Preparation of Mn2+-Cu+ co-doped P2O5–ZnO–Al2O3 glasses and their red fluorescence properties

To make a Mn²⁺-doped red glass phosphor that can be excited with ultraviolet (UV) light of light-emitting diodes (LEDs), 60P₂O₅-35ZnO-5Al₂O₃-8MnO-xCu₂O glasses (x = 0-1.00) were prepared by a melt-quenching method at 1200-1400°C for 30-180 minutes in atmospheric air, and the redox of Mn and Cu as well as fluorescence properties were investigated. The Mn²⁺ ion was not reduced and oxidized in the melting, quenching, and annealing processes. The valence of Cu in the glasses changed in the order of 0, 1+, and 2+ with the increase in the amount of Cu₂O and in the melting temperature and time. In this study, a 60P₂O₅-35ZnO-5Al₂O₃-8MnO-0.10Cu₂O glass melted at 1250°C for 90 minutes, having the highest Cu⁺ concentration, showed the strongest Mn²⁺ red fluorescence under the UV light at 275 nm. This strong Mn²⁺ red fluorescence has been caused by the energy transfer from excited Cu⁺ ions to Mn²⁺ ions.     

Unperturbed dimension of poly(4-acetoxystyrene) measured in good and theta solvents

In order to obtain the additional data concerning the unperturbed dimension of poly-4-substituted styrene, light scattering measurements are performed on the twenty-two fractions with molecular weight of (0.91–352)·10⁴ of poly(4-acetoxystyrene) in dioxan at 25°C, from which the molecular weight obtained was found easily to be evaluated with the gel permeation chromatography using THF. Phase separation experiments for this polymer indicate that the theta state is attained in isopropyl acetate at 19.7°C and butyl acetate at 26.8°C. By making viscosity measurements at that state, the value of K_Θ is directly evaluated as 5.4·10^?4 dl g^?1. The limiting viscosity number is also obtained in good solvents, THF and dioxan, at 25°C and constants of the Mark-Houwink-Sakurada equation in each solvent are determined. Further, approximately the same K_Θ as above is obtained from these data with the Stockmayer-Fixman plot. The calculated value of steric factor, 2.37, on this polymer may be plausible, compared with those of polyvinylaromatic derivatives.     

Analytical studies of four-inch pipe whip tests under BWR LOCA conditions

The purpose of pipe rupture studies in JAERI is to perform model tests on pipe whip, restraint behavior, jet impingement and jet thrust force, and to establish a computational method for analyzing these phenomena. This report presents the analytical results of 4-inch pipe whip tests under BWR LOCA conditions.Dynamic response analyses were performed using the general-purpose finite element program ADINA. The test pipe was modelled by straight beam elements and the four restraints were modelled by a single truss element. The analytical results were compared with the experimental results. Impact time and maximum total restraint force showed good agreement with experimental results. On the other hand, pipe strain and pipe deflection could not be predicted so well. The reason for this is that the sliding of the restraint during the pipe whip movement cannot be considered in the analyses.     

A reconfigurable VLSI-based double-lens tracking camera

Watching and tracking an object while seeing a much wider view is one of advantages of the eye system. We proposed and developed a tracking camera system that mimics the eyes by using double-lens modules. In the system, a wide view is captured through the wide-lens module, while the target in it is tracked and magnified through the telescopic lens module. Electronic circuits for tracking control are implemented onto the reconfigurable VLSI or FPGA in order to embed the parallelism in the tracking algorithm into the hardware. A successfully developed FPGA-based prototype performs high-speed tracking at the video-rate. This work was present in part at the 12th International Symposium on Artificial Life and Robotics, Oita, Japan, January 25–27, 2007     

Thermal expansion behavior of various aromatic polyimides

The thermal expansion behavior for various aromatic polymides was investigated. Usally polymers, including polyimides, have high thermal expansion coefficients (3–6 × 10^?5 K^?1), compared with metals and ceramics. However, there are some polyimides which have very low thermal expansion coefficients below 1 × 10^?5 K^?1. This property was observed for the polymides obtained from pyromellitic dianhydride or 3,3′ 4,4′-biphenyltetracarboxylic dianhydride and aromatic diamines which were constituted of only benzene rings fused at para positions. It was proposed that their low thermal expansion coefficient related to the linearity in their polymer molecular skeltons.     

Spatial Organization of the Brazilian States with Respect to Human Migration

"Multidimensional scaling technique was applied to the Brazilian migration matrix in order to identify the functional regions of the nation, using the 1970 census data for males. The results obtained from three types of proximity matrices confirmed the key roles of Minas Gerais and Mato Grosso as the core states in addition to Rio de Janeiro and Sao Paulo. Substantial circulation of migrants among the core states runs counter to the popular notion about the Northeastern states as the major source of labor in Rio de Janeiro and Sao Paulo. The Northeast [was] found to consist of three groups of states: Maranhao, Piaui and Ceara showed a stable clustering, but peripherally located, in all configurations; and, the other two groups failed to form persistent regions across configurations. Though limited in scope, the observed attraction of Espirito Santo and Goias violated the widely held negative effect of distance and deserves further investigation."     

Siliconizing of molybdenum plate using Si2Cl6 and some of its properties

Molybdenum plate was siliconized using Si₂Cl₆ as a silicon source, and the siliconizing conditions and some of its properties were examined. The siliconizing of the molybdenum plate began by the deposition here and there of island-like MoSi₂ deposits 4 to 6m thick in the initial stage (after 10 min induction time), and then coalescence of the deposits proceeded to form a uniform MoSi₂ layer all over the molybdenum plate after 30 min siliconizing time. The weight decrease of the siliconized plate by anodic dissolution in 0.2 M sulphuric acid reduced exponentially with increasing thickness of the MOSi₂ layer, and no weight decrease was observed at all above 16m thickness. The sea water corrosion and sea sand abrasion resistivities of the siliconized molybdenum plate increased with increasing siliconizing temperature and Si₂Cl₆ flow rate.     

Removal of nitrogen oxides from air by chemicals-impregnated carbons

Fixation of nitrogen oxides (NO_x) in air onto granular activated carbon impregnated with chemicals was attempted to improve removal efficiency of NO_x by activated carbon adsorption. Nitric oxide (NO) and nitrogen dioxide (NO₂), were tried to remove by a flow test. Fixed-bed adsorption breakthrough curves were obtained when some kinds of carbon were used. The amount adsorbed of NO₂ changed with the amount and kinds of metallic salts impregnated. Chemicals-impregnated carbons were prepared from a commercial activated carbon. Among obtained carbons, the one which showed the highest selectivity for NO_x was chosen, and its performance with the change in humidity was determined. Removal mechanism of NO₂ was estimated, and the carbon impregnated with potassium hydroxide was found to be superior to any other carbon tested. The amount of the adsorbed NO and that produced by the reduction of NO₂ were determined from the breakthrough curves.     

Synthesis and electronic property of platinum nanowire and nanoparticle in mesoporous silica template

Platinum nanowires and nanoparticles were selectively synthesized in mesoporous silicas FSM-16 and HMM-1. The nanowires are 3 nm in diameter and several hundred nm to μm in length with high crystallinity. Pt nanowires and nanoparticles can be isolated by dissolving silica matrix with HF. The Pt wires extracted from organosilica HMM-1 have a nanonecklace structure, while the wires from siliceous FSM-16 have a nanorod structure. The extracted Pt nanoparticles (3 nm in size) on HOPG show the Coulomb staircase phenomena in STM/STS analysis. The mechanism for formation of the Pt nanowires is based on the migration of Pt ions in the mesoporous channels.