电压对电刷镀三价铬镀层性能的影响

在45钢表面电刷镀得到三价铬镀层,镀液组成和工艺条件为:Cr2(SO4)36H2O 0.4 mol/L,甲酸铵0.5 mol/L,氨基乙酸0.5 mol/L,H3BO30.6 mol/L,NaH2PO2 H2O 0.3 mol/L,pH=1.5,温度50°C,镀笔移动速率15 cm/s。研究了电压对镀铬层显微结构、表面粗糙度、厚度、显微硬度和耐磨性的影响。随电压增大,镀层厚度增大,显微硬度和耐磨性均先提高后降低。电压为14 V时,镀层的表面平整,粗糙度为2.387μm,显微硬度为602 HV,耐磨性最好。     

脉冲电沉积镍-铜合金

采用脉冲电沉积技术在304不锈钢表面制备Ni-Cu合金镀层,镀液组成和工艺条件为:NiSO4ꞏ6H2O 200g/L,CuSO4ꞏ5H2O 10 g/L,十二烷基硫酸钠0.2 g/L,柠檬酸钠80 g/L,糖精0.2 g/L,pH 4.0,温度25°C,搅拌速率30 r/min,平均电流密度40~120 mA/cm2,脉冲频率0~100 Hz,占空比20%~90%,时间30 min。研究了平均电流密度、脉冲频率和占空比对Ni-Cu合金镀层的元素组成、表面形貌和显微硬度的影响,得到较优的工艺参数为:平均电流密度40 mA/cm2,脉冲频率50 Hz,占空比60%。该条件下所得Ni-Cu合金镀层由质量分数分别为56.53%和43.47%的Ni和Cu组成,呈“菜花”状形貌,结晶细致、均匀,显微硬度为614.4 HV。     

工艺参数对超声辅助脉冲电沉积镍-氮化钛复合镀层的影响

在45钢表面以超声波辅助脉冲电沉积制备Ni-TiN复合镀层。研究了平均阴极电流密度、脉冲占空比、超声功率和TiN粒子(平均直径20~30 nm)添加量对复合镀层的TiN粒子含量和显微硬度的影响。得到较优的工艺参数为:NiSO4ꞏ6H2O 300 g/L,NiCl2ꞏ6H2O 30 g/L,H3BO330 g/L,十二烷基硫酸钠0.3 g/L,TiN 25 g/L,pH 4.1~4.3,温度40°C,平均阴极电流密度4 A/dm2,脉冲占空比40%,脉冲频率1000 Hz,超声功率300 W,机械搅拌速率200 r/min,时间60 min。该条件下所得Ni-TiN复合镀层的TiN质量分数为8.35%,显微硬度为819 HV,表面平整、致密,晶粒尺寸均匀。     

On the linear correlation between microhardness and mechanical properties in polar polymers and blends

The tensile elastic modulus (E), yield stress (σ_Y) and microhardness (MH) of neat and binary and ternary blends of glassy semicrystalline ethylene–vinyl alcohol copolymer (EVOH), a glassy amorphous polyamide and a semicrystalline nylon‐containing ionomer covering a broad range of properties were examined. The tests were carried out on dry and water‐equilibrated samples to produce stiffer and softer materials, respectively. From the results, more accurate linear correlations were found to describe adequately the microhardness, modulus and yield stress of these strongly self‐associated polymers through hydrogen bonding. Copyright © 2003 Society of Chemical Industry     

激光熔敷合金层组织及腐蚀磨损特性研究

利用ＣＯ＿２连续激光器在４５钢表面进行了激光熔敷镍基合金、镍基Ｃｒ＿２Ｏ＿３合金和镍基ＷＣ合金，以２Ｃｒ１３不锈钢为对比材料，系统地研究了激光熔敷层在不同冲击速度和腐蚀介质浓度下的腐蚀磨损特性，并根据组织分析、显微硬度测试及腐蚀磨损后的表面形貌观察，探讨了激光熔敷层的腐蚀磨损过程。结果表明：激光熔敷层的腐蚀磨损性能均比２Ｃｒ１３不锈钢好。     

