Synthesis and performance evaluation of a new drag reducer based on acrylamide/12-allyloxydodecyl acid sodium

Hydraulic fracturing with slickwater is a field-proven stimulation technology used in tight reservoirs. Because of the high pumping rate associated with slickwater fracturing, drag reduction (DR) is critical in minimizing pressure drop and the success of oilfield operations. In this paper, a new type of drag reducer (SPR) was synthesized with acrylamide and 12-allyloxydodecyl acid sodium, and its drag reduction performance was evaluated. The results showed that the new drag reducer features low molecular weight, fast-dissolving rate and low interfacial tension. The algorithm of estimating the drag reduction rate of non-Newtonian fluid SPR was proposed and validated. Empirical or semianalytical models for estimating the friction ratio (σ) or friction factor (λ or f) were used to simulate the turbulence behavior of the SPR drag reducer under different Reynolds numbers (Re). The modified Virk's correlation could accurately model the turbulent behavior of the SPR drag reducer. A unified calculation formula was established in this study for different pipe diameters.     

新型刮刀钻头的设计及现场试验研究

在理论分析的基础上，综合PDC钻头和刮刀钻头的优点，设计了一种新型的刮刀钻头，并进行了现场试验。现场试验结果表明，该钻头运转平稳，采用低钻压、高转速，钻进速度快，井眼规则通畅，有较明显的防斜作用，该种钻头的推广应用对提高钻井工程的整体效益具有十分重要的意义。     

On the boundary-layer control through momentum injection: Studies with applications

The concept of moving surface boundary-layer control, as applied to a Joukowsky airfoil, is investigated through a planned experimental programme complemented by numerical studies. The moving surface was provided by rotating cylinders located at the leading edge and/or trailing edge as well as top surface of the airfoil. Results suggest that the concept is quite promising, leading to a substantial increase in lift and a delay in stall. Depending on the performance desired, appropriate combinations of cylinder geometry, location and speed can be selected to obtain favourable results over a wide range of angle of attack. Next, effectiveness of the concept in reducing drag of bluff bodies such as a two-dimensional flat plate at large angles of attack, rectangular prisms and three-dimensional models of trucks is assessed through an extensive wind tunnel test-programme. Results show that injection of momentum through moving surfaces, achieved here by introduction of bearing-mounted, motordriven, hollow cylinders, can significantly delay separation of the boundary-layer and reduce the pressure drag. The momentum injection procedure also proved effective in arresting wind-induced vortex resonance and galloping type of instabilities. A flow visualization study, conducted in a closed-circuit water tunnel using slit lighting and polyvinyl choride tracer particles, adds to the wind-tunnel and numerical investigations. It shows, rather dramatically, the effectiveness of the moving surface boundary-layer control (MSBC). The Sabita Chaudhury Memorial Lecture The models were fabricated in the Mechanical Engineering Workshop. The assistance of M/s E Abell, P Hurren and D Camp in the design and construction of the models is gratefully acknowledged. The investigation was supported by the Natural Sciences and Engineering Research Council of Canada, Grant No. A-2181.     

轧机锁紧油缸泄漏原因分析及系统改进

济钢第一小型轧钢厂轧机液压换槽系统因工作压力增高，蓄能器压力油长期作用于锁紧缸，引起密封圈击穿、泄漏和机架不稳。通过增设定值减压阀控制油压，改进锁紧油缸结构，解决了锁紧油缸的泄漏问题，保证了轧制线的稳定，轧机作业率由85％提高到87％。     

多排数翅片管空冷器风阻特性的数值模拟

本文对多排数翅片管空冷器空气侧的风阻特性进行了数值模拟.利用商用软件Fluent进行数值计算,结合经验公式和已有的实验数据,分析了不同入口风速下,阻力的变化规律以及流动阻力和温度变化对模拟计算的影响.     

油溶性减阻功能聚合物的研制

介绍了以混合α-烯烃为原料,制备了具有减阻功能的共聚物。讨论了催化剂浓度、聚合温度、预聚合时间、原料单体中杂质含量对共聚物特性粘度和转化率的影响。试验表明,在较低的催化剂浓度和预聚合温度下,能得到较高分子量的聚合物。气相色谱法和DSC法测定其组成和单体混合物的组成基本一致,表明共聚物是一种无规的梳状结构聚合物。该聚合物达到较高特性粘度时,能获得较好的减阻率。     

防止减速器“跑,冒,漏”油的几种新方法

介绍了防止减速器“跑，冒，漏”油的几种新方法。     

井下减速器传动方案分析

结合井下减速器的结构特点，分析了定轴轮系传动、2K-H型行星轮系传动、3K行星轮系传动、少齿差行星轮系传动4种传动方案，选择内齿作为输出轴的少齿差行星轮系传动方案更符合涡轮钻具的传动要求和井下工具结构特点。少齿差行星轮系的研制、开发、应用可降低涡轮钻具转速，提高扭矩，提高深井钻速。     

浅谈电动潜油单螺杆采油系统的研究开发

介绍了国内外各种螺杆泵采油系统的发展现状，并对电动潜油螺杆泵采油系统中齿轮减速器这一关键部件的方案选择进行了分析，旨在为研制开发国产高性能电动潜油螺杆采油系统提供参考。     

柔性管自激振动减阻效果的实验研究

在实验确认柔性管紊流减阻效果的基础上,采用双重管结构,对柔性管的自激振动减阻效果进行了实验研究。结果表明:管的壁厚越小自激振动的减阻率越大;在雷诺数约为2.2×104时,壁厚为2 mm,3 mm及4 mm的柔性管自激振动减阻率依次约为13%,10%,8%。