单畴的单原子In纳米线阵列的制备与研究

利用Si（001）向［110］方向偏4°角的斜切表面作为衬底，成功地制备了分布均匀的单畴的单原子In链阵列.扫描隧道显微镜分析表明，沉积的In原子优先吸附在台面上沿着台阶内边缘的位置，并在两个Si的二聚体链之间形成稳定的In二聚体.In二聚体组成直的单原子链，其生长机理与Car提出的“表面聚合反应”相一致.另外，衬底具有非常窄的台面和双原子层台阶边的特殊结构是形成单畴的单原子链的关键. 关键词： 铟单原子链 硅邻近面 扫描隧道显微镜     

Sb/Si(001)表面的半经验研究

用基于Chadi模型和格林函数方法的一种计算表面应力的半经验方法研究了Sb吸附在Si(001) 衬底上的性质.结果显示,Sb原子在Si(001)表面形成对称的dimer,其键长为0.293nm,表 面以下层的弛豫很小.Sb/Si(001)2×1表面沿着dimer方向的张应力为1.0eV/(1×1cell),而 沿垂直于dimer方向的压应力为-1.1eV/(1×1cell).Sb/Si(001)表面应力的主要贡献来自于 最上面三层表面. 关键词： 表面应力 异质生长 格林函数方法     

磁控溅射CNx薄膜的附着力、粗糙度与衬底偏压的关系

对磁控溅射生长在单晶Si(001)衬底上的CNx薄膜的附着力、粗糙度与衬底偏压的关系进行了研究。CNx薄膜沉积实验在纯N2的环境下进行．衬底温度(Ts)保持在350℃．衬底偏压(Vb)在0～-150V之间变化。利用原子力显微镜(AFM)和划痕试验机来测量CNx薄膜的表面粗糙度及对衬底的附着力。AFM和划痕实验的结果显示衬底偏压Vb对CNx薄膜的附着力和表面粗糙程度的影响很大，在-100V偏压下生长的CNx薄膜表面最光滑(粗糙度最小)，同时对Si(001)衬底的附着力最好。最后根据实验结果确定了在单晶Si(001)衬底上生长光滑而且附着力好的CNx薄膜的最佳实验条件。     

C20与Si(100)-(2×1)重构表面相互作用的计算机模拟研究

用分子动力学的方法模拟研究了低能C20与Si(100)-(2×1)重构表面的相互作用过程.将描述C、Si结构的Tersoff势和描述原子间短程排斥的KrC势相结合,建立了一个混合势作为原子间的相互作用模型.荷能C20垂直轰击到Si(100)-(2×1)表面后,由于在<110>方向受到非对称力场的作用而产生横向的集体运动,改变的入射能量导致C20与Si(100)-(2×1)表面最接近的垂直距离不同,从而受到不同的横向力场的作用而产生不同的表面运动特性.C20能量耗尽后稳定吸附在Si(100)-(2×1)表面,且只有两个稳定吸附位置,即二聚体(dimer)和"峡谷"(trough)位,这两个吸附位置的存在可用C20与Si(100)-(2×1)表面之间非对称的表面力场分布来定性解释.最终C20与Si(100)-(2×1)表面有强烈的化学键形成.模拟结果与STM的实验观察结果进行了比较.     

Si(001)-(2*2*1):H表面O2吸附的密度泛函理论研究

建立了一种计算Si(001)-(2×2×1):H表面O2吸附的理论模型．在周期性边界条件下,采用基于密度泛函理论广义梯度近似的超软赝势法对Si(001)-(2×2×1):H表面O2吸附进行了第一性研究．通过占位能的计算,得到了Si(001)-(2×2×1):H表面O2的最佳吸附位置．计算结果表明吸附后的反应产物应为Si=O和H2O,从理论上支持了D．Kovalev等人提出反应机制．     

β-SiC(001)-(2×1)表面结构的第一性原理研究

利用缀加平面波加局域轨道(APW+LO)的第一性原理方法计算了β-SiC(001)-(2×1)表面的原子及电子结构. 原子结构的计算结果表明，与Si(001)-(2×1) 表面的非对称性Si二聚体模型不同，β-SiC(001)-(2×1)表面为对称性的Si二聚体模型，其二聚体的Si原子间键长也较大，为0.269nm. 电子结构的计算结果表明，在费米能级处有明显的态密度，因此β-SiC(001)-(2×1)表面呈金属性. 在带隙附近存在四个表面态带,其中的两个占有表面态带已由价带的同步辐射光电子能谱实验得到证实. 关键词： 碳化硅 缀加平面波加局域轨道方法 原子结构 电子结构     

SiO2-羟基表面上金属原子的第一性原理研究

采用第一性原理方法研究了SiO2-羟基表面上几种金属原子的吸附性质,发现In和Ga在SiO2-羟基表面上的结合很弱,而Fe,Co,Ni在该表面上与Si,O形成强的化学键.等势能面和扩散势垒计算表明In(Ga)的扩散激活能只有0.1-0.3 eV,表明这两种原子容易在表面上扩散.这些结果可以定性地解释纳米合成中的一些实验现象.     

Ge(112)-(4×1)-In表面重构的原子结构

用扫描隧道显微镜(STM)研究了亚单层In原子引起的Ge(112)-(4×1)-In表面重构.结合随偏压极性不同而显著不同的STM图象和相应的“原子图象”,为这个重构提出了一个原子结构模型,供进一步研究参考.其中,In原子的吸附位置与它在Si(112)表面的吸附位置一致,但与Al原子和Ga原子在Si(112)表面的吸附位置不同.这个吸附位置的不同主要是由In原子较长的共价键键长引起的 关键词： 表面结构 In Ge 扫描隧道显微镜(STM)     

Longitudinal,transverse,density-of-states,and conductivity masses of electrons in（001）,（101） and（111） biaxiallystrained-Si and strained-Si1-xGex

In this study,the electron effective masses,including longitudinal,transverse,density-of-states and conductivity effective masses,have been systematically investigated in(001),(101) and(111) biaxially strained Si and Si1-xGex.It is found that the effect of strain on the longitudinal and transverse masses can be neglected,that the density-of-states masses in(001) and(110) biaxially strained Si and Si1-xGex materials decrease significantly with increasing Ge fraction(x),and that the conductivity masses along typical orientations in(001) and(110) strained Si and Si1-xGex.are obviously different from those in relaxed Si.The quantitative results obtained from this work may provide valuable theoretical references to understanding strained materials physics and studying conduction channel design related to stress and orientations in the strained devices.     

Sr/Si界面沉积SrTiO3初始生长阶段的扫描遂道显微术研究

本文工作利用脉冲激光沉积术(PLD)和超高真空扫描隧道显微术(UHV-STM),研究了在Sr/Si(001)-(2×1)衬底表面上真空室温沉积几个单层SrTiO₃薄膜的初始生长过程.经660 ℃退火处理后,Sr/Si衬底表面上形成了纳米岛状结构.经分析,这些纳米小岛为C49-TiSi₂和 C54-TiSi₂.实验结果表明,在没有氧气的情况下退火,Sr/Si界面无法有效阻止SrTiO₃薄膜与Si衬底之间的相互作用. 关键词： 脉冲激光沉积术(PLD) 扫描隧道显微镜(STM) 3')" href="#">SrTiO₃ 2')" href="#">C54-TiSi₂     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.