Fe3O4@SiO2@TiO2复合纳米结构的尺寸与磁性调控

采用共沉淀法和溶剂热法制备了不同尺寸的Fe3O4纳米粒子,通过Stöber法和溶胶-凝胶法在Fe3O4磁核上包覆SiO2和TiO2壳层获得不同尺寸的Fe3O4@SiO2@TiO2复合纳米结构．采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和振动样品磁强计(VSM)等对其结构、形貌和磁性进行了研究．结果表明,大尺寸复合纳米粒子包覆均匀,分散性好,饱和磁化强度较大,有利于TiO2光催化剂的磁回收与再利用．     

Er3+掺杂SiO2复合的Al2O3粉末结构及光致发光特性

采用溶胶-凝胶(sol-gel)工艺制备0.1 mol% Er3+掺杂Al2O3体系和SiO2-Al2O3复合体系粉末. 实验结果表明:5 mol%的SiO2复合加入Al2O3抑制γ→θ和θ→α相转变. 掺0.1 mol%Er3+:Al2O3体系粉末,900℃烧结,在1.47-1.63 μm波段内光致发光(PL)谱为中心波长1.53 μm、半高宽56 nm的单一宽峰,1000-1200℃烧结,劈裂为多峰PL谱. 掺0.1 mol%Er3+:SiO2-Al2O3复合体系粉末,在高达1200℃烧结,仍保持中心波长1.53 μm的单一宽峰PL谱,由于-OH更完全的脱除,PL强度较900℃烧结Al2O3体系,SiO2-Al2O3复合体系均提高1个数量级.     

RuO2/TiO2/漂珠复合光催化剂的制备及性能

"利用RuO2/TiO2前驱体溶胶,采用溶胶-凝胶-浸渍法在漂珠(FP)表面沉积RuO2/TiO2膜,经120 ℃干燥、500 ℃焙烧制备复合光催化剂RuO2/TiO2/FP,并通过SEM、XRD以及FT-IR分别对其结构进行了表征． 结果表明,RuO2/TiO2膜的平均厚度(三层)约1 1m,膜材料中TiO2主要呈现锐钛矿型结构,而RuO2是以非晶态高度分散在粒子表面．以高效氯氰菊酯杀虫剂的光催化降解为模型反应,研究了RuO2/TiO2/FP的光催化性能,探讨了影响催化剂活性的因素及采用太阳光做光源处理     

Fe_3O_4@SiO_2@TiO_2复合纳米结构的尺寸与磁性调控

采用共沉淀法和溶剂热法制备了不同尺寸的Fe_3O_4纳米粒子,通过Stber法和溶胶-凝胶法在Fe_3O_4磁核上包覆SiO_2和Ti O2壳层获得不同尺寸的Fe_3O_4@SiO_2@Ti O2复合纳米结构.采用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和振动样品磁强计(VSM)等对其结构、形貌和磁性进行了研究.结果表明,大尺寸复合纳米粒子包覆均匀,分散性好,饱和磁化强度较大,有利于TiO_2光催化剂的磁回收与再利用.     

铁掺杂TiO2/膨润土光催化剂的制备及表征

以溶胶-凝胶法制备了过渡金属铁掺杂的Fe-TiO2/膨润土复合光催化剂,通过XRD、FTIR技术对该系列催化剂的结构进行了表征,并以亚甲基蓝染料废水为模型,考察了紫外光和日光下铁掺杂量对催化剂性能的影响。结果表明,催化剂中有锐钛矿型TiO2生成,铁掺杂TiO2进入了膨润土的蒙脱石层间,改变了蒙脱石层间的有序性,生成了Ti—O—Si键,实现了TiO2粒子与膨润土的复合;适量Fe3+的掺杂降低了TiO2粒子的粒径,并且部分Fe3+还可能进入了TiO2的晶格,形成了缺陷位,拓宽了TiO2的光谱利用范围,提高了光催化活性。     

