用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

超宽带大功率合成器设计北大核心CSCD

在80 MHz~1 GHz频段,单个功率管输出功率能达到100 W以上,为研制输出功率400 W的功率放大器,文中设计了四路功率合成器。该合成器需要实现功率容量大、工作频带宽、体积小的设计目标。在功率容量方面,文中采用悬置带状线结构,其功率容量远远大于微带线结构;在工作频带方面,采用切比雪夫九节阻抗变换器,将工作带宽拓宽为80 MHz~1 GHz;在体积方面,文中合成器的功率合成部分采用Y型节级联实现四路功率合成,阻抗变换部分采用切比雪夫阻抗变换器进行阻抗变换,该结构相较于磁环巴伦功率合成器,不但具有损耗小、平坦度高的优点,而且通过将阻抗变换器设计成曲折的形状,进一步缩小了合成器体积。仿真与实测结果显示该合成器在80 MHz~1 GHz范围内还具有较高的平坦度,合成效率可达90%以上。     

An active balancer with rapid bidirectional charge shuttling and adaptive equalization current control for lithium-ion battery strings

This article proposes an active balancer, which features bidirectional charge shuttling and adaptive equalization current control, to fast counterbalance the state of charge (SOC) of cells in a lithium-ion battery (LIB) string. The power circuit consists of certain bidirectional buck-boost converters to transfer energy among the different cells back and forth. Owing to the characterization of the open-circuit voltage (OCV) vs SOC in LIB being relatively smooth near the SOC middle range, the SOC-inspected balance strategy can achieve more precise and efficient equilibrium than the voltage-based control. Accordingly, a compensated OCV-based SOC estimation is put forward to take into account the discrepancy of SOC estimation. Besides, the varied-duty-cycle (VDC) and curve-fitting modulation (CFM) methods are devised herein to tackle the problems of slow equalization rate and low balance efficacy, which arise from the diminution in balancing current as the SOC difference between the cells decreases in the later duration of equalization especially. The proposed strategies have taken the battery nonlinear characteristic and circuit parameter nonideality into account and can adaptively modulate the duty cycle with the SOC difference to keep balancing current constant throughout the balancing cycle. Simulated and experimental results are given to demonstrate the feasibility and effectiveness of the same prototype constructed. Compared with the fixed duty cycle and the VDC methods, the proposed CFM has the best balancing efficiency of 81.4%, and the balance time is shortened by 27.1% and 18.6%, respectively.     

A novel quasi-oppositional harmony search algorithm and fuzzy logic controller for frequency stabilization of an isolated hybrid power system

The intermittent wind power in isolated hybrid distributed generation (IHDG) may cause serious problems associated with frequency (f) and power (P) fluctuation. Energy storage devices such as battery, super capacitor, and superconducting magnetic energy storage (SMES) may be used to reduce these fluctuations associated with f and P. This paper presents a study of IHDG power system for improving both f and P deviation profiles with the help of SMES. The studied IHDG power system is consisted of wind turbine generator and diesel engine generator. Both f and P control problems of the studied power system model are addressed in presence or absence of SMES. Fuzzy logic based proportional–integral–derivative (PID) controller with SMES is used for the purpose of minimization of f and P deviations. The different tunable parameters of the PID controller and those of the SMES are tuned by a novel quasi-oppositional harmony search algorithm. Performance study of the IHDG power system model is carried out under different perturbation conditions. The results demonstrate minimum f and P deviations may be achieved by using the proposed fuzzy logic based PID controller along with SMES.     

