Effects of Winding Attachment Positions on Output Characteristics of Flux‐Modulating Synchronous Machines

The flux‐modulating synchronous machine (FMSM) is a new type of multipole SM with nonoverlapping concentrated armature and field windings on the stator. This paper compares the output characteristics of two FMSMs through finite element analysis (FEA) and experiments. In both of the FMSMs, the attachment positions of the armature and field windings are swapped. To determine the reason for the discrepancies in their output characteristics, unsaturated inductances were calculated using a d‐‐q equivalent circuit. In addition, the calculated results of the inductances were confirmed through a visualization of the leakage fluxes using FEA. The results of the study show that the synchronous inductance can be reduced by attaching the armature winding to the air‐gap side of the stator teeth and that the reduction leads to an increase in output power.     

Effects of vasodilators and perfusion pressure on coronary flow and simultaneous release of nitric oxide from guinea pig isolated hearts

OBJECTIVE: The aims were to validate the use of a direct reading NO electrode, to compare the effects of diverse acting drugs on altering coronary flow (CF) and NO release, and to examine the effects of altered perfusion pressure on flow-induced changes in NO concentration [NO] in the hemoglobin free effluent of guinea pig isolated hearts. METHODS: Hearts were isolated and perfused initially at a constant perfusion pressure (55 mmHg) with a modified Krebs-Ringer's solution equilibrated with 97% O2 and 3% CO2 at 37 degrees C. Heart rate, left ventricular pressure, CF, and effluent pH, pCO2, pO2, and NO generated current were monitored continuously on-line. Effluent was sampled for L-citrulline. Percent O2 extraction and O2 consumption were calculated. [NO] was quantitated with a sensitive amperometric sensor (sensitivity > or = 1 nmol/l approximately 3 pA) and a selective gas permeable membrane. RESULTS: The electrode was not sensitive to changes in solution pO2, flow, or pressure. The electrode was sensitive to pCO2 (-0.50 nmol/l/mmHg) and temperature (+24.5 nmol/l/degree C), so coronary effluent pCO2 was measured to compensate for a small decrease in pCO2 that occurred with an increase in coronary flow, and effluent temperature was rigidly controlled. Serotonin, bradykinin, and nitroprusside increased NO release along with CF, whereas nifedipine, butanedione monoxime, zaprinast, and bimakalim comparably increased CF but did not increase [NO] or NO release. Increases in CF (ml/g/min) and NO release (pmol/g/min), respectively, were 5.0 +/- 1 and 100 +/- 17 for 1 mumol/l serotonin, 7.5 +/- 1 and 148 +/- 18 for 100 nmol/l bradykinin, and 7.8 +/- 1 and 173 +/- 28 for 100 mumol/l nitroprusside. The increases in effluent NO by bradykinin were proportional to the increases in L-citrulline. Tetraethylammonium decreased CF, but did not change NO release, indomethacin changed neither CF nor NO release, and NG-nitro-L-arginine methyl ester (L-NAME) reduced CF by 2.6 +/- 1 ml/g/min and NO release by 25 +/- 8 pmol/g/min. An increase of CF of 8.0 +/- 0.3 ml/g/min, produced by increasing perfusion pressure from 25 to 90 mmHg, increased [NO] by 30 +/- 4 nmol/l; L-NAME but did not reduce the pressure-induced increase in CF, but reduced the increase in [NO] to 10 +/- 5 nmol/l. CONCLUSIONS: This study demonstrates in intact hearts real-time release of NO by several vasodilator drugs and by pressure-induced increases in flow (shear stress) and attenuation of these effects by L-NAME.     

Simulation of Strength Distribution in Ground Ceramics by Incorporating Residual Stress Effect

Strength of ground ceramics may be affected by residual stress as well as surface flaws induced by grinding. Strength prediction for ground ceramics is convenient for mechanical design of ceramic components. In this article, a numerical procedure based on fracture mechanics was proposed to estimate strength distribution of ground ceramics by considering grinding-induced residual stress. Bending strength and residual stress of ground ceramics were measured for three grinding-conditions. By comparison of simulated results with experimental ones, it was revealed that strength characteristics in experiments were well simulated by using the proposed procedure.     