TiO_2对α-Fe_2O_3纳米微粒拉曼散射效应的影响

选取α Fe2O3和TiO2研究一种氧化物对另一种氧化物的拉曼散射效应。采用Sol gel方法制备纳米α Fe2O3/TiO2复合微粒,α Fe2O3粒径及含量分别为20nm、150nm和3%、6%、12%。制备过程中调节水解时的pH值和热处理温度,得到掺杂α Fe2O3粒子的不同晶型的TiO2纳米颗粒。Raman测量结果显示,α Fe2O3粒径越小、含量越高,TiO2对其散射效应的影响越大。不同的TiO2晶型对α Fe2O3纳米粒子的拉曼增强效应也不同。锐钛矿型及金红石型TiO2对α Fe2O3有一定的拉曼增强作用,当水解pH值较小时,得到板钛矿型TiO2,由于部分板钛矿型TiO2振动声子模的峰位与α Fe2O3的重叠,所以尚难观察它对α Fe2O3的拉曼增强效应。     

稀土Eu3+掺杂纳米TiO2-SiO2发光材料的制备和发光性质的研究

采用溶胶-凝胶法制备了稀土Eu3+掺杂于不同比例的纳米TiO2-SiO2复合体系,研究了基质中钛、硅摩尔配比对发光性能的影响.样品的FTIR谱图显示:纳米复合氧化物SiO2-TiO2之间发生了键合作用,形成了Ti-O-Si键;TEM显示样品的颗粒大小约为35 nm,是具有一定的单分散性的球形颗粒;XRD和SAED结果表明,样品退火至700℃后仍为单一的锐钛矿相,这说明微量硅的加入对二氧化钛的锐钛矿相有热稳定的作用.当微量的Si4+进入TiO2的晶格,取代部分Ti4+的位置时,形成了结构等电子陷阱.通过对样品的激发光谱、发射光谱分析,发现这种结构有利于将基质吸收的能量传递到发光中心,使Eu3+的465nm处7F0→5D2激发效率最高,成为最灵敏的激发线.     

TiO2 .nH2O凝胶预处理对水热合成SrTiO3粉的影响

以TiCl4为钛源,首先制备TiO2*nH2O凝胶,然后在80℃的水热条件下制备了SrTiO3粉.利用X射线衍射(XRD)、透射电子显微镜(TEM)和红外光谱(FTIR)研究了TiO2*nH2O凝胶水洗方式、阴离子(Cl-和NO3-)以及TiO2*nH2O热处理对SrTiO3粉性能的影响.结果表明,水洗和热处理都能使TiO2*nH2O凝胶产生晶化;TiO2*nH2O的晶化程度对产物SrTiO3颗粒的粒度和粒度分布有很大影响,以非晶质TiO2*nH2O为钛源制备的SrTiO3颗粒粒度大且粒度分布宽.以结晶TiO2*nH2O为钛源制备的SrTiO3颗粒粒度小且粒度分布窄,而且可以得到纳米颗粒.水热反应液相中存在Cl-或NO3-能使产物SrTiO3颗粒粒度稍有增大.综合以上结果,TiO2*nH2O凝胶水洗对产物颗粒的影响主要是由于使凝胶产生了晶化,而由阴离子脱除产生的影响很小.因此,在不考虑阴离子对其它工程化影响(如设备腐蚀等)的前提下,可采用热处理代替水洗.     

CuO/γ-Al2O3催化吸附剂脱硝性能研究

本文采用溶胶-凝胶法制备CuO/γ-Al2O3催化吸附剂颗粒.分析表明:SO2的存在可以提高CuO/γ-Al2O3催化吸附剂的脱硝活性,SO2存在条件下,CuO/γ-Al2O3催化吸附剂的脱硝活性在载铜量8wt%时达到最高,达到95.7%.载铜量太高会使单位质量催化剂NO脱除率降低.在350℃时,硫酸盐化和未硫酸盐化的8wt%Cu催化吸附剂NO脱除率达到最高.NH3/NO摩尔比在1～1.2之间时,CuO/γ-Al2O3催化吸附剂的脱硝活性较高.     

纳米稀土镧8-羟基喹啉间羟基苯甲酸/TiO2的红外及拉曼光谱研究

采用沉淀法/溶胶-凝胶复合方法制备了纳米稀土镧8-羟基喹啉间羟基苯甲酸/TiO2复合粒子。并应用红外和拉曼光谱对其进行了表征。红外光谱证明样品为稀土镧8-羟基喹啉间羟基苯甲酸/TiO2复合粒子。拉曼光谱证明其拉曼峰与文献报道的TiO2拉曼峰相比,部分峰位出现了蓝移,部分峰位出现了红移现象,从纳米粒子的表面结构及配合物层的压力出发对此现象进行了定性解释和讨论。     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.