Effect of oxidants on microalgal flocculation

The effects of chlorine, ozone and chlorine dioxide on Scenedesmus sp. cultures were studied. Algal cell viability and chlorophyll concentration decreased, and the concentration of dissolved organic substances increased with increasing applied oxidant concentration. Pretreatment with chlorine dioxide (1, 3 or 5 mg l⁻¹) or ozone (2.6, 4.6 or 8.1 mg l⁻¹) on algal cultures enhanced algal flocculation with alum, while prechlorination with 10 or 20 mg l⁻¹ increased the required dosage of alum by 15%. Scanning electron micrographs of oxidized cells revealed drastically adverse effects upon the cell surface architecture: in addition to the oxidation of noncellular organic materials, the oxidants damaged both cell surface structures and intracellular components. A model explaining the effects of the different oxidants on microalgal flocculation is suggested.     

Water remediation by micelle-clay system: case study for tetracycline and sulfonamide antibiotics

Removal of tetracycline and sulfonamide antibiotics from water by micelles pre-adsorbed on montmorillonite was studied. Micelles of benzyldimethylhexadecylammonium (BDMHDA) were used. Batch experiments demonstrated that the micelle-clay complexes (1% w/w) removed 96-99.9% of antibiotics from their water solutions containing from 5 to 50 mg/L of pharmaceuticals. Column filters (25 cm) made of a mixture of quartz sand and BDMHDA micelle-clay complex at 100:1 w/w ratio removed 94-99.9% of above pharmaceuticals from initial solutions containing 10mg/L and 89% of sulfamethizole from an initial solution containing 10 microg/L of this antibiotic. These filters were also very efficient in the removal of antibiotics in the presence of dissolved soil organic matter removing 89-99% of tetracycline and sulfamethizol from initial solutions containing 10 mg/L of antibiotic in the presence of 8 mg/L of humic acid, or 9 mg/L of fulvic acid. These data indicate that micelle-clay complexes are very efficient for water purification from tetracycline and sulfonamide antibiotics.     

Flexible Blade‐Coated Multicolor Polymer Light‐Emitting Diodes for Optoelectronic Sensors

A method to print two materials of different functionality during the same printing step is presented. In printed electronics, devices are built layer by layer and conventionally only one type of material is deposited in one pass. Here, the challenges involving printing of two emissive materials to form polymer light‐emitting diodes (PLEDs) that emit light of different wavelengths without any significant changes in the device characteristics are described. The surface‐energy‐patterning technique is utilized to print materials in regions of interest. This technique proves beneficial in reducing the amount of ink used during blade coating and improving the reproducibility of printed films. A variety of colors (green, red, and near‐infrared) are demonstrated and characterized. This is the first known attempt to print multiple materials by blade coating. These devices are further used in conjunction with a commercially available photodiode to perform blood oxygenation measurements on the wrist, where common accessories are worn. Prior to actual application, the threshold conditions for each color are discussed, in order to acquire a stable and reproducible photoplethysmogram (PPG) signal. Finally, based on the conditions, PPG and oxygenation measurements are successfully performed on the wrist with green and red PLEDs.     

Surface Oxidation as a Cause of High Open‐Circuit Voltage in CdSe ETA Solar Cells

TiO₂/CdSe/CuSCN extremely thin absorber (ETA) solar cells are found to give relatively high values of open‐circuit voltage (>0.8 V) but low currents upon annealing the cadmium selenide (CdSe) in air (500 ºC). Annealing in N₂ produces much lower photovoltages and slightly lower photocurrents. Band structure measurements show differences between the two annealing regimes that, however, appear to favor the N₂‐annealed CdSe. On the other hand, chemically resolved electrical measurements (CREM) of the cells reveal marked differences in photo‐induced charge trapping, in particular at absorber grain boundaries of the air versus N₂‐annealed systems, correlated with the formation of Cd–O species at the CdSe surface. Using transient absorption and photovoltage decay, pronounced lifetime differences are also observed, in agreement with the strong suppression of charge recombination. The results point to a multiple role of grain surface‐oxidation, which both impedes electron injection from the CdSe to the TiO_2, but, much more significantly, enhances hole injection to the CuSCN via passivation of hole traps that act as efficient recombination centers.     

Harnessing “Click”‐Type Chemistry for the Preparation of Novel Electronic Materials

Sequence‐independent or “click”‐type chemistry is applied for the preparation of novel π‐conjugated oligomers. A variety of bi‐functional monomers for Wittig–Horner olefination are developed and applied in a sequential protection–deprotection process for the preparation of structurally similar π‐conjugated oligomers. Selected oligomers are incorporated as the organic semiconductors in light‐emitting diodes and a field‐effect transistor, demonstrating the potential of the approach.     

Interface Modifications of InAs Quantum‐Dots Solids and their Effects on FET Performance

InAs nanocrystals field‐effect transistors with an ON/OFF ratio of 10⁵ are reported. By tailoring the interface regions in the active layer step‐by‐step, the evolution of the ON/OFF ratio can be followed from approximately 5 all the way to around 10⁵. The formation of a semiconducting solid from colloidal nanocrystals is achieved through targeted design of the nanocrystal–nanocrystal interaction. The manipulation characteristics of the nanocrystal interfaces include the matrix surrounding the inorganic core, the interparticle distance, and the order of nanocrystals in the 3D array. Through careful analysis of device characteristics following each treatment, the effect of each on the physical properties of the films are able to be verified. The enhanced performance is related to interparticle spacing, reduction in sub‐gap states, and better electronic order (lower σ parameter). Films with enhanced charge transport qualities retain their quantum‐confined characteristics throughout the procedure, thus making them useful for optoelectronic applications.