学电池的核心组成部分,它集光吸收、光生电荷输运及转移等决定光转化效率的关键过程于一身,因此构筑高活性半导体光电极以实现高效太阳能转化利用引起研究者广泛关注.多孔TiO2纳米颗粒堆垛薄膜光阳极因具有大的比表面积,可提供更多的染料(量子点)担载和反应活性位点,在光电化学电池中表现出优异活性而被广泛研究.然而, TiO2纳米颗粒间大量存在的晶界对光生电荷有较强的散射作用,降低了光生电荷的收集效率.英国牛津大学Snaith研究小组利用模板辅助水热过程首次获得了(001)晶面占优的多孔单晶锐钛矿TiO2微米颗粒,这种多孔单晶TiO2微米颗粒在具有大比表面积的同时,其单晶结构还能有效去除晶界对电荷的散射作用,因而具有优异的电荷输运特性.利用这种多孔单晶TiO2微米颗粒组建的光阳极用于染料敏化太阳能电池中,展现出优异的太阳能光电转化性能.受该工作启发,各种形貌的多孔单晶TiO2微米颗粒作为光催化剂和光电化学分解水用光阳极材料被广泛研究,并表现出优异活性.在单晶微米颗粒堆垛成的薄膜光电极中,虽然单个单晶微米颗粒中晶界对电荷的散射作用被有效抑制,但是单晶颗粒间的晶界仍然存在并影响光生电荷的收集效率.为了彻底抑制晶界对光生电荷的散射作用,每个单晶颗粒都应该贯穿整个薄膜,例如一维TiO2纳米棒单晶阵列薄膜.虽然一维单晶阵列薄膜能够有效提高光生电荷的收集效率,但相对于多孔薄膜具有较小的比表面积,限制了担载染料(量子点)和反应位点的数量.为了增大TiO2单晶纳米棒阵列薄膜的比表面积,目前主要的手段包括调控纳米棒长径比、表面修饰TiO2纳米颗粒以及二次生长构建TiO2枝晶阵列.本文首次提出通过制备多孔单晶TiO2纳米棒单晶阵列薄膜来获得高比表面积和高光生电荷收集效率的光阳极,提高光电化学电池的效率.在透明导电薄膜(FTO)表面利用水热生长TiO2纳米棒阵列薄膜之前,预先在FTO基体上沉积一层SiO2球密堆模板, TiO2纳米棒单晶阵列在从FTO表面向上生长过程中,会将SiO2球模板包裹进TiO2纳米棒中,再通过碱溶液将SiO2球模板溶解,首次在FTO基体上原位生长出多孔单晶TiO2纳米棒阵列薄膜.将所得多孔单晶金红石TiO2纳米棒阵列薄膜作为光电化学分解水电池光阳极,其光电化学分解水活性相对于实心单晶金红石TiO2纳米棒阵列提高了2.6倍.多孔单晶金红石TiO2纳米棒阵列光阳极性能的提升可归因于：(1)多孔结构赋予多孔单晶金红石TiO2纳米棒阵列薄膜更大的比表面积,可提供更多的反应活性位点;(2)多孔结构能够有效缩短单晶金红石TiO2纳米棒中光生电荷体相输运距离,提高光生电荷的收集效率;(3)多孔结构通过对光多次反射吸收可有效增强光吸收,产生更多光生电荷参与水分解反应;(4)在制备过程中引入Si掺杂,导致多孔单晶金红石TiO2纳米棒带隙扩大了0.1 eV,带隙增大归因于导带位置负移0.1 eV,光生电子具有更强的还原能力,光电流起始电位相应负移约0.1 V.     

Improved charge transport in dye-sensitized solar cells employing viscous non-volatile electrolytes

Dye-sensitized solar cells (DSSCs) employing a viscous non-volatile electrolyte were prepared by utilizing anatase TiO₂ nanorods (synthesized via oriented attachment) as a photoanode material. One promising way to enhance the photovoltaic performance of DSSCs employing viscous electrolytes is to increase ion conductivity by increasing the salt concentration. This is accompanied by an acceleration of the charge recombination reaction and the limiting of the overall conversion efficiency. The results showed that a TiO₂ nanorod electrode enables more favorable electron transport than a conventional nanoparticle-based electrode due to the improved electron diffusion length and the large intrinsic surface area.     

