New fault locating system for air-insulated substations usingoptical current detector

The authors present the basic philosophy, construction, design features, and test results of a new fault locating system. This fault locating system helps to shorten the time required for restoration of service after the occurrence of a busbar fault in an air-insulated distribution substation. Recent optical and electronic technologies allow the design of a highly accurate and compact fault locating system which consists of optical current detectors using the Faraday effect and a fault locating processor using a digital data processing technique. The fault location is carried out by discriminating between the directions of zero-sequence currents. Through various tests and field operations, it has been confirmed that the system has sufficient performance for practical applications     

Beam test of the CsI(Tl) calorimeter for the BELLE detector at the KEK-B factory

We studied the performance of a prototype electromagnetic calorimeter for the BELLE detector at the KEK proton synchrotron for an energy range of 0.25–3.5 GeV. The prototype consisted of an array of 6 × 5 CsI(Tl) crystals with 30 cm length (16.2 radiation lengths) and about 6 cm × 6 cm cross section. The scintillation light of each CsI(Tl) crystal was read out by two large-area PIN photodiodes and charge-sensitive preamplifiers attached at the rear face of the crystal. We measured the energy and position resolution for electrons and the e/π separation for two sets of matrix configurations: one corresponded to the center and the other to the edge of the barrel calorimeter. The overall performance measured by the test proves that the prototype calorimeter is satisfactory for the use in the BELLE detector.     

Rubber-modified epoxy resins containing high functionality acrylic elastomers

The effect of the functionality of n-butylacrylate/acrylic acid copolymers upon the impact resistance of epoxy resins modified with these rubbery copolymers as a second phase was investigated using a high speed tensile test and scanning electron microscopy. It was found that an optimum functionality of copolymer existed for maximum impact resistance. This optimum value was the result of the competition between the amount of rubber–matrix reaction, an increases in which tended to increase toughness, and solubility of the rubber in the epoxy matrix, which eventually decreased toughness.     

Predictors of user perceptions of web recommender systems: How the basis for generating experience and search product recommendations affects user responses

One critical question suggested by Web 2.0 is as follows: When is it better to leverage the knowledge of other users vs. rely on the product characteristic-based metrics for online product recommenders? Three recent and notable changes of recommender systems have been as follows: (1) a shift from characteristic-based recommendation algorithms to social-based recommendation algorithms; (2) an increase in the number of dimensions on which algorithms are based; and (3) availability of products that cannot be examined for quality before purchase. The combination of these elements is affecting users’ perceptions and attitudes regarding recommender systems and the products recommended by them, but the psychological effects of these trends remain unexplored. The current study empirically examines the effects of these elements, using a 2 (recommendation approach: content-based vs. collaborative-based, within)×2 (dimensions used to generate recommendations: 6 vs. 30, between)×2 (product type: experience products (fragrances) vs. search products (rugs), between) Web-based study (N=80). Participants were told that they would use two recommender systems distinguished by recommendation approach (in fact, the recommendations were identical). There were no substantive main effects, but all three variables exhibited two-way interactions, indicating that design strategies must be grounded in a multi-dimensional understanding of these variables. The implications of this research for the psychology and design of recommender systems are presented.     

Analysis of PD-generated SF/sub 6/ decomposition gases adsorbed on carbon nanotubes

Chemical byproducts analysis has been recognized as a powerful diagnosis method for SF₆ gas-insulated switchgear (GIS). The authors have previously demonstrated that a carbon nanotube (CNT) gas sensor could detect partial discharge (PD) generated in SF₆ gas. However, PD-generated decomposition gas species, which were responsible for the CNT gas sensor response, have not been identified yet. In this paper, two kinds of experiments were conducted in order to identify the responsible decomposition gas species. At first, the decomposition gas molecules adsorbed on CNTs were analyzed by Fourier transformation infrared (FTIR) spectroscopy. FTIR absorbance was observed around 735 cm^-1 after CNTs were exposed to PD generated in SF₆. In the second experiment, the CNT gas sensor responses to typical SF₆ decomposition products (HF and SF₄) were examined. The CNT gas sensor responded to these gases in the same way as to PD generated in SF₆. SF₄ response was larger than HF response. Based on these results, SF ₄ and SOF₂ emerged as candidates for the responsible decomposition gases. Electrochemical interactions between adsorbed gas molecules and CNT were discussed based on theoretical predictions of molecular orbital calculations. The calculation results suggested that both of SOF₂ and SF₄ could increase the CNT gas sensor conductance     

Demonstration of a fully spatial coherent X-ray laser at 13.9 nm

We have recently reported the successful development of a fully coherent X-ray laser (XRL) at 13.9 nm by an oscillator-amplifier configuration with two targets. In the experiment, a seed XRL beam from the first target is injected into a plasma amplifier at the second target. The observed XRL beam has full spatial coherence and 0.2 mrad of nearly diffraction-limited divergence. In order to improve the output fluence, the amplification properties of the XRL beam have been investigated using various plasma lengths of the second amplifier target. The output energy has been improved by a factor of ten, increasing the length of the gain region to 10 mm, resulting in about 0.2 /spl mu/J of output energy.     

