Microwave hybrid fast sintering of red clay ceramics

This work aimed to examine the performance of the hybrid sintering of clay ceramic in a microwave furnace, compared to the sintering process in a conventional furnace. The raw materials were subjected to X-ray fluorescence, loss on ignition (LOI), X-ray diffraction, particle size distribution, real specific mass, and thermogravimetric analyses. The red clay ceramic mass was prepared, extruded, pre-sintered in a conventional furnace at 600°C/60 min, and sintered at temperatures between 700 °C and 1100 °C. The sintering conventional (resistive oven) was carried out for 60 min with a heating rate of 10°C/min. In the microwave furnace, the sintering times were 5, 10, and 15 min, with a heating rate of 50°C/min, with a sintering chamber coated with silicon carbide (susceptor). The sintered specimens were characterized according to linear shrinkage, water absorption, apparent porosity, apparent specific mass, X-ray diffraction, Raman spectroscopy analysis, spectroscopy analysis in the ultraviolet and visible regions, microhardness, and scanning electron microscopy. The results showed that microwave sintering promoted an increase in the microhardness and apparent specific mass, and reduction in water absorption and apparent porosity values, due to greater densification in the microstructure. The best results occurred for specimens sintered at 1100°C.     

Study of the influence of notch radii and temperature on the probability of failure: A methodology to perform a combined assessment

The fracture assessment of notched components based on cracked components approaches leads to over‐conservative failure predictions. In the research literature, several approaches are proposed to overcome this problem using an apparent fracture toughness, . Nevertheless, most of these approaches are based on deterministic assumptions despite the large and variable scatter exhibited by for different notch radii (ρ) or temperatures (T). This paper proposes a methodology for deriving a probabilistic field including the effect of temperature on the failure of notched components. First, the theory of critical distances is applied to transform each apparent fracture toughness into the equivalent fracture toughness for ρ = 0. Then, the temperature is supposed to act as a scale effect in the Weibull cumulative distribution function of the equivalent fracture toughness, and the corresponding scale effect function is derived. Finally, the applicability of the proposed methodology is illustrated by an example using two ferritic‐pearlitic steels: S275JR and S355J2.     

Effect of Functionalization Synthesis Type of Amino-MCM-41 Mesoporous Silica Nanoparticles on Its RB5 Adsorption Capacity and Kinetics

Silicon - This study was undertaken to evaluate the adsorption of Reactive Black 5 dye (RB5), in aqueous solution, onto MCM-41 mesoporous silica nanoparticles (MSNs) functionalized with...     

Short SiC fiber/Ti3SiC2 MAX phase composites: Fabrication and creep evaluation

The compressive creep of silicon carbide fiber reinforced Ti₃SiC₂ MAX phase with both fine and coarse microstructure was investigated in the temperature range of 1000-1300°C. Comparison of only steady-state creep was done to understand the response of fabricated composite materials toward creep deformation. It was demonstrated that the fibers are more effective in reducing the creep rates for the coarse microstructure by an increase in activation energy compared to the variant with a finer microstructure, being partly a result of the enhanced creep rates for the microstructure with larger grain size. Grain boundary sliding along with fiber fracture appears to be the main creep mechanism for most of the tested temperature range. However, there are indications for a changed creep mechanism for the fine microstructure for the lowest testing temperature. Local pores are formed to accommodate differences in strain related to creeping matrix and predominantly elastically deformed fibers during creep. Microstructural analysis was done on the material before and after creep to understand the deformation mechanics.     

Rare Titin (TTN) Variants in Diseases Associated with Sudden Cardiac Death

A leading cause of death in western countries is sudden cardiac death, and can be associated with genetic disease. Next-generation sequencing has allowed thorough analysis of genes associated with this entity, including, most recently, titin. We aimed to identify potentially pathogenic genetic variants in titin. A total of 1126 samples were analyzed using a custom sequencing panel including major genes related to sudden cardiac death. Our cohort was divided into three groups: 432 cases from patients with cardiomyopathies, 130 cases from patients with channelopathies, and 564 post-mortem samples from individuals showing anatomical healthy hearts and non-conclusive causes of death after comprehensive autopsy. None of the patients included had definite pathogenic variants in the genes analyzed by our custom cardio-panel. Retrospective analysis comparing the in-house database and available public databases also was performed. We identified 554 rare variants in titin, 282 of which were novel. Seven were previously reported as pathogenic. Of these 554 variants, 493 were missense variants, 233 of which were novel. Of all variants identified, 399 were unique and 155 were identified at least twice. No definite pathogenic variants were identified in any of genes analyzed. We identified rare, mostly novel, titin variants that seem to play a potentially pathogenic role in sudden cardiac death. Additional studies should be performed to clarify the role of these variants in sudden cardiac death.