Structural health monitoring system based on multi-agent coordination and fusion for large structure

In practical applications of structural health monitoring technology, a large number of distributed sensors are usually adopted to monitor the big dimension structures and different kinds of damage. The monitored structures are usually divided into different sub-structures and monitored by different sensor sets. Under this situation, how to manage the distributed sensor set and fuse different methods to obtain a fast and accurate evaluation result is an important problem to be addressed deeply. In the paper, a multi-agent fusion and coordination system is presented to deal with the damage identification for the strain distribution and joint failure in the large structure. Firstly, the monitoring system is adopted to distributedly monitor two kinds of damages, and it self-judges whether the static load happens in the monitored sub-region, and focuses on the static load on the sub-region boundary to obtain the sensor network information with blackboard model. Then, the improved contract net protocol is used to dynamically distribute the damage evaluation module for monitoring two kinds of damage uninterruptedly. Lastly, a reliable assessment for the whole structure is given by combing various heterogeneous classifiers strengths with voting-based fusion. The proposed multi-agent system is illustrated through a large aerospace aluminum plate structure experiment. The result shows that the method can significantly improve the monitoring performance for the large-scale structure.     

钢管套筒灌浆连接轴向受拉性能模拟试验研究

为研究钢管套筒灌浆连接轴向受拉破坏过程及破坏机理，试验中设计了16组48个钢管套筒灌浆连接试件，试件采用钢板代替圆钢管，并进行静载试验。分析了灌浆料裂缝扩展过程、荷载-相对位移曲线，并对抗剪键高距比、灌浆料厚度、侧向力等因素对破坏过程及承载力的影响进行分析。结果表明：对于不设置抗剪键的套筒灌浆连接试件，斜裂缝随机产生，裂缝分布不均匀；对于设置抗剪键的套筒灌浆连接试件，裂缝首先出现在底部抗剪键位置处，与水平方向夹角约为30°，随后在中部和上部抗剪键位置处分别出现斜裂缝。由于每个抗剪键上荷载分担并不均匀，与抗剪键接触的灌浆料逐渐达到极限压应力，达到极限状态时，承载力全部由抗剪键间的机械咬合力承担，在连接承载力中，可忽略摩擦力和胶结力作用。随着抗剪键高距比h/s增大，各试件初始剪切刚度相差不大，承载力增大，但增幅逐渐减小，建议抗剪键高距比0.06g/s>0.3，同时需要满足灌浆料灌注的施工要求。     

Design trade-offs in self-management technology: the HeartMan case

ABSTRACT

Health self-management technology has the potential to significantly improve the Quality of Life of patients suffering from chronic diseases. However, designing the technology involves numerous highly context-dependent design decisions. In this paper, we analyse a case study of self-monitoring technology in the field of congestive heart failure. We analyse the design process of the technology from the perspective of design trade-offs. Three important trade-offs related to health self-monitoring technology are described in detail, related to patient autonomy, technology appropriation, and patient well-being. For each of the trade-offs, various mediating factors that influence design decisions are described in detail. On a practical level, this analysis can inform future developments in self-management technology. In addition, this design trade-off analysis provides intermediary knowledge that can contribute to a better theoretical understanding of health self-management technology.     

漆包机烘炉加热失效原因探究及处理

针对漆包机烘炉加热失效形式及产生原因,进行了深入的研究和分析。结果表明,影响烘炉加热失效的主要原因是加热管损坏及装配异常、催化剂表面粘有金属化合物等颗粒杂质、排废风机转速设定不合理,并对加热管、催化剂、排废风机提出了合理实用的技术措施,为降低烘炉加热失效提高加热效果提供帮助。     

Interfacial failure analysis of functionally graded adhesively bonded double supported tee joint of laminated FRP composite plates

