用于电弧检测的电力专用SoC设计

针对传统的电弧电路故障检测结果不准确的问题,设计用于电弧检测的SoC系统,并且在55nm工艺下进行流片验证。采用包含两种结构的模数转换器的片上电压源,设计了锁相环以及复位电路,精度最高可达8.67 bit。验证结果表明,本设计可提高电弧检测的准确性。     

A practical Equivalent Electrical Circuit model for Proton Exchange Membrane Fuel Cell (PEMFC) systems

An alternative Equivalent Electrical Circuit for Proton Exchange Membrane Fuel Cells is modelled in this study. Both I–V characteristics and H₂ consumptions corresponding to generated power under load and no-load conditions are investigated. For this purpose, H₂ consumptions and I–V characteristics of three different sized PEMFCs are tested. There is a very good harmony between the model results and measured values (relative error %0.7, %6.4 and %2.5 for FC-A, FC-B and FC-C respectively). In the proposed model current passes only on parallel resistance and not on serial resistance at no-load condition. Thus, a FC with higher parallel resistance should be preferred. Another key output of this study is that based on the proposed model, performance comparison of FCs can be performed with the parameters defined in this work. Proposals made in this study can easily be used for performance analysis of FCs under for both steady state and transient analysis.     

2020年电子电路技术热点

文章归纳了2020年电子电路产业一些技术热点,主要有5G电路板设计和基材,制造方面半加成法、3D打印、直接金属化孔电镀和垂直互连结构等技术,以及集成电路封装载板技术。     

High‐intensity sweeteners in espresso coffee: ideal and equivalent sweetness and time–intensity analysis

The efficient substitution of sucrose by a sweetener in beverages requires the application of some sensory techniques. First, one must determine the concentrations of the sweeteners under study, equivalent in sweetness to the ideal sucrose concentration. In addition, it is fundamental to determine which is most similar to sucrose. The objectives of this study were to determine the ideal sweetness for espresso coffee and the equivalent concentrations in sweetness of different sweeteners, as well as characterise the time–intensity profile of each sweetener in relation to sweetness. The sweeteners evaluated were sucralose, aspartame, neotame, a cyclamate/saccharin mixture (2:1) and stevia. The sucrose concentration considered ideal by consumers was 12.5% (w/v), and the equivalent concentrations of the sweeteners were 0.0159% for sucralose, 0.0549% for aspartame, 0.0016% for neotame, 0.0359% for the cyclamate/saccharin mixture and 0.0998% for stevia. The time–intensity analysis indicated that possibly the sweeteners neotame, aspartame and sucralose would be the best substitutes for sucrose.     

“Size effect” in the fatigue behavior of Friction Stir Welded plates

Comparative fatigue tests were carried out on Friction Stir Welded specimens of a 2195-T8 aluminum–lithium alloy that differed significantly in width. The width of the larger specimens was over thirteen times greater than that of the small specimens. Fatigue results showed a clear “size effect”, i.e. fatigue life of large specimens was about 40% of the corresponding value of small specimens. The Equivalent Initial Flaw Size methodology was adopted to correlate the two sets of results. Fatigue crack initiation life was disregarded with respect to crack propagation life, and fatigue life was evaluated only as propagation of a small pre-existing defect. Following this methodology, test results of small specimens were used to evaluate the initial equivalent flaw contained in each specimen. It was assumed that this data followed a normal distribution. The equivalent initial flaw in larger specimens was evaluated by simple geometrical considerations. A very good assessment of mean fatigue life and scatter in the fatigue results of large specimens was obtained by simulating the propagation of these defects. Calculations were carried out by taking also welding residual stresses into account, but the results demonstrated that this effect was not significant.     

微机织机监测的巡检系统

本文介绍织机监测的数据采集系统即巡检系统,重点讨论了巡检方案的选择、巡检电路的设计、巡检软件的编制以及几种抗干扰的措施。     

对水轮机自动调速器油压控制电路的改进

YT－1000型油压自动调速器在运行中不能维持正常油压、在不增加任何设备的情况下，只改动二次接线的处理方法，就能消除隐患、解决问题。     

A novel compact circuit for 4-PAM energy-efficient high speed interconnect data transmission and reception

Transmission of signals, whether on-chip or off-chip, places severe constraints on timing and extracts a large price in energy. New silicon device technologies, such as back-plane CMOS, provide a programmable and adaptable threshold voltage as an additional tool that can be used for low power design. We show that one particularly desirable use of this freedom is energy-efficient high-speed transmission across long interconnects using multi-valued encoding. Our multi-valued CMOS circuits take advantage of the threshold voltage control of the transistors, by using the signal-voltage-to-threshold-voltage span, in order to make area-efficient implementations of 4-PAM (pulse amplitude modulation) transceivers operating at high speed. In a comparison of a variety of published technologies, for signal transmission with interconnects of 10-15 mm length, we show up to 50% improvement in energy for on-chip signal transmission over binary encoding together with higher limits for operating speeds without a penalty in circuit noise margin.     

Matlab语言与线性电路的符号仿真

目前的电路仿真软件通常是在电路中所有元件值都是给定的情况下得到一些数值结果，而非解析结果。该文利用Matlab的符号运算功能编程，通过节点列表法，实现了任意线性电路的自动解析求解，为电路分析提供了一个有效的辅助工具。     

Education-driven research in CAD

We argue for a new research category, named education-driven research (EDR), which fills the gap between traditional field-specific research that is not concerned with educational objectives and research in education that focuses on fundamental teaching and learning principles and possibly on their customization to broad areas (such as mathematics or physics), but not to specific disciplines (such as CAD). The objective of EDR is to simplify the formulation of the underlying theoretical foundations and of specific tools and solutions in a specialized domain, so as to make them easy to understand and internalize. As such, EDR is a difficult and genuine research activity, which requires a deep understanding of the specific field and can rarely be carried out by generalists with primary expertise in broad education principles. We illustrate the concept of EDR with three examples in CAD: (1) the Split and Tweak subdivisions of a polygon and its use for generating curves, surfaces, and animations; (2) the construction of a topological partition of a plane induced by an arbitrary arrangement of edges; and (3) a romantic definition of the minimal and Hausdorff distances. These examples demonstrate the value of using analogies, of introducing evocative terminology, and of synthesizing the simplest fundamental building blocks. The intuitive understanding provided by EDR enables the students (and even the instructor) to better appreciate the limitations of a particular solution and to explore alternatives. In particular, in these examples, EDR has allowed the author to: (1) reduce the cost of evaluating a cubic B-spline curve; (2) develop a new subdivision curve that is better approximated by its control polygon than either a cubic B-spline or an interpolating 4-point subdivision curve; (3) discover how a circuit inclusion tree may be used for identifying the faces in an arrangement; and (4) rectify a common misconception about the computation of the Hausdorff error between triangle meshes. We invite the scientific community to encourage the development of EDR by publishing its results as genuine research contributions in peer-reviewed professional journals.