Evaluation of the reactivity of titanium with mould materials during casting

A methodology for evaluating the reactivity of titanium with mould materials during casting has been developed. Microhardness profiles and analysis of oxygen contamination have provided an index for evaluation of the reactivity of titanium. Microhardness profile delineates two distinct regions, one of which is characterised by a low value of hardness which is invariant with distance. The reaction products are uniformly distributed in the metal in this region. The second is characterised by a sharp decrease in microhardness with distance from the metal-mould interface. It represents a diffusion zone for solutes that dissolve into titanium from the mould. The qualitative profiles for contaminants determined by scanning electron probe microanalyser and secondary ion mass spectroscopy in the as-cast titanium were found to be similar to that of microhardness, implying that microhardness can be considered as an index of the contamination resulting from metal-mould reaction.     

Studies on thermal fatigue in 3Cr2W8V die steel by positron lifetime and hardness measurements

Studies on thermal fatigue in 3Cr2W8V die steel have been carried out by using positron lifetime and microhardness measurements. It is found that the mean positron lifetime and the microhardness exhibit periodic up-and-down variations with an increase in the number of fatigue cycles. The experiments indicate that in the process of thermal fatigue there are two opposing effects on variation of defects: microdeformation and dynamic recovery and recrystallization.     

On the microhardness testing of electrically stressed poly(phenylene oxide): Polystyrene blends

Microhardness measurements have been performed on untreated (virgin) and electrically stressed, solvent‐cast laboratory‐prepared samples of pure poly(phenylene oxide) (PPO), pure polystyrene (PS), and PPO : PS polyblends with different weight proportions. Results of such measurement on untreated polyblend sample show that microhardness (H_v) increases with increase in the content of PS up to 10 wt %, which attributed to the existence of homogeneous phase morphology. However, this feature is not observable in samples containing higher content of PS. Electrical stress is found to modify considerably the mechanical property of polymer. The effect of electric field on the microhardness of such samples (PPO : PS :: 90 : 10) has been characterized by the existence of a peak. Trapping of charge carriers in electrically stressed samples imparts hardening to the polyblend up to an applied step field of 190 kV/cm. However, the excessive charging beyond this step field value destroys this characteristic. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

超声辅助激光修复镍基高温合金V形槽

为了提高失效零件的修复质量,以V形槽为修复对象开展研究,在修复过程中引入超声振动. 耦合声场、温度场与流场建立超声辅助激光修复V形槽的非线性瞬态模型,对修复过程熔池形貌及其温度场进行数值模拟,并开展相关实验研究,分析超声对修复区组织及性能的影响机制. 数值模拟结果表明,超声振动能加速熔池流动与散热,提高熔深,细化晶粒并改善V形槽底部难熔区域的修复效果. 金相、扫描电子显微镜和电子背散射衍射分析结果表明,在超声作用下,晶粒尺寸和一次枝晶间距得到细化,Laves相更加弥散,Nb元素的富集受到抑制;常温和高温硬度在超声作用下分别提高了11.1%、10.4%. 研究表明,超声振动能有效改善镍基高温合金V形槽激光修复区的微观形貌,提高力学性能.     

用GA-BP算法研究超音速电弧喷涂JCW-S-AM涂层显微硬度与工艺参数间的关系

采用超音速电弧喷涂设备在不同工艺参数条件下制备JCW-S-AM涂层,利用显微硬度计测定各种涂层的显微硬度.根据测试结果,运用GA-BP算法构建涂层显微硬度与喷涂电压、喷涂电流的关系模型并进行工艺参数优化.研究结果表明:喷涂电压和喷涂电流对涂层显微硬度均有影响,呈现非线性规律,并且电压和电流之间存在交互作用;通过遗传算法优化,获得的最佳喷涂工艺参数为:喷涂电压29V,电流200A.此时JCW-S-AM涂层显微硬度最大.