Centrifugally spun carbon fibers prepared from aqueous poly(vinylpyrrolidone) solutions as binder-free anodes in lithium-ion batteries

Aqueous solutions of poly(vinylpyrrolidone) (PVP) of various concentrations (20, 25, and 28 wt%) were successfully spun into fibers by centrifugal spinning. The pristine PVP fibers were annealed and carbonized to produce flexible carbon fibers for use as binder-free anodes in lithium-ion batteries. These flexible carbon fibers were prepared by developing a novel three-step heat treatment to reduce the residual stresses in the pristine PVP precursor fibers, and to prevent fiber degradation during carbonization. The thermogravimetric analysis data showed that the annealed fibers yielded a residual mass percentage of 36.0% while the pristine PVP fibers suffered a higher mass loss and only retained 26.5% of original mass above 450 °C (under nitrogen). The electrochemical performance of the carbon-fiber anodes was evaluated by conducting galvanostatic charge/discharge, rate performance, and cycle voltammetry experiments. The 20, 25, and 28 wt% derived binder-free anodes delivered specific charge capacities of 205, 189, and 275 mAh g⁻¹, respectively, after the first cycle at a current density of 100 mA g⁻¹. The results obtained in this work indicate that a feasible pathway towards a large-scale production of carbon-fiber anodes from a 100% aqueous solution can be achieved via centrifugal spinning and subsequent heat treatment.     

Impact strength elastomer composites based on polystyrene components separated from waste electrical and electronic equipment

The reuse of plastic components of waste electrical and electronic equipment (WEEE) is an important concern both for environmental issues and to preserve the material resources, with minimum energy consumption. Considering that polystyrene fraction was reported as approximate 80% of the total amount of WEEE plastic, this article aims to evaluate the recycling of this fraction, without separation by components, by melt compounding with styrene-butadiene block-copolymer (SBS) and hydrogenated and maleinized SBS, the blend of the two elastomers acting both as an impact modifier and compatibilizer. The composites are characterized by mechanical analysis, impact tests, dynamic mechanical analysis, differential scanning calorimetry, thermogravimetric analysis, scanning electron microscopy, energy dispersive X-ray analysis, and X-ray diffraction. The recycling conditions of the polystyrene fraction as composites without eliminating the WEEE additives for improved UV and flame resistance, with physical mechanical properties comparable to those of high-impact polystyrene resulted from the study. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48329.     

One-step synthesis of graphene supported platinum nanoparticles as electrocatalyst for PEM fuel cells

Here in, we describe an ultrafast, single-step microwave irradiation route (MW) to prepare graphene supported Pt nanoparticles, during which the small Pt nanoparticles are distributed uniformly on a reduced graphene oxide surface. This route provides evident advantages namely low cost, easiness, low time consuming and high yield in comparison to actual chemical methods to develop efficient Pt/rGO catalyst with Pt content close to state-of-the-art commercial composition. The structure and composition of prepared samples have been studied by specific techniques, while the electrocatalytic stability has been studied using ex-situ and in-situ measurements. High performance and electrochemically stable catalyst for PEM fuel cells was developed using the sample with highest loading and good dispersion. The fabricated Pt-rGO-based MEA was investigated for durability under fuel starvation in comparison with commercial Pt/C-based MEA. The electrocatalytic activity was investigated and the electrochemical response revealed the higher stability during accelerated degradation test under fuel starvation in comparison with commercial Pt/C. This study promotes the applicability of described preparation method to noble or transition metal nanoparticles embedded on graphene-based materials.     

Self-doped N-propansulfonic acid polyaniline-polyethylene terephthalate film used as active sensor element for humidity or gas detection

In this work, we report the fabrication of sensors’ element for humidity or gases, prepared by in situ polymerization of aniline N-propansulfonic acid using ammonium persulfate in acidic medium. The polymer is being used in the form of powder or deposited in multiple layers onto the PET film. Various techniques including Fourier Transform infrared (FTIR), ultraviolet-–visible spectroscopy (UV–vis), X-ray diffraction (XRD) and scanning electron microscopy (SEM) were employed to characterize the as-prepared sensing materials. The film has been tested for humidity influence, where the significant variations in electrical characteristics were observed, suggesting its usefulness for humidity sensors. Also, for different organic and inorganic gases, a relatively low operating temperature and important sensitivity were observed that indicate its applicability as an active element for general gases sensors. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 47743.     

Long Range Self‐Assembly of Polythiophene Breath Figures: Optical and Morphological Characterization

Large‐area, device relevant sized microporous thin films are formed with commercially available polythiophenes by the breath figure technique, a water‐assisted micropatterning method, with such semitransparent thin films exhibiting periodicity and uniformity dictated by the length of the polymer side chain. Compared to drop‐casted thin films, the microporous thin films exhibit increased crystallinity due to stronger packing of the polymer inside the honeycomb frame.     

Rhombellation: a builder for multi-shell clusters

Rhombellanes are mathematical structures, proposed by us in 2017; they may appear both in periodic crystals or in finite structures. The simplest rhombellane is rbl.5 or K_2.3, the complete bipartite graph. In this paper, rhombellation operation is iteratively applied on three classes of structures: cube, tori and cubic pcu-network, respectively. The structural topological parameters are detailed.     

Transient Pressure and Temperature Field Measurements in a Lightly Loaded Circumferential Groove Journal Bearing from Startup to Steady-State Thermal Stabilization

The fluid film pressure and temperature fields have been measured simultaneously under laboratory conditions at one land of a circumferential groove journal bearing (CGJB), together with friction torque and oil flow rate, during a time span from stand-still startup to the development of a thermally stabilized steady operating regime.A very fine measurement grid—that is, 216 pressure and 180 temperature points spread across the axial and circumferential directions—has been obtained by joining and synchronizing measurements from separate test runs while rigorously re-creating the test conditions.The study confirmed that the pressure field is established faster than the temperature field, that film rupture occurs both from cavitation nuclei downstream the minimum film thickness and through air ingestion from the environment. Furthermore, the high pressures in the convergent zone stabilize relatively quickly, whereas the low pressures in the divergent zone cavitated region require a longer time to stabilize. The cavitated region reverse flow appearance has been identified thermally through upstream-oriented isotherms. This study is the first to present the transient evolutions of pressure and temperature fields.     

Rheological Properties of Honey from Burkina Faso: Loss Modulus and Complex Viscosity Modeling

This study evaluated the rheological behavior of Burkina Faso honey and the use of exponential and polynomial models to predict the influence of chemical composition and temperature on the viscoelastic parameters: complex viscosity (η*) and loss modulus (G’’). Samples were first characterized by evaluating: water activity, 5-hydroxy methyl furfural, sugars (fructose, glucose, and sucrose), electrical conductivity, moisture, and color. Dynamic rheological properties were obtained at different temperatures (5, 10, 15, 20, 25, 30, and 40°C). All the honeys displayed Newtonian behavior. Complex viscosity and loss modulus can be predicted based on the chemical composition and temperature using polynomial models (R² > 98.00%).