This paper deals with three-dimensional non-linear finite element analyses to assess the structural behavior of adhesively-bonded double supported tee joint of laminated FRP composites having embedded interfacial failures. The onset of interfacial failures is predicted by using Tsai–Wu coupled stress failure criterion with pre-determined stress values. The concept of fracture mechanics principle is utilized to study the sustainability of the tee joint having interfacial failures pre-existed at the critical locations. Individual modes of the strain energy release rates (SERR) G_I, G_II and G_III, are considered as the damage growth parameters and, are evaluated using the Modified crack closure integral (MCCI) technique based on the concept of linear elastic fracture mechanics (LEFM). Based on the stress analyses, it has been observed that the interfacial failures in tee joint structure trigger at the interface of base plate and adhesive layer from both ends of base plate. Depending on the SERR magnitudes, it has been noticed that the interfacial failure propagates under mixed mode condition. Therefore total SERR (G_T) is considered as the governing parameter for damage propagation. Furthermore, efforts have been made to retard damage propagation rate by employing functionally graded adhesive (FGA) instead of monolithic adhesive material. Series of numerical simulations have been performed for varied interfacial failure length in functionally graded adhesively bonded double supported tee joint structure in order to achieve the significant effect of FGA with various modulus ratios on SERR. Material gradation of adhesive indicates significant SERR reduction at the incipient stage of failure which necessitates the use of functionally graded adhesive for the tee joint and prolong the service life of the structure.     

Adaptive actuator failure compensation design for unknown chaotic multi‐input systems

In this paper, an adaptive control approach is designed for compensating the faults in the actuators of chaotic systems and maintaining the acceptable system stability. We propose a state‐feedback model reference adaptive control scheme for unknown chaotic multi‐input systems. Only the dimensions of the chaotic systems are required to be known. Based on Lyapunov stability theory, new adaptive control laws are synthesized to accommodate actuator failures and system nonlinearities. An illustrative example is studied. The simulation results show the effectiveness of the design method. Copyright © 2014 John Wiley & Sons, Ltd.     

Strain‐rate‐dependent mechanical properties of polypropylene separator for lithium‐ion batteries

The mechanical integrity of battery separators is critical for battery safety and durability. A comprehensive study of strain‐rate‐dependent tensile and puncture properties of a polypropylene lithium‐ion battery separator is presented here with a new model. Due to anisotropy of the polymeric membrane, tensile testing was conducted for different directions. Results showed that tensile strength and elastic modulus were increased 1000% and 500%, respectively, for different directions. It was also demonstrated that tensile strength changed 10 to 25% with strain rate (1.67 × 10^?4 to 1.67 × 10^?1 s^?1) for different directions. An equation was obtained for the first time for flow stress versus strain rate at varied tensile directions with respect to machine direction. Moreover, puncture testing was performed and it was shown that puncture strength was increased 140% with increasing strain rate from 0.25 to 250 mm min^?1. Two failure modes were also observed in puncture samples. Finally, Eyring's model was used to calculate activation enthalpy of the porous polypropylene separator. © 2020 Society of Chemical Industry     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Colostrum source and passive immunity transfer in dairy bull calves

Colostrum is essential for good neonate health; however, it is not known whether different calves absorb the nutrients from colostrum equally well. In this study, the absorption of protein, IgG, and γ-glutamyl transferase was compared in newborn dairy bull calves for 1 wk after feeding colostrum from different sources. Thirty-five Holstein-Friesian bull calves were randomly allocated into 3 groups and fed colostrum within 4 h after birth. Group A calves (n = 12) were bottle fed colostrum from their own dam for 3 d. Colostrum from these group A cows was also used as foster cow colostrum for the group B calves (n = 12), such that each group A and B calf pair received identical colostrum from each milking of the respective group A dam (10% of birth weight per day). The group C calves (n = 11) were fed 1 bottle (2 L) of pooled colostrum and transition milk (referred to as pooled colostrum), as was the standard practice on the dairy farm. The pooled colostrum was collected from the other dairy cows on the farm 0 to 4 d postpartum and stored at 4°C for less than 12 h. Blood was sampled from calves before the first feeding and at 1, 2, 3, and 7 d after birth. Levels of total solids, total protein, and IgG were higher in the dam colostrum than in the pooled colostrum. At birth, there were no differences between the calf groups for any measurements, and all calves had very low IgG levels. After receiving colostrum, the glucose, plasma γ-glutamyl transferase, serum total protein, and IgG concentrations increased significantly in all calves. There were no differences in any blood measurements at any time point between the pairs of group A and group B calves that received colostrum from the same cow except for the IgG concentration 2 d after birth. However, the group A calves had a higher total serum protein level and IgG concentration than the group C calves for all the time points after the first feeding. The group B calves had a higher IgG concentration than the group C calves on d 1, 2, and 7 after birth. Compared with groups A and B, there was no difference in the proportion of calves in group C that failed to have passive immunity transferred adequately based on the IgG threshold (<10 g/L). Thus, the calves receiving identical colostrum from the same cow had the same levels of IgG, and even the pooled colostrum provided sufficient transfer of IgG as the calves were fed within 4 h after birth.