Enhanced photovoltaic characterization and charge transport of TIO2 nanoparticles/nanotubes composite photoanode based on indigo carmine dye-sensitized solar cells

Dye-sensitized solar cells (DSSCs) have established themselves as an alternative to conventional solar cells owing to their remarkably high power conversion efficiency, longtime stability and low-cost production. DSSCs composed of a dyed oxide semiconductor photoanode, a redox electrolyte and a counter electrode. In these devices, conversion efficiency is achieved by ultra-fast injection of an electron from a photo excited dye into the conduction band of metal oxide followed by subsequent dye regeneration and holes transportation to the counter electrode. The energy conversion efficiency of DSSC is to be dependent on the morphology and structure of the dye adsorbed metal oxide photoanode. Worldwide considerable efforts of DSSCs have been invested in morphology control of photoanode film, synthesis of stable optical sensitizers and improved ionic conductivity electrolytes. In the present investigation, a new composite nano structured photoanodes were prepared using TiO₂ nano tubes (TNTs) with TiO₂ nano particles (TNPs). TNPs were synthesized by sol–gel method and TNTs were prepared through an alkali hydrothermal transformation. Working photoanodes were prepared using five pastes of TNTs concentrations of 0, 10, 50, 90, and 100 % with TNPs. The DSSCs were fabricated using Indigo carmine dye as photo sensitizer and PMII (1-propyl-3-methylimmidazolium iodide) ionic liquid as electrolyte. The counter electrode was prepared using Copper sulfide. The structure and morphology of TNPs and TNTs were characterized by X-ray diffraction and electron microscopes (TEM and SEM). The photocurrent efficiency is measured using a solar simulator (100 mW/cm²). The prepared composite TNTs/TNPs photoanode could significantly improve the efficiency of dye-sensitized solar cells owing to its synergic effects, i.e. effective dye adsorption mainly originated from TiO₂ nanoparticles and rapid electron transport in one-dimensional TiO₂ nanotubes. The results of the present investigation suggested that the DSSC based on 10 % TNTs/TNPs showed better photovoltaic performance than cell made pure TiO₂ nanoparticles. The highest energy-conversion efficiency of 2.80 % is achieved by composite TNTs (10 %)/TNPs film, which is 68 % higher than that pure TNPs film and far larger than that formed by bare TNTs film (94 %). The charge transport and charge recombination behaviors of DSSCs were investigated by electrochemical impedance spectra and the results showed that composite TNTs/TNPs film-based cell possessed the lowest transfer resistances and the longest electron lifetime. Hence, it could be concluded that the composite TNTs/TNPs photoanodes facilitate the charge transport and enhancing the efficiencies of DSSCs.     

Pechini based titanium sol as a matrix in TiO<Subscript>2</Subscript> pastes for dye-sensitized solar cell application

The influence that the degree of polyesterification has on a titanium sol (Ti-sol) prepared via the Pechini method that acts as a matrix in TiO₂ pastes used for dye sensitized solar cells is reported. The different content of the polyester in the Ti-sol was realized by varying the heating time of the Ti-sol. Titanium dioxide pastes were prepared by introducing a commercial TiO₂ nanopowder into the Ti-sols. The TiO₂ layers were tested as photoanodes in dye-sensitized solar cells (DSSCs). The most appropriate degree of polyesterification was achieved by heating the Ti-sol for 0.5 and 1 h, while longer heating deteriorates the TiO₂ layer morphology. The highest efficiency of the DSSCs based on an ionic liquid electrolyte was 6.3% measured under standard test conditions (100 mW/cm², AM 1.5, 25 °C).     

Multifunctional Ag‐Decorated Porous TiO2 Nanofibers in Dye‐Sensitized Solar Cells: Efficient Light Harvesting,Light Scattering,and Electrolyte Contact

