Effect of Praseodymium on Superconductivity and Magnetism in Y1–xPrxBa2Cu4O8 Prepared by Nitrite Pyrolysis Method

X-ray diffraction patterns show that most samples of Y_1-x Pr_xBa₂Cu₄O₈ examined in the present study contained a single YBa₂ Cu₄O₈ (1-2-4) superconductive phase for x<0.7.Lattice parameters a and b increased with Pr concentration, suggesting that most of the Pr is trivalent in Y_1-x Pr_x-Ba₂Cu₄O₈. The zero-resistance temperature, T _co, decreases monotonically from 80 K at x=0 to 12 K at x=0.65, and superconducting transition widths tend to broaden for x>0. The room-temperature resistivity changes linearly until x=0.7 and increases abruptly at x=-0.75. The critical concentration, x_cr, thus was estimated to be 0.7. The effective magnetic moments of Pr in Y _1-x Pr_xBa₂Cu₄O₈ were 3.63., 3.35, and 3.23, μ_B for x=0.2, 0.4 and 0.6, respectively. In the R_0.8 Pr_0.2Ba₂Cu₄O₈ system, the depression of T_c weakly depends on the ionic radius of rare-earth elements. Similarities and differences between Y _1-x Pr_xBa₂Cu₄O₈ and Y_1-xPr_x-Ba₂Cu₃O_7-y also were noted and are discussed in this paper.     

Synthesis and bulk acoustic wave properties on the dual mode frequency shift of solidly mounted resonators

This study focused on the fabrication and the theoretical analysis of solidly mounted resonators (SMR) concerning dual-mode frequency responses and their frequency shift of bulk acoustic wave (BAW) resonance. For this device fabrication, RF/DC magnetron sputtering and photolithography were employed to constitute the required multilayer structure. For the theoretical analysis, the dualmode frequency shift was characterized by the Sauerbrey's formula, and a modified formula was carried out following the trend for the large frequency shift. In the fabrication of the SMR device, Mo/SiO2 was chosen to construct the Bragg reflector as the high/low acoustic impedance materials, respectively, and aluminum nitride (AlN) was used as a piezoelectric layer. To investigate the characteristics of BAW on the dual-mode frequency shift, the c-axis tilted angle of AlN was altered as well as the various mass loading on the SMR. Based on the experimental results, the dual-resonance frequencies showed a nonlinear decreasing trend with a linear increase of the mass loading. Therefore, a modified formula was carried out. Furthermore, the ratio of the longitudinal-resonant frequency to the shear-resonant frequency remained at a range around 1.76 despite the various c-axis tilted angles of AlN and gradual mass loading on the SMR. The electromechanical coupling coefficient, k2(eff), of the shear resonance rose with the increase of the c-axis tilted angle of AlN.     

Highly sensitive mass sensor using film bulk acoustic resonator

Film bulk acoustic resonators (FBAR) have recently been adopted as alternatives to surface acoustic wave (SAW) in high frequency devices, due to their inherent advantages, such as low insertion loss, high power handling capability and small size. FBAR device can also be one of the standard components as mass sensor applications. FBAR sensors have high sensitivity, good linearity, low hysteresis and wide adaptability. In this study, a highly sensitive mass sensor using film bulk acoustic resonator was developed. The device structure of FBAR is simulated and designed by the Mason model, and fabricated using micro electromechanical systems (MEMS) processes. The fabricated FBAR sensor exhibits a resonant frequency of 2442.188 MHz, measured using an HP8720 network analyzer and a CASCADE probe station. Experimental results indicate that the mass loading effects agree with the simulated ones. Results of this study demonstrate that the sensitivity of the device can be achieved as high as 3654 Hz cm²/ng.     

State-of-Charge Estimation for Electric Scooters by Using Learning Mechanisms

Because of its nonlinear discharge characteristics, the residual electric energy of a battery remains an open problem. As a result, the reliability of electric scooters or electric vehicles is lacking. To alleviate this problem and enhance the capabilities of present electric scooters or vehicles, we propose a state-of-charge learning system that can provide more accurate information about the state-of-charge or residual capacity when a battery discharges under dynamic conditions. The proposed system is implemented by learning controllers, fuzzy neural networks, and cerebellar-model-articulation-controller networks, which can estimate and predict nonlinear characteristics of the energy consumption of a battery. With this learning system, not only could it give an estimate of how much residual battery power is available, but it also could provide users with more useful information such as an estimated traveling distance at a given speed and the maximum allowable speed to guarantee safe arrival at the destination     

Thickness-dependent leakage current of (polyvinylidene fluoride/lead titanate) pyroelectric detectors

