ARP-P4: deep analysis of a hybrid SDN ARP-Path/P4Runtime switch

Telecommunication Systems - The Software-Defined Networking (SDN) architecture decouples the control plane from the data plane, but it does not explicitly state where the control should be located....     

Effect of height on the corrosion of steel and galvanized steel in nontropical coastal marine environments

In this study, the behavior of carbon steel and galvanized steel in nontropical coastal marine environments was evaluated. Evaluation was carried out with specimens with dimensions of 10 cm × 10 cm × 0.3 cm. These specimens were exposed to four testing stations (Iquique, Mejillones, Los Vilos, and San Vicente), where racks were installed both at ground level (ground), as well as in the upper zone of electrical transmission towers (tower). In each station, 24 specimens of A36 carbon steel and galvanized steel were placed (12 each). The corrosivity of the environment was measured using the ISO 9223, 9225, and 9226 standards. The specimens were evaluated on-site, monthly, through visual inspection and photographic record. Once withdrawn, the corrosion rate was determined and the corrosion products were analyzed through Raman and Fourier-transform infrared. The results show that, in all cases, the corrosion rate is greater in the tower than on the ground. However, even though the Los Vilos station is located farther from the sea (3,500 vs. ≈500 m), the corrosion rate of steel in the tower is the highest. This is caused by the generation of HCl from the transformation of lepidocrocite into goethite, in the presence of low chloride content, which acidifies the steel/corrosion product interface. In the case of galvanized steel, the corrosion rate is a function of the chloride content in the atmosphere, obtaining an excellent correlation between both parameters.     

Production of 2,3-butanediol from diverse saccharides via fermentation

The present study aimed to evaluate the potential use of whey to produce 2,3-BD via the fermentation of lactose and its monosaccharides, glucose and galactose, in a synthetic culture medium (medium 9, M9) using a modified strain of Escherichia coli K12 MG1655 (E. coli JFR12) at a 0.1 L/L (10 vol%) inoculum ratio, 37 °C, atmospheric pressure, an initial pH 7.4, and 100 rpm for 72 h varying the saccharide concentration from 12.5, 25, and 50 g/L. The 2,3-BD yield was ∼80 % of the theoretical yield using 25 g/L of glucose and lactose, corresponding to 0.38 g/g saccharides at a fermentation time of 48 h (glucose) and 72 h (lactose). However, the 2,3-BD yield was halved (0.19 g/g galactose), fermenting 25 g/L of galactose at 48 h. Taking into account these results, two important conclusions were determined: i) E. coli JFR12 could transform galactose into 2,3-BD although its yield was half of the yield observed with glucose at 48 h; and ii) E. coli JFR12 was as efficient as other natural 2,3-BD producers such as Klebsiella species fermenting lactose. However, the E. coli strain has the advantage of being an innocuous strain. To the best of our knowledge, there is no other study presenting the production of 2,3-BD from galactose and lactose with a genetically modified E. coli strain.     

The lost art of short communications in academia

Scientometrics - Short communications are an integral part of academic journal publishing since they serve as a forum for scholarly debate on recently published journal articles. Their prestige and...     

Tribocorrosion and corrosion behavior of stainless steel coated with DLC films in ethanol with different concentrations of water

There has been a recent increase in both the production and consumption of ethanol due to the numerous environmental advantages that it offers, such as the fact that it can be produced from a variety of renewable materials, for instance corn and cellulose, or it can be obtained from sugarcane bagasse and biomass (2nd and 3rd generation ethanol). The result of this is that nowadays ethanol is widely seen as the dominant biofuel – or as a blend component in gasoline or pure fuel - in many countries.However, one disadvantage of the use of ethanol is the high corrosive behavior that occurs when its hygroscopic properties are exposed to a large number of materials. Xiaoyuan Lou and Preet Singh showed that the increase of water concentration in ethanol induces pitting and metal loss. Diamond-Like Carbon (DLC) films may be a solution to this problem due to the fact that they can be deposited inside tubes, offer good protection levels against corrosion, and reduce the friction coefficient and wear.This paper shows the tribocorrosion and corrosion studies of DLC films deposited on stainless steel grade 304 (SS304) substrates in order to gauge its appropriateness usage in the construction of pipelines and fuel storage tanks. The surface morphology was analyzed before and after 14 days of immersion. The tribocorrosion, friction coefficient, and wear rate were studied in ethanol to see the effects of water concentration. The films showed good adherence to the substrates. Corrosion and tribocorrosion results showed that for bare Stainless Steel 304 the increase of the water content increases the corrosion and the friction coefficient. DLC coated samples presented few points of delamination, and the friction coefficient and open circuit potentials were very low compared with the bare sample which was water concentration independent.     

