以碳微球为核的金纳米壳球体的制备

通过水热合成法制备了单分散碳微球, 并以此单分散碳微球为核, 利用其表面修饰的银纳米粒子作为种子, 进一步还原制备了以碳微球为核、以金为壳的金纳米壳(Nanoshell)球体. 通过透射电子显微镜和紫外可见吸收光谱对其形态以及光谱性质进行了表征. 研究结果表明, 采用该种方法制备出来的碳微球具有良好的单分散性, 表面修饰简便快捷, 利用碳微球为核制备的金纳米壳球体尺寸可控, 在近红外范围内有强吸收. 实验结果证明该方法是制备金纳米壳球体的一种有效新方法.     

单分散SnO2中空微纳米球的制备和性质

模板法是制备无机中空微纳米球的重要方法之一. 本文以苯乙烯为单体, 通过乳液聚合得到粒径约为620 nm的单分散聚苯乙烯(PS)微球. 以磺化后的聚苯乙烯(PSS)微球为模板, 利用阴阳离子静电吸附作用, 将PSS与前驱体SnSO₄中的Sn²⁺结合. 通过Sn²⁺在乙醇-水介质中的水解作用得到核-壳复合结构, 再经高温煅烧, 得到SnO₂中空微纳米球. 实验对前驱体的浓度、表面活性剂的用量、反应时间及模板选择等方面做了研究,通过扫描电镜(SEM)、X 射线衍射(XRD)、红外(IR) 光谱、热重分析(TGA)、H₂ 程序升温还原(H₂-TPR)、Brunauer-Emmett-Teller (BET)比表面积等技术深入探究SnO₂中空微纳米球的结构, 并对比中空SnO₂与实心粒子的氧化还原特性. BET和H₂-TPR显示将SnO₂制备成微纳米空心球后其比表面积增大, 表面氧空位明显增多, 氧化活性明显提高. 从IR 及XRD推断核-壳结构形成机理, 进而优化出简单合理的实验方案, 获得表面光滑、结构致密, 包覆厚度可控的SnO₂中空微纳米球.     

Au@SiO_2中空微球的制备及催化性能

以天然高分子阿拉伯树胶(AG)为还原剂和稳定剂制备了金纳米粒子;将含有金纳米粒子(Au NPs)、阿拉伯树胶和氨水的溶液滴加到乙醇中形成AG-Au NPs复合胶团;利用正硅酸乙酯水解,在AG-Au NPs表面包覆二氧化硅壳层;通过简单水洗的方法得到了金纳米粒子@二氧化硅(Au@SiO_2)中空微球.采用透射电子显微镜(TEM)、X射线衍射仪(XRD)和氮气吸附实验等对Au@SiO_2中空微球进行表征.通过设计对比实验,证实阿拉伯树胶在中空结构形成过程中起到模板剂的作用.催化性能测试结果表明,所制备的Au@SiO_2中空微球在硼氢化钠还原亚甲基蓝的反应中表现出良好的催化活性和重复使用性.     

制备方法对模板法制备SiO_2中空微球形貌的影响

模板法是制备无机中空微球的重要方法之一.首先通过苯乙烯和甲基丙烯酸的无皂乳液聚合法制得表面含羧基、粒径为360nm的单分散聚苯乙烯(PSt)乳胶粒,并以此为模板,分别采用表面改性-前驱体水解法(PHC)和SiO2纳米颗粒层层自组装法(LBL),制备出了不同壳层厚度的PSt/SiO2核壳结构复合微球,然后经500℃煅烧4h,得到SiO2中空微球.利用透射电镜和扫描电镜对微球结构形态进行了表征.研究表明,首先利用γ-氨丙基三乙氧基硅烷(KH-550)对PSt模板微球进行表面改性、然后再在乙醇-水混合介质中进行原硅酸乙酯(TEOS)水解与缩合反应的PHC法,是制备PSt/SiO2核壳结构复合微球的简便方法,复合微球经煅烧可制得表面均匀、结构致密、壳层厚度和形貌可控的SiO2中空微球;而LBL法制备PSt/SiO2核壳结构复合微球的工艺复杂,煅烧后所得SiO2中空微球结构疏松,易于破碎.     

中空SiO_2纳米微球的制备与表征

在乙醇/氨水介质中,将SiO2包覆在聚乙烯吡咯烷酮(PVP)功能化的聚苯乙烯(PS)微粒表面,利用一步法得到了中空纳米二氧化硅微球;研究了影响中空纳米二氧化硅微球形成的主要因素,并探讨了中空纳米SiO2微球的可能形成机理.结果表明,在一定的反应时间下,当氨水用量为0.6 mL、温度为70℃时,可以获得空心结构的SiO2纳米微球;通过控制四乙基原硅酸盐(TEOS)的量可以调节微球的包覆层厚度.     