The novel pyroelectric IR detectors have been fabricated using the Polyvinylidene Fluoride (PVDF)/Lead Titanate (PT) pyroelectric bilayer thin films, which were deposited onto Pt(111)/SiO/sub 2//Si(100) substrates by a sol-gel process. The ceramic/polymer structure was constructed of the randomly oriented polycrystalline PT film (/spl sim/1 /spl mu/m) heated at 700/spl deg/C for 1 h and the /spl beta/-phase PVDF film crystallized at 65/spl deg/C for 2 h. The effects of PVDF thin film thickness (100 /spl sim/ 580 nm) on the pyroelectric response of IR detectors were studied. The results show that the depositions of PVDF thin films onto the PT films will cause the leakage current (J) of the detectors decrease from 6.37/spl times/10/sup -7/ A/cm/sup 2/ to 3.86/spl times/10/sup -7/ A/cm/sup 2/. The specific detectivity (D*) measured at 100 Hz decreased from 2.72/spl times/10/sup 7/ cm/spl middot/Hz/sup 1/2//W for detector without PVDF to 1.71/spl times/10/sup 7/ cm/spl middot/Hz/sup 1/2//W for detector with PVDF thickness of 580 nm. By optimizing the ratio of the specific detectivity (D*) to leakage current, D*/J, the detector with PVDF thickness of 295 nm exhibits the best performance.     

Sintering and dielectric properties of 0.88Al2O3-0.12TiO2 microwave ceramics by glass addition

The microwave characteristics and the microstructures of 0.88Al₂O₃-0.12TiO₂ with various amounts of MgO-CaO-SiO₂-Al₂O₃ (MCAS) glass sintered at different temperatures have been investigated. The sintering temperature can be lowered to 1300 °C by the addition of MCAS glass. The densities, dielectric constants (ε_r) and quality values (Q×f) of the MCAS-added 0.88Al₂O₃-0.12TiO₂ ceramics decrease with the increase of MCAS glass content. The temperature coefficients of the resonant frequency (τ_f) are shifted to more negative values as the MCAS content or the sintering temperatures increase. The change of the crystalline phases of Al₂TiO₅ phase and rutile-TiO₂ phase has profound effects on the microwave dielectric properties of the MCAS-added Al₂O₃-TiO₂ ceramics. As sintered at 1250 °C, 0.88Al₂O₃-0.12TiO₂ ceramics with 2 wt.% MCAS glass addition exists a ε_r value of 8.63, a Q×f value of 9578 and a τ_f value of +5 ppm/°C.     

Photovoltaic properties and stability of I2-doped polyacetylene

Summary Polyacetylene was doped with evaporated iodine (I₂). The characteristics of A1/cis-[CHI_y]_x/Au Schottky barrier solar cell was investigated. It is found that the maximum conversion efficiency is 2.67%. The solar cell parameters, such as open-circuit voltage (V_oc), short-circuit current (J_sc), fill factor (F.F.), and energy conversion efficiency (), were measured under the various incident light intensity. The stability of the cell was also estimated by the variation of J-V curves in argon environment.     

Proton-exchanged Z-cut LiNbO3 waveguides for surfaceacoustic waves

Proton-exchanged (PE) waveguides in Z-cut LiNbO₃ have been fabricated using benzoic acid. Secondary-ion mass spectrometry (SIMS) measurements show that the distribution of hydrogen in the PE Z-cut LiNbO₃ samples exhibits a step-like profile with the diffusion constant D₀ and the activation energy Q of about 2.82×10⁸ μm²/h and 87.76 kJ/mol, respectively. On the other hand, the important parameters for the design of surface acoustic wave (SAW) devices are measured and discussed. The results show that the phase velocity and electromechanical coupling coefficient decrease with the increase of kd, where k is the wavenumber and d is the waveguide depth. The variation of insertion loss becomes saturated at about kd=0.068 with a maximum increase of about 4~5 dB. The temperature coefficient of delay calculated from the frequency change of the output of SAW delay line shows an evident increase in the PE layer. Moreover, the effects of postannealing can result in a restoration of the decreased velocity and an improvement of the insertion loss     

The effect of Bi2O3 compensation during thermal treatment on the crystalline and electrical characteristics of bismuth titanate thin films

Bismuth titanate thin films are deposited on ITO/glass substrates by rf magnetron sputtering at room temperature using a Bi₄Ti₃O₁₂ ceramic target. The deposited Bi₄Ti₃O₁₂ films are annealed in a conventional furnace in ambient air for 10 min at temperatures ranging from 550 to 640 °C. One specimen is annealed in a crucible containing additional Bi₂O₃ compensation powder, while the other specimen is annealed in ambient air. XRD analysis shows that the crystal phases of films annealed with Bi₂O₃ powder are better than those of films annealed without Bi₂O₃ powder. Furthermore, the EDS results reveal that the bismuth weight percentage of the former is higher than that of the latter. SIMS analysis shows that the bismuth decreases near the surface of Bi₄Ti₃O₁₂ film annealed without Bi₂O₃ powder, but reveals a stable distribution throughout the film annealed with Bi₂O₃ powder. These results imply that bismuth is readily evaporated during the thermal treatment process, particularly from the region near the film surface. Finally, the dielectric and polarization properties of the thin films annealed with Bi₂O₃ powder are found to be superior to those of the films annealed in ambient air.