Designing the photoanode structure in dye‐sensitized solar cells (DSSCs) is vital to realizing enhanced power conversion efficiency (PCE). Herein, novel multifunctional silver‐decorated porous titanium dioxide nanofibers (Ag/pTiO₂ NFs) made by simple electrospinning, etching, and chemical reduction processes are introduced. The Ag/pTiO₂ NFs with a high surface area of 163 m² g^?1 provided sufficient dye adsorption for light harvesting. Moreover, the approximately 200 nm diameter and rough surface of the Ag/pTiO₂ NFs offered enough light scattering, and the enlarged interpores among the NFs in the photoanode also permitted electrolyte circulation. Ag nanoparticles (NPs) were well dispersed on the surface of the TiO₂ NFs, which prevented aggregation of the Ag NPs after calcination. Furthermore, a localized surface plasmon resonance effect by the Ag NPs served to increase the light absorption at visible wavelengths. The surface area and amount of Ag NPs was optimized. The PCE of pTiO₂ NF‐based DSSCs was 27 % higher (from 6.2 to 7.9 %) than for pure TiO₂ NFs, whereas the PCE of Ag/pTiO₂ NF‐based DSSCs increased by about 12 % (from 7.9 to 8.8 %). Thus, the PCE of the multifunctional pTiO₂ NFs was improved by 42 %, that is, from 6.2 to 8.8 %.     

Rapid Synthesis of Mesoporous TiO2 for the Photoanodes in Dye Sensitized Solar Cells

Mesoporous TiO₂ microspheres with high specific surface areas were synthesized by means of a facile one‐step microwave hydrothermal process without using any template. The mesoporous materials were rapidly achieved using TiCl₄, urea and ammonium sulphate at comparatively low microwave power (400 W) for 8 min irradiation. The morphology and microstructure of the as‐prepared products were characterized by field emission scanning electron microscopy (FESEM), X‐ray diffraction (XRD), transmission electron microscopy (TEM) and Brunauer‐Emmett‐Teller (BET) surface area analysis. Structural characterization indicates that the TiO₂ microspheres display mesoporous structure. The average pore sizes and BET surface areas of the spheres were 5.3 nm and 222 m²g^?1, respectively. The mesoporous nanocrystals synthesized at 160 °C for 8 min were then used to prepare the photoanode for dye sensitized solar cells (DSSCs). A high power conversion efficiency of 5.72% was achieved from the mesoporous TiO₂ based photoanode, representing about 25.7% improvement over the efficiency of P25 photoanode.     

Effect of pore size/distribution in TiO2 films on agarose gel electrolyte-based dye-sensitized solar cells

This study develops a simple method to change the distribution of the pore size in a TiO₂ layer, using polyethylene glycol (PEG), while maintaining nearly the same surface area and porosity to clarify how large pores affect the performance of dye-sensitized solar cells (DSSCs). Specifically, a heating step at 100 °C for a specific duration is added prior to PEG removal and TiO₂ sintering at 400 °C. This process transforms the role of the PEG from a surfactant to a pore generator (porogen) and forms larger pores, depending on the loading and aggregation time for the PEG to gain larger pores. The effect of larger pores in TiO₂ films under 30 % PEG loading, on the performance of an agarose gel electrolyte-based DSSC, was further investigated using the ionic liquid, 1-allyl-3-ethylimidazolium iodide (AEII). The I–V characteristic and the electrochemical impedance spectroscopy analysis show that larger pores readily improve redox couple diffusion in a TiO₂ porous electrode and modify the interface between electrolyte and TiO₂. Using the optimized TiO₂ film with larger pores (30 % PEG loading, 100 °C/60 min), an efficiency of 7.43 % is achieved for the agarose gel electrolyte-based DSSC, which represents a 26.1 % improvement over TiO₂ without the addition of PEG.     

Effect of TiCl4‐based TiO2 compact and blocking layers on efficiency of dye‐sensitized solar cells

The effect of the number and arrangement of TiO₂‐based photoanode layers on the efficiency of dye‐sensitized solar cells (DSSCs) was investigated. Compact, mesoporous, and blocking layers of TiO₂ were prepared to form monolayer, bilayer, and trilayer photoanodes. Compact and blocking TiO₂ layers were prepared using dip‐coating technique, whereas the doctor‐blade method was employed to prepare TiO₂ paste layers using nanoparticles prepared by the sol–gel method. The crystalline structure of photoanodes was characterized by X‐ray diffraction (XRD) measurements and their morphology and thickness were characterized by the scanning electron microscopy (SEM) technique. The photovoltaic performance of constructed DSSC devices was investigated and the optimum arrangement was identified and explained in terms of dye loading enhancement and recombination reduction at the fluorine‐doped tin oxide (FTO)/electrolyte interface.     