Continuous hydrolysis of olive oil by lipase in microporous hydrophobic membrane bioreactor

Continuous hydrolysis of olive oil byCandida cylindracea’s lipase was studied in a microporous hydrophobic membrane bioreactor. Olive oil and buffer solution, fed continuously through two compartments partitioned by membrane, caused reaction at the interface of lipase-adsorbed membrane and buffer solution. Fatty acid was obtained in a single phase without being mixed with components of other phases. At all mean residence times, countercurrent flow mode was superior to cocurrent one. The lipase was adsorbed onto the membrane, and its adsorption was suggested to be partially specific from the experiments with enzymes having various levels of purity. The percent hydrolysis depended hyperbolically on the interfacial enzyme concentration. The hydrolysis seemed to be limited by diffusion of fat or fatty acid through the micropores of the membrane at higher interfacial enzyme concentrations. The lipase was stabilized significantly by glycerol added to the buffer solution. Satisfactory performance of the membrane bioreactor was obtained in a longterm continuous operation which lasted for 24 days by feeding buffer-glycerol (18.0%) solution over the adsorbed lipase. The operational half-life of the adsorbed enzyme was 15 days at 40 C.     

Preparation of one-dimensional polymer films by modification of a hydroxymethylbenzene self-assembled monolayer on iron with alkyltriethoxysilanes for preventing iron corrosion

A self-assembled monolayer (SAM) of p-hydroxymethylbenzene HOCH₂C₆H₄ - (HOMB) moiety adsorbed on iron by the formation of a covalent bond between carbon and iron atoms was prepared by electrochemical derivatization of an iron electrode with p-hydroxymethylbenzenediazonium tetrafluoroborate HOCH₂C₆H₄N₂BF₄. The electrode covered with the HOMB SAM was modified with alkyltriethoxysilanes C_nH_2n+1Si(OC₂H₅)₃ (C_nTES, n = 8 or 18) to prepare a film of one-dimensional polymer. The protective ability of the polymer film was determined by polarization measurement of the covered electrode in an aerated 0.5 M NaCl solution. The ability was enhanced by modification of the HOMB SAM with C_nTES markedly. The iron surface coated with the one-dimensional polymer film of the HOMB SAM modified with C₈TES was characterized by contact angle measurement and FTIR reflection and X-ray photoelectron spectroscopies. The persistence in the protective ability of the polymer film against iron corrosion in 0.5 M NaCl may be associated with the strong adsorption via the covalent bond, revealed by electron-probe microanalysis.     

Radiation detector made of a high-quality polycrystalline diamond

Radiation detector was made of a high-quality CVD polycrystalline diamond composed of frost column like structure diamond grains, and induced charge distribution spectra and drift velocities were measured by using alpha particles. As a result, the CVD polycrystalline achieved maximum induced charge of 83% of HP/HT type IIa diamond. Moreover, the CVD crystal had lower charge loss on electrons compared with the HP/HT type IIa diamond. Drift velocities of electrons and holes were v_e = 7.7 × 10⁴ and v_h = 7.3 × 10⁴cm/s at an electric field of 20 kV/cm, respectively. In addition, response function measurement for 14 MeV neutrons was carried out.     

Direct digital design of computed torque controllers

Direct digital design of computed torque controllers for a robot manipulator is discussed in this article. A simple discrete-time model of the robot manipulator obtained by Euler's method is used for the design. Taking account of computation delay in the digital processor, we propose predictor-based designs of the PD and PID type controllers. The PID-type controller is designed based on a modified version of the discrete-time integral controller proposed by Mita. For both controllers, the feedback gains can be determined easily by using simple formulas. A simulation example is presented to illustrate the relevance of the proposed designs and the robustness of PID-type controller against physical parameter variations. © 1994 John Wiley & Sons, Inc.