Polyphenols Extracted from Black Tea (Camellia sinensis) Residue by Hot‐Compressed Water and Their Inhibitory Effect on Pancreatic Lipase in vitro

Abstract: Polyphenols, retained in black tea wastes following the commercial production of tea beverages, represent an underutilized resource. The purpose of this study was to investigate the potential use of hot‐compressed water (HCW) for the extraction of pancreatic lipase‐inhibiting polyphenols from black tea residues. Black tea residues were treated with HCW at 10 °C intervals, from 100 to 200 °C. The resulting extracts were analyzed using high‐performance liquid chromatography‐mass spectrometry and assayed to determine their inhibitory effect on pancreatic lipase activity in vitro. Four theaflavins (TF), 5 catechins, 2 quercetin glycosides, quinic acid, gallic acid, and caffeine were identified. The total polyphenol content of extracts increased with increasing temperature but lipase inhibitors (TF, theaflavin 3‐O‐gallate, theaflavin 3′‐O‐gallate, theaflavin 3,3′‐O‐gallate, epigallocatechin gallate, and epicatechin gallate) decreased over 150 °C. All extracts inhibited pancreatic lipase but extracts obtained at 100 to 140 °C showed the greatest lipase inhibition (IC₅₀s of 0.9 to 1.3 μg/mL), consistent with the optimal extraction of TFs and catechins except catechin by HCW between 130 and 150 °C. HCW can be used to extract pancreatic lipase‐inhibiting polyphenols from black tea waste. These extracts have potential uses, as dietary supplements and medications, for the prevention and treatment of obesity. Practical Application: Active forms of lipase inhibitors can be recovered from black tea residues. They could be used as dietary supplements or medications.     

Sensorless point-to-point control for a musculoskeletal tendon-driven manipulator: analysis of a two-DOF planar system with six tendons

Tendon-driven robot utilizes only tensile force (i.e. tension) for motion generation. Therefore, a redundant actuation is characteristically necessary, and then it yields the internal force among tendons. Given the internal force for balance at a desired posture, the musculoskeletal tendon-driven manipulator has the inherent possibility of point-to-point position control without any sensory feedback. However, the motion convergence is strongly governed by the arrangement of tendons.This study analyzes the mathematical conditions of convergence for this sensorless position control by use of a Lyapunov function. Subsequently, targeting the two-link musculoskeletal structure with six tendons, the sufficient conditions for the convergence at desired posture are further defined by employing an approximation of the tendon-length based on a Taylor expansion. Finally, the convergent conditions are verified through simulation and validated via experimental results.     

Influence of the introduction of flexible alkyl chains on the thermal behavior and mechanical properties of mesogenic epoxy thermosets

A mesogenic epoxy resin (DGETAM) was cured with a series of curing agents having different lengths of long alkyl chain (nBAB, n = 4, 8, 12). Properties of the curings were compared with those of the DGEBA cured with the same curing agents revealing the achievement of a balance between certain levels of thermal properties and excellent mechanical properties. Moreover, some curing systems were prepared with twin mesogenic type epoxy resins (DGEnMA, n = 4, 6, 8, 10, 12) having different lengths of alkyl chain as a flexible spacer and the same curing agents (n′BABs). Combinations of the same concentrations of chemical structures in the basic units of the network structure were applied, and the thermal and mechanical properties of their curing systems were investigated. The fracture energy of each system increased considerably with the increase of the alkyl chain length that adjoins the two mesogenic groups in the epoxy resins. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 44244.     

Development Of Cvt Control System And Its Use For Fuel‐Efficient Operation Of Engine

Continuously variable transmission (CVT) provides an automobile with the ability to change the gear ratio continuously, which can then improve not only ride quality such as acceleration performance but also fuel‐efficiency. However, to take advantage of the ability, a control system that can precisely control the gear ratio is required. This paper proposes such a control system for a belt‐driven CVT system. For controller design, first the CVT system is modeled by analytical and experimental approaches. The resultant static and dynamic characteristics provide a nonlinear first‐order model with an uncertain time constant and time delay. The nonlinear steady‐state gain is adjusted to one by a gain‐scheduled pre‐compensator. Thereby the plant model becomes a linear first‐order lag system with a dead time. The next step is controller design using the plant model. To guarantee stability and control performance against the parameter variation and time delay, the μ‐synthesis, a robust control method, is employed for feedback control. In addition, a feedforward controller is incorporated into the feedback control system to obtain better output response. The feedforward controller is given by a combination of the inverse system of the plant and a reference model that gives desired output response. As a result, the control system becomes a two‐degree‐of‐freedom control system. To evaluate the performance of the control system and its effectiveness on the fuel‐efficiency, computer simulation and driving tests were conducted. The simulation and experiment results prove that the proposed control system can make the gear ratio track a reference output quickly and precisely in the presence of the uncertainties. The results also show that the control system improves fuel‐efficiency by changing the gear ratio so that the engine torque and its revolution speed can satisfy optimum‐efficiency operating condition.