基于RFID标签阵列的睡眠期间呼吸量连续监测系统

睡眠期间连续且准确的呼吸量监测有助于推断用户的睡眠阶段以及提供一些慢性疾病的线索。现有工作主要针对呼吸频率进行感知和监测,缺乏对呼吸量进行连续监测的手段。针对上述问题提出了一种基于商用无线射频识别(RFID)标签的无线感知用户睡眠期间呼吸量的系统——RF-SLEEP。RF-SLEEP通过阅读器连续收集附着在胸部表面的标签阵列返回的相位值及时间戳数据,计算出呼吸引起的胸部不同点的位移量,基于广义回归神经网络(GRNN)构建胸部不同点的位移量与呼吸量之间的关系模型,从而实现对用户睡眠期间呼吸量的评估。RF-SLEEP通过在用户肩膀处附着双参考标签,消除用户睡眠期间翻转身体对胸部位移计算造成的误差。实验结果表明,RFSLEEP对不同用户睡眠期间的呼吸量连续监测的平均精确度为92.49%。     

A new design strategy for DC/DC LLC resonant converter: Concept,modeling, and fabrication

In this paper, a new design procedure for LLC converter has been introduced. In fact, this method is a computer-based design algorithm based on a numerical technique. In the process of designing, the value of the resonant element is obtained by solving the LLC converter fundamental equation. This converter will be controlled by using state feedback, such as output voltage variable. As a matter of fact, in a control system, the change of output voltage (because of load variation) will affect the switching frequency, so the output voltage will be tuned. In the designing process, the fundamental equations of LLC converter are obtained, and the value of the resonant elements is calculated. Also, a comparison analysis is carried out between the proposed and typical methods. The simulation is done to investigate the validity of the proposed method. Moreover, a prototype is manufactured, and the experimental test is done to evaluate its applicability.     

2020年电子电路技术热点

文章归纳了2020年电子电路产业一些技术热点,主要有5G电路板设计和基材,制造方面半加成法、3D打印、直接金属化孔电镀和垂直互连结构等技术,以及集成电路封装载板技术。     

ACCUGRAM: A novel approach based on classification to frequency band selection for rotating machinery fault diagnosis

Frequency band selection (FBS) in rotating machinery fault diagnosis aims to recognize frequency band location including a fault transient out of a full band spectrum, and thus fault diagnosis can suppress noise influence from other frequency components. Impulsiveness and cyclostationarity have been recently recognized as two distinctive signatures of a transient. Thus, many studies have focused on developing quantification metrics of the two signatures and using them as indicators to guide FBS. However, most previous studies almost ignore another aspect of FBS, i.e. health reference, which significantly affect FBS performance. To address this issue, this paper investigates importance of a health reference and recognize it as the third critical aspect in FBS. With help of the health reference, the frequency band where the fault transient exists could be located. A novel approach based on classification is proposed to integrate all three aspects (impulsiveness, cyclostationarity, and health reference) for FBS. Classification accuracy is developed as a novel indicator to select the most sensitive frequency band for rotating machinery fault diagnosis. The proposed method (coined by accugram) has been validated on benchmark and experiment datasets. Comparison results show its effectiveness and robustness over conventional envelope analysis, the kurtogram, and the infogram.     

Rogowski coil current transducer compensation method for harmonic active power error

In the harmonic active power measurement, the highest uncertainties are generally introduced by the current and voltage transducers. In a previous paper, the authors showed that the current transformer (CT) can introduce significant errors in such measurement, especially if the phase shift between voltage and current is close to ±90°. In such condition the errors on harmonic power measurement are mainly due to the CT phase displacement. This paper shows that better results can be achieved with more linear transducers, such as the Rogowski coil current transducers (RCCTs), whose metrological performance in distorted condition can be improved, by means of a proper compensation method. The proposed method for RCCTs compensation is based on the frequency response and it allows to reduce the errors on harmonic power measurement, also for phase shift close to ±90°. The study is supported by several experimental tests.     

A probabilistic load shedding concept considering highly volatile local generation

Automatic load shedding is the ultimate countermeasure against imbalance in a power system and can effectively help preventing large blackouts. Taking into account a high penetration of renewable energy sources (RES) in the distribution grid, a clear distinction between load and generation at the PCC becomes increasingly more difficult. For that reason an adaptation of frequency relay parameters and their locations of installation are necessary. In Europe this is rest on a multi-step plan based on values such as the yearly peak load. In this paper a novel probabilistic method for automatic load shedding is presented that uses the average values instead of peak values for load shedding. Its applicability is verified by a dynamic power system model that was developed to compare the classical and novel probabilistic load shedding principle. The method is verified using data from a German TSO.