结合表面引发的原子转移自由基聚合和气/固反应制备CdS纳米微粒/聚苯乙烯核壳微球

结合表面引发的原子转移自由基聚合和气/固反应制备CdS纳米微粒/聚苯乙烯核壳微球. 以表面富含环氧基团的聚苯乙烯微球为基底, 利用开环反应在水相中一步接枝表面引发剂, 然后在聚苯乙烯微球表面引发甲基丙烯酸镉的原子转移自由基聚合, 最后通入H2S气体原位生成CdS纳米微粒. 生成的CdS纳米微粒复合的核壳微球呈草莓状形貌, 且具有良好的光学性能.     

交联聚膦腈中空微球的可控制备

以分散聚合法制备的聚苯乙烯微球为模板,以六氯环三膦腈、4,4’-二羟基二苯砜为共聚单体,三乙胺为缚酸剂,室温条件下制备出了聚苯乙烯／聚膦腈（核／壳）复合微球,然后用四氢呋喃处理该复合微球,得到聚膦腈中空微球。利用红外光谱、元素分析、扫描电镜及投射电镜对所制备中空微球的结构及形貌进行了表征。结果表明,所制备聚膦腈中空微球...     

多金核二氧化铈空心球用于硝基苯酚催化加氢（英文）

催化剂的微观结构在催化还原反应、有机物氧化反应及有机物转化反应中起着关键作用.本文利用无模板方法合成了多金核中空二氧化铈微球催化剂.将制备好的二氧化铈中空微球浸渍到一定浓度的氯金酸溶液中,然后多次洗涤除去表面吸附的氯金酸离子,最后通过硼氢化钠还原制成中空氧化铈微球包覆的多金核的核壳结构催化剂.将该核壳结构材料用于硝基苯酚加氢反应与金纳米粒子及氧化铈微球相比,多金核中空二氧化铈核壳结构表现出优越的活性和稳定性.通过这种浸渍洗涤再还原的简单方法合成的多金核二氧化铈催化剂有望应用于生物医药和能源环境等领域.     

侧链偶氮聚电解质在胶体微球表面的静电层层自组装和微胶囊制作

将侧链偶氮聚电解质应用于聚苯乙烯胶体微球表面的静电层层自组装,得到了偶氮聚电解质和聚二烯丙基二甲基氯化铵多层膜覆盖的核壳微球.实验表明,组装后偶氮苯基团发生了一定程度的解聚集,得到的胶体微球可表现出明显的光色效应.研究进一步采用含肉桂酸酯的光敏聚电解质作为交联的保护壳层,并通过光交联反应使表面层发生交联固化反应.将上述具有核壳结构的胶体球溶解去除聚苯乙烯内核后,得到了含光响应聚电解质的空心微胶囊.     

磁性Fe_3O_4-聚吡咯纳米微球的合成与表征

报道了具有核壳结构的Fe3O4 聚吡咯磁性纳米微球的合成方法和表征结果 .微球同时具有导电性和磁性能 .在优化的实验条件下 ,可得到饱和磁化强度为 2 3 4emu g ,矫顽力为 45 2Oe的磁性微球 .微球的导电性随着微球中Fe3O4含量的增加而下降 .微球的磁性能则随着Fe3O4含量的增加而增大 .Fe3O4磁流体的粒径和磁性聚吡咯微球的粒径均在纳米量级 .纳米Fe3O4粒子能够提高复合物的热性能 .实验表明 ,磁流体和聚吡咯之间存在着一定的相互作用 ,正是这种相互作用使磁性聚吡咯纳米微球的热稳定性提高 .     

Preparation of SiO2@polystyrene@polypyrrole sandwich composites and hollow polypyrrole capsules with movable SiO2 spheres inside

In this paper, we describe a flexible method for preparing conducting building blocks: SiO2@polystyrene@polypyrrole sandwich multilayer composites and hollow polypyrrole (PPy) capsules with movable SiO2 spheres inside. First, SiO2@polystyrene (PS) core/shell composites were synthesized, and then SiO2@PS@PPy sandwich multilayer composites were prepared by chemical polymerization of pyrrole monomer on the surface of SiO2@PS composites. Furthermore, hollow polypyrrole capsules with movable SiO2 spheres inside were obtained after removal of the middle PS layer. The diameter of sandwich multilayer composites could easily be controlled by adjusting the dosage of pyrrole monomer. The conductivities of composites increased with the increase of PPy content. After the insulating PS layer was selectively etched, the conductivities of hollow capsules with movable SiO2 spheres inside were much higher than those of the corresponding sandwich multilayer composites.     