Structurally Stabilized Organosilane‐Templated Thermostable Mesoporous Titania

Structurally thermostable mesoporous anatase TiO₂ (m‐TiO₂) nanoparticles, uniquely decorated with atomically dispersed SiO₂, is reported for the first time. The inorganic Si portion of the novel organosilane template, used as a mesopores‐directing agent, is found to be incorporated in the pore walls of the titania aggregates, mainly as isolated sites. This is evident by transmission electron microscopy and high‐angle annular dark field scanning transmission electron microscopy, combined with electron dispersive X‐ray spectroscopy. This type of unique structure provides exceptional stability to this new material against thermal collapse of the mesoporous structure, which is reflected in its high surface area (the highest known for anatase titania), even after high‐temperature (550 °C) calcination. Control of crystallite size, pore diameter, and surface area is achieved by varying the molar ratios of the titanium precursor and the template during synthesis. These mesoporous materials retain their porosity and high surface area after template removal and further NaOH/HCl treatment to remove silica. We investigate their performance for dye‐sensitized solar cells (DSSCs) with bilayer TiO₂ electrodes, which are prepared by applying a coating of m‐TiO₂ onto a commercial titania (P25) film. The high surface area of the upper mesoporous layer in the P25–m‐TiO₂ DSSC significantly increases the dye loading ability of the photoanode. The photocurrent and fill factor for the DSSC with the bilayer TiO₂ electrode are greatly improved. The large increase in photocurrent current (ca. 56 %) in the P25–m‐TiO₂ DSSC is believed to play a significant role in achieving a remarkable increase in the photovoltaic efficiency (60 %) of the device, compared to DSSCs with a monolayer of P25 as the electrode.     

Preparation of large-area dye-sensitized solar cells based on hydrothermally synthesized nitrogen-doped TiO2 powders

Low-cost, yellowish, nanocrystalline nitrogen-doped titanium dioxide (N-doped TiO₂) powder was synthesized by a hydrothermal method. The as-prepared N-doped TiO₂ powder was characterized by X-ray diffraction, transmission electron microscopy (TEM), UV–Vis absorption spectra, X-ray photoelectron spectroscopy (XPS), and Brunauer–Emmett–Teller analysis techniques. The grain size of the prepared powder was around 13 nm as estimated by both Scherrer’s method and TEM images. The effect of the ratio of N-doped TiO₂ particles to Degussa P25 on the photovoltaic performance of large-area dye-sensitized solar cells (DSSCs) was also investigated. The N-doped TiO₂ electrode showed higher photovoltaic performance compared with that of pure P25 at constant irradiation of 100 mW cm^?2, which is attributed to the large pore size and high surface area of N-doped TiO₂ resulting in the introduction of extra charge carrier pathways that could be beneficial for overall charge transportation. Energy conversion efficiency of 5.12 % was achieved in a DSSC device with active area of 51.19 cm².     

Fabrication of highly efficient dye-sensitized solar cell and CO2 reduction photocatalyst using TiO2 nanoparticles prepared by spin coating-assisted sol–gel method

A sol?Cgel method was applied for fabrication of nanocrystalline anatase TiO₂ thin films on ITO glass substrates and followed by rapid thermal annealing for application as the work electrode for dye-sensitized solar cells (DSSC). TiO₂ nanoparticles were characterized by X-ray diffraction (XRD) pattern and scanning electron microscopy (SEM) and the absorption of dye on the TiO₂ electrode was shown by UV?Cvis spectroscopy. By controlling different parameters including numbers of coated layers, the gap between two electrodes, sensitization time, and light source power, TiO₂-based solar cells with high efficiency was achieved. The results show that a five time spin-coated TiO₂ electrode with applying sealant and sensitization time of 24?h in N3 dye under illumination of 100?W?cm^?2 tungsten lamp give the optimum power conversion efficiency (??) of 6.61%. The increases in thickness of TiO₂ films by increasing the numbers of coated layers can improve adsorption of the N3 dye through TiO₂ layers to increase the open-circuit voltage (V _oc). However, short-circuit photocurrents (J _sc) of DSSCs with a one-coated layer of TiO₂ films are smaller than those of DSSCs with five-coated layer of TiO₂ films. It could be due to the fact that the increased thickness of TiO₂ thin films also resulted in a decrease in the transmittance of TiO₂ thin films. Also, this electrode was employed to photoreduce CO₂ with H₂O under tungsten lamp as light source.