Online model-based diagnosis to support autonomous operation of an advanced life support system

This article describes methods for online model-based diagnosis of subsystems of the advanced life support system (ALS). The diagnosis methodology is tailored to detect, isolate, and identify faults in components of the system quickly so that fault-adaptive control techniques can be applied to maintain system operation without interruption. We describe the components of our hybrid modeling scheme and the diagnosis methodology, and then demonstrate the effectiveness of this methodology by building a detailed model of the reverse osmosis (RO) system of the water recovery system (WRS) of the ALS. This model is validated with real data collected from an experimental testbed at NASA JSC. A number of diagnosis experiments run on simulated faulty data are presented and the results are discussed.     

On the association between poly(vinyl alcohol) and sodium dodecyl sulfate and its effect on liquid–liquid interfacial tension: A mathematical model

Association between poly(vinyl alcohol-co-vinyl acetate) copolymer (PVA) and sodium dodecyl sulfate (SDS) was studied experimentally and theoretically. It was found that, for the ethyl acetate-aqueous phase interface in which PVA was previously adsorbed, the interfacial tension (γ) increases abruptly to a maximum and then exhibits a relatively mild decay with the addition of SDS to the aqueous phase. The theoretical results indicate that vinyl acetate (VAc) segments determine γ. However, for relatively low concentrations of SDS (C_SDS), this latter plays a major role because through its association with the VAc segments it modulates the extent to which PVA is adsorbed at the interface, indirectly determining the value of γ. As C_SDS approaches to the CMC value for SDS, its influence on γ decreases because SDS tends to self-assembly rather than associates with VAc. These model predictions are consistent with experimental findings reported in the literature.     

Radiolabeled Polymeric Nanoconstructs Loaded with Docetaxel and Curcumin for Cancer Combinatorial Therapy and Nuclear Imaging

Growing evidence suggests that multifaceted diseases as cancer can be effectively tackled by hitting simultaneously different biological targets and monitoring patient‐specific responses. Combinatorial therapies, relying on the administration of two or more molecules with different cytotoxic mechanisms, are rapidly progressing in the clinic. Here, 100 nm spherical polymeric nanoconstructs (SPNs) are proposed for the combinatorial treatment of tumors by codelivering a potent antimitotic drug—docetaxel (DTXL)—and a broad spectrum anti‐inflammatory molecule—curcumin (CURC). In vitro, SPNs loaded with DTXL and CURC induce a threefold decrease in IC₅₀ as compared to DTXL‐loaded SPNs. This synergic antitumor effect is also significant in mouse models of glioblastoma multiforme, where, after 22 d of treatment, the combinatorial approach leads to complete disease regression. At 90 d post‐treatment initiation, mice injected with DTXL + CURC SPNs have a 100% survival, whereas only 50% of the DTXL SPN treated mice survive. SPNs are also labeled with radioactive ⁶⁴Cu(DOTA) molecules to document, via PET imaging, the progressive tumor mass shrinkage. Sensitization of DTXL by CURC is associated with NF‐κB downregulation and increased apoptosis. These theranostic nanoconstructs could be used for combinatorial treatment and assessment of therapeutic efficacy in other malignancies.     

Friction stir welding of duplex stainless steels

Duplex stainless steels are successful in a variety of applications such as the food industry, petrochemicals and plants for desalination of seawater, where high corrosion resistance and high mechanical strength are required. However, the beneficial microstructure may change during fusion welding steps, and it can compromise the performance of these materials. Friction stir welding is a solid-state process avoiding typical problems concerning solidification such as solidification cracks, liquation and segregation of alloying elements. Superduplex stainless steels can avoid unbalanced proportions of ferrite and austenite, formation of secondary deleterious phases and grain growth of ferrite in the heat-affected zone. Consolidated friction stir welded joints with full penetration 6 mm thick were obtained for UNS S32101 and S32205 duplex and S32750 and S32760 superduplex stainless steels. The friction stir welds were submitted to tensile tests indicating an improvement of strength in welded joints, showing increased yield and tensile strength for all studied cases. Regarding the microstructural characterization, an outstanding grain refinement was observed in the welded joint, achieving grain sizes as small as 1 μm. This refinement was associated with the combination of microstructural restoration mechanisms in the dual-phase microstructure promoted by severe deformation associated with a high temperature during the welding process.