单分散核／壳结构导电高分子复合材料的研究（Ⅰ）——单分散核／壳结构聚苯乙烯／聚吡咯的结构表征

导电高分子在光、电、磁等领域表现出的广泛应用前景 ,使它成为材料科学的研究热点 .然而 ,早期发现的导电高分子的不溶不熔性 ,使它在可加工性和机械性能等方面仍面临许多挑战 .核 /壳结构导电高分子与单分散技术的结合 ,无疑为这一领域的研究带来新的生机和活力 .目前仅有的少量文献主要集中报道微米和亚微米级单分散核 /壳导电高分子复合材料的研究 ,大多采用种子乳液聚合法合成 .微米级的种子乳液通常采用以醇为分散介质的分散聚合方法制备 [1～ 3] ,由于种子分散体系要经反复离心分离 ,除去醇类 ,重新分散在水相中再进行核 /壳导电高分…     

Fabrication of spindle Fe(2)O(3)@polypyrrole core/shell particles by surface-modified hematite templating and conversion to spindle polypyrrole capsules and carbon capsules

By using a surface-modified templating method, Fe(2)O(3)@polypyrrole (PPy) core/shell spindles have been successfully prepared in this paper. The Fe(2)O(3) particles with spindle morphology were initially fabricated as core materials. After the PVP modification, the Fe(2)O(3) spindles were subsequently coated with a tunable thickness layer of PPy by in situ deposition of the conducting polymer from aqueous solution. Hollow PPy spindles were produced by dissolution of the Fe(2)O(3) core from the core/shell particles. High-temperature treatment under vacuum condition covert the hollow PPy spindles into carbon capsules by carbonization of the PPy shell. Transmission electron microscope (TEM), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermal gravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS) confirmed the formation of the Fe(2)O(3)@PPy core/shell particles, PPy and carbon capsules with spindle morphology.     

Synthesis and characterization of carbon nanotube/polypyrrole core–shell nanocomposites via in situ inverse microemulsion

We demonstrate here a feasible approach to the preparation of multiwalled carbon nanotube (MWNT)/polypyrrole (PPy) core–shell nanowires by in situ inverse microemulsion. Transmission electron microscopy and scanning electron microscopy showed that the carbon nanotubes were uniformly coated with a PPy layer with a thickness of several to several tens of nanometers, depending on the MWNT content. Fourier transform infrared spectra suggested that there was strong interaction between the π‐bonded surface of the carbon nanotubes and the conjugated structure of the PPy shell layer. The thermal stability and electrical conductivity of the MWNT/PPy composites were examined with thermogravimetric analysis and a conventional four‐probe method. In comparison with pure PPy, the decomposition temperature of the MWNT/PPy (1 wt % MWNT) composites increased from 305 to 335 °C, and the electrical conductivity of the MWNT/PPy (1 wt % MWNT) composites increased by 1 order of magnitude. The current–voltage curves of the MWNT/PPy nanocomposites followed Ohm's law, reflecting the metallic character of the MWNT/PPy nanocomposites. The cyclic voltammetry measurements revealed that PPy/MWNT composites showed an enhancement in the specific charge capacity with respect to that of pure PPy. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 6105–6115, 2005     

超临界二氧化碳流体环境中导电聚吡咯复合材料的制备

以聚苯乙烯(PS)和锌盐中和的磺化聚苯乙烯(Zn-SPS)膜为基体, 在超临界二氧化碳(SC-CO₂)环境中用化学氧化法原位制备了聚吡咯(PPy)导电复合材料. 由于SC-CO₂对聚合物基体的强溶胀作用, 吡咯分子高效地扩散到基体内部进行聚合而形成导电通路, 得到比传统的水溶液法更高的电导率. 聚合物基体的性质对复合材料的导电性和形貌产生重要影响. 在相同条件下, Zn-SPS/PPy的电导率比PS/PPy高3~4个数量级, 而它们的体积逾渗阈值分别为2.7%和6.2%, 远远低于理论预测值(16%).     

