无线传感器网络中移动sink节点的路径规划

在无线传感器网络中,大量感知数据汇集到sink节点的采集方法会导致sink节点附近的节点能量耗尽,造成能量空洞。针对该问题,利用移动的sink节点进行数据收集是一种解决方法,其中移动sink的路径规划成为一个重要的问题。提出了一个移动sink路径规划算法,将无线传感器中随机分布的节点划分为不同的子区域,寻找sink节点移动的最佳转向点,最终得到最优的移动路径,以实现无线传感器网络生命周期最大化。仿真实验表明,与现有方案相比,该算法能显著延长网络的生命周期。     

刀尖圆弧半径补偿对球面零件车削加工影响的分析

采用刀尖圆弧半径为0.4 mm的刀片,以0、0.4 mm、0.8 mm、1.2 mm为刀尖圆弧半径补偿值,得到球面曲率半径不同的四个试件,基于三丰C-3200测量仪对球面轮廓度进行测量,分析刀尖圆弧半径补偿对球面零件车削加工的影响。分析结果表明,在进行凸球面零件加工时,HNC-818A数控系统中的刀尖圆弧半径补偿功能有效,球面的曲率半径与刀尖圆弧半径补偿值的单调性一致。当刀尖圆弧半径补偿值线性变化时,球面的曲率半径呈非线性变化。当设定刀尖圆弧半径为真实值时,球面轮廓最为理想。在球面零件加工实践中,使用刀尖圆弧半径补偿功能,精加工采用可转位机夹车刀,通过试切法合理修改刀尖圆弧半径补偿值,可以提高球面零件的车削加工质量。     

An element-free Galerkin method approach for estimating sensitivity of machined surface parameters

The main objective of this study is to implement a parameter sensitivity analysis method to be used in the search of optimal machining conditions with respect to surface quality. Presently, the element-free Galerkin (EFGM) approximating functions are used to evaluate the properties of machined surfaces with cutting parameters when turning AISI 4140 steel using arbitrary sets of experimental values and the EFGM approximation functions, based on the moving least-squares method, in order to obtain the sensitivities through proper local derivations. This method shows the sensitivity of each surface parameter for each input variable. The variables investigated were cutting speed (v_c), depth of cut (a_p), feed rate (f) and the surface roughness (R_a). The sensitivity results showed that the feed rate has the highest influence on surface roughness when turning AISI 4140 steel followed by cutting speed and depth of cut.     

ABS塑料工件的车削加工

详细介绍了ABS塑料工件车削加工的特点，根据ABS车削加工过程中切削力小、切削温度低，热导率小、线膨胀系数大、弹性模量小的特点，需正确选择车刀的几何参数。     

高速硬车削淬火钢的实验研究

通过改变高速车削淬火钢（Cr12）的切削用量，对切削力、切削温度、加工表面质量等进行了研究，结果表明合理选择切削用量，高速硬车削淬火钢可显著提高生产率及加工表面质量，并在一定程度上可取代磨削加工。     

Scientific Screening of Raw Diamond for an Ultraprecision Cutting Tool with High Durability

The wide scattering in tool life of natural mono-crystalline diamond tools is considered to depend on intrinsic crystalline defects due to nitrogen impurities in raw diamond. In this paper, the correlation was investigated between the amounts and types of the impurity evaluated by infrared absorption (IRA) and the crater wear and chipping resistances. As a result, diamonds including less total amount of impurity show larger wear resistance and that with larger amount of B2-aggregates show larger chipping resistance. This suggests that the inspection by IRA can be a useful method for screening of raw diamond for highly durable cutting tools.     

Distortion Engineering - Identification of Causes for Dimensional and Form Deviations of Bearing Rings

Distortion of power transmission parts after heat treatment is influenced by each step of the process chain, ranging from material production to hard-machining. However, an experimental analysis for each production step in the manufacture of bearing rings has shown that distortion is significantly influenced by turning before heat treatment. Elastic ring deformation caused by fixing the workpiece in the chuck leads to a variation of the depth of cut and polygonal form deviations occur after machining. In addition the cutting process induces locally varying residual stresses which also contribute to dimensional and form deviations of machined rings. In this paper results from experimental investigations of the principle physical causes for the distortion of bearing rings are presented and discussed. Finally, strategies for the minimization of distortion are derived.     

基于CAN总线DZY300型运梁车转向系统设计与工程实现

本文介绍了上海磁悬浮工程专用DZY300型运梁车的转向系统设计原理与实现过程。以CAN总线为基础，来实现转角信号的实时检测和电液比例阀的远端控制；从而利用总线通讯技术，实现了大闭环控制系统。在采用经典PID控制律时，针对工程实际情况进行了改进。理论充分与实际相结合，保证调节实时性的同时，有效地解决了转向系统中出现的超调振荡、反复微调节和调节不平稳现象。     

热膨胀法判定建窑黑瓷烧成温度的应用研究

以热膨胀仪判定建窑黑瓷烧成温度的研究为例,综合运用多种测试方法对建窑黑瓷标本进行了系统研究,探讨如何从建窑黑瓷胎体重烧热膨胀曲线中筛选有效转折点的问题及其转折点的形成原因。研究表明:(1)建窑黑瓷胎体重烧热膨胀曲线上有三个转折点,分别为收缩转折点、膨胀转折点和急剧收缩点。其中第一个收缩转折点是判定其古代烧成温度的关键点。(2)建窑黑瓷胎体重烧热膨胀曲线上膨胀转折点和急剧收缩点的形成皆与其胎体中大量Fe_2O_3在高温下发生分解反应有关。该研究不仅为热膨胀仪测定建窑黑瓷烧成温度的应用研究提供判定依据,也将为科学认识古陶瓷胎体重烧热膨胀曲线上多个转折点的形成机理提供数据支持。     

浅析曲面回转体零件的数控车削加工

从曲面回转体零件数控车削中刀具选用、加工路线拟定、数控程序编制3个方面,详细分析了尖形车刀加工曲面的干涉现象、圆弧形车刀半径选择原则、常见加工路线的特点比较、加工程序编制中的基点和节点坐标计算要点、利用子程序简化加工程序编写方法等问题,并提出相应的解决方法或思路.