Characterization and electrical properties of polypyrrole/multiwalled carbon nanotube composites synthesized by in situ chemical oxidative polymerization

This study describes the preparation of polypyrrole (PPy)/multiwalled carbon nanotube (MWNT) composites by in situ chemical oxidative polymerization. Various ratios of MWNTs, which served as hard templates, were first dispersed in aqueous solutions with the surfactant cetyltrimethylammonium bromide to form micelle/MWNT templates and overcome the difficulty of MWNTs dispersing into insoluble solutions of pyrrole monomer, and PPy was then synthesized via in situ chemical oxidative polymerization on the surface of the templates. Raman spectroscopy, Fourier transform infrared (FTIR), field‐emission scanning electron microscopy (FESEM), and high‐resolution transmission electron microscopy (HRTEM) were used to characterize the structure and morphology of the fabricated composites. Structural analysis using FESEM and HRTEM showed that the PPy/MWNT composites were core (MWNT)–shell (PPy) tubular structures. Raman and FTIR spectra of the composites were almost identical to those of PPy, supporting the idea that MWNTs served as the core in the formation of a coaxial nanostructure for the composites. The conductivities of these PPy/MWNT composites were about 150% higher than those of PPy without MWNTs. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1413–1418, 2006     

Preparation of conductive polypyrrole (PPy) composites under supercritical carbon dioxide conditions

Electrically conductive composites were prepared via the chemical oxidative polymerization of the pyrrole monomer in polystyrene (PS) and zinc neutralized sulfonated polystyrene (Zn-SPS) films under supercritical carbon dioxide (SC-CO₂) conditions. The strong swelling effect of SC-CO₂ made polypyrrole (PPy) particles not only form on the surface, but also become incorporated into the film, resulting in a homogeneous structure with a relatively higher conductivity. By comparison, the composite prepared in aqueous solutions shows a skin-core structure and a conductivity of 3 to 4 orders of magnitude lower than that of the former due to the diffusion-controlled process of the pyrrole monomer. The percolation thresholds of PS/PPy and Zn-SPS/PPy composites were 6.2% and 2.7% of the volume fraction of PPy, respectively, much lower than the theoretically predicted value of 16%. Moreover, the conductive composites prepared under SC-CO₂ conditions showed higher thermal stability, especially in the high-temperature region. Translated from Chemical Journal of Chinese Universities, 2006, 27(4): 771–774 (in Chinese)     

Electrochemically controlled release based on nanoporous conducting polymers

An electrochemically controlled drug release system based on nanoporous polypyrrole (PPy) films was developed. Pyrrole and a model drug, fluorescein, were electrochemically copolymerized on glassy carbon (GC) electrodes modified with self-assembled multilayer polystyrene (PS) nanobeads, and PPy films incorporated with fluorescein as dopants were formed among the interstitial spaces of the tightly packed PS nanobead template. After the removal of the PS hard template, nanoporous PPy films incorporated with the drug fluorescein were obtained. Due to the porous morphology and huge surface area, the efficiency of the prepared PPy films in electrochemically releasing incorporated fluorescein was about nine times higher than that of conventional PPy films.     

Fe3O4/Polypyrrole/Au nanocomposites with core/shell/shell structure: synthesis, characterization, and their electrochemical properties

Uniform Fe3O4 nanospheres with a diameter of 100 nm were rapidly prepared using a microwave solvothermal method. Then Fe304/polypyrrole (PPy) composite nanospheres with well-defined core/shell structures were obtained through chemical oxidative polymerization of pyrrole in the presence of Fe3O4; the average thickness of the coating shell was about 25 nm. Furthermore, by means of electrostatic interactions, plentiful gold nanoparticles with a diameter of 15 nm were assembled on the surface of Fe3O4/PPy to get Fe3O4/PPy/Au core/shell/shell structure. The morphology, structure, and composition of the products were characterized by transmission electronic microscopy (TEM), scanning electronic microscopy (SEM), X-ray powder diffraction (XRD), and Fourier transform infrared (FT-IR) spectroscopy. The resultant nanocomposites not only have the magnetism of Fe3O4 nanoparticles that make the nanocomposites easily controlled by an external magnetic field but also have the good conductivity and excellent electrochemical and catalytic properties of PPy and Au nanoparticles. Furthermore, the nanocomposites showed excellent electrocatalytic activities to biospecies such as ascorbic acid (AA).     

壳层可控导电聚吡咯/聚苯乙烯复合微球及聚吡咯中空微胶囊的制备

在导电聚合物含量较小时,含核壳结构的导电聚合物复合粒子就可以具有和本体相当的导电率,且加工性好,近年来这种核壳结构微粒的制备已引起了科学家们的广泛关注．Armes等[制备了导电聚吡咯、导电聚苯胺包覆聚苯乙烯的核壳结构胶体粒子及聚苯胺和二氧化硅的纳米复合物．刘正平等用改进的方法在粒径为116nm的单分散聚苯乙烯乳胶粒子上包覆聚吡咯,