湿法氧化锌对天然橡胶性能的影响

研究湿法氧化锌FF和HR对天然橡胶(NR)性能的影响,并与普通氧化锌(间接法)对比。结果表明:与普通氧化锌相比,湿法氧化锌FF和HR的活化和补强作用显著,添加湿法氧化锌FF和HR会缩短NR胶料的焦烧时间和t90,增大Fmax;在氧化锌用量相同时,3种氧化锌的NR硫化胶的拉伸强度由大到小的顺序为湿法氧化锌FF、湿法氧化锌HR和普通氧化锌,定伸应力由大到小的顺序为湿法氧化锌HR、湿法氧化锌FF和普通氧化锌,拉断伸长率由大到小的顺序与定伸应力相反;添加普通氧化锌的NR胶料的Payne效应较弱;氧化锌用量增大时,3种氧化锌的NR硫化胶的储能模量增大,损耗因子减小。     

高盐高有机制药废水污泥电渗透高干脱水

为研究高盐高有机制药废水污泥的电渗透脱水效果，深入认识化学污泥的电脱水过程，本文采用电渗透高干脱水技术对经抽滤脱水的高盐高有机制药废水化学污泥进行深度脱水，考察了泥饼初始pH的改变对污泥电渗透高干脱水过程中阴阳极污泥的含水率、电流、电导率、pH、zeta电位与能耗的影响，验证了对高盐高有机制药废水污泥实行电渗透高干脱水的可行性，解析了化学污泥电渗透脱水过程的机制。结果表明，泥饼pH为2、3、4时，zeta电位为正值，电渗流反向流动，无法脱水；pH增至5时，zeta电位为负值，电渗流从阴极脱除，污泥含水率从53.2%降至44.8%，脱水效果最好；但pH增至6时，脱水量有所降低。污泥电导率随pH的增加而降低。pH为5时初始电流最大。脱水15min时，即污泥含水率降至45.5%时，能源利用率最高。     

Isolation and identification of two major acylated anthocyanins from purple sweet potato (Ipomoea batatas L. cultivar Eshu No. 8) by UPLC‐QTOF‐MS/MS and NMR

In recent years, researches on the isolation and preparation of monomeric anthocyanins have intensified because of the requirements of quantitative and structure–bioactivity relationship analyses. However, simple and effective methods about the scale of monomeric anthocyanins from the natural purple sweet potato powder are rarely reported. In this study, high molecular weight acylated monomeric anthocyanins were isolated from purple sweet potato (Ipomoea batatas L. cultivar Eshu No. 8) via the combination of column chromatography and semi‐preparative HPLC technology and identified mainly by ultra‐high‐performance liquid chromatography quadrupole time‐of‐flight tandem mass spectrometry/mass spectrometry (UPLC‐QTOF‐MS/MS) and ¹H and ¹³C nuclear magnetic resonance (NMR). Two major acylated anthocyanins were unambiguously determined as peonidin 3‐O‐(6‐O‐(E)‐caffeoyl‐(2‐O‐(6‐O‐p‐hydroxybenzoyl)‐β‐D‐glucopyranosyl)‐β‐D‐glucopyranoside)‐5‐O‐(β‐D‐glucopyranoside) and peonidin 3‐O‐(6‐O‐(E)‐caffeoyl‐(2‐O‐(6‐O‐(E)‐feruloyl)‐β‐D‐ glucopyranosyl)‐β‐D‐glucopyranoside)‐5‐O‐(β‐D‐glucopyranoside). The results of this study may help promote the purification of high molecular weight acylated anthocyanins from purple sweet potato as well as from other plant materials in nature.     

How hydrogen-storage material affects the decomposition of nitramine explosive: CPMD investigations of LAB-doped CL20

As the most popular high-energy explosives, 2,4,6,8,10,12-hexanitro-2,4,6,8,10,12-hexaazatetracyclo [5.5.0.0.0] dodecane (Simplified as HNIW or CL20) attracts many attentions for improving its detonation appearance in the application. Here we introduce hydrogen-storage compounds into explosives to estimate the possible improved detonation performances by Car-Parrinello molecular dynamics (CPMD) simulation, where we construct lithium amidoborane (LAB) doped CL20 as the initial structure. Almost all the interactions between hydrogen and CL20 appear exothermic properties, which indicate LAB increases the enthalpies of detonation. The results suggest explosive mixed with hydrogen-storage material is possibly a new field of energetic compound.     

Sol–Gel‐Derived High‐Performance Stacked Transparent Conductive Oxide Thin Films

Single‐ and multi‐layer transparent conductive oxide (TCO) thin films exhibiting high performance, good packing density and low surface/interface roughness are deposited on silica glass substrates by the sol–gel method. The crystal and microstructural properties of the TCO thin films are evaluated as an alternate to films prepared by ultra‐high vacuum deposition. Tin‐doped indium oxide (ITO) thin films produced using a two‐step drying process showed low surface roughness because of dense packing structure not only horizontal but also vertical directions. As a result, electrical conductivity, carrier concentration, carrier mobility, and optical transmittance of 2.3 × 10³ S/cm, 8 × 10²⁰ cm^?3, 18 cm²/Vs, and over 98% at 500 nm, respectively, were achieved. A multilayer ZnO/ITO stacked structure was also fabricated using the sol–gel process. Our findings suggest that solution‐based methods show promise as an alternative to existing ultra‐high vacuum methods to fabricate TCO thin films.     

飞秒激光加工单晶金刚石制备正前角磨削工具

目的制造一种磨粒有序排布、具有正前角的无结合剂端面金刚石磨削工具。方法采用波长为1030 nm、脉宽为250 fs的钛蓝宝石飞秒激光对单晶金刚石(SCD)进行烧蚀加工,首先研究加工工艺参数(特别是烧蚀轨迹间距)对金刚石加工效率及表面质量的影响。采用预先设计的激光扫描路径,基于优化后的工艺参数在SCD表面加工出微磨粒阵列结构,各磨粒呈方锥台形结构,其顶部倾斜角约为100°。在此基础上,对微磨粒阵列进行烧蚀加工,将所有微磨粒顶部的倾斜角减小至小于90°。结果当激光烧蚀轨迹间距为10.0μm时,烧蚀加工表面RMS粗糙度最小。确定了一种微磨粒边缘倾斜角小于90°且磨粒有序排布的新型无结合剂金刚石端面磨削工具的激光制备方法和工艺,采用该工艺加工的磨削工具表面质量好,轮廓精度高,磨粒平均正前角约为9.80°。结论采用飞秒激光可以高质量、高效率地制备出磨粒有序排布的新型正前角无结合剂金刚石端面磨削工具,该工具有望在硬脆材料磨削中减小磨削力,提高材料表面完整性。     

河南WR-1地热井降压试验水位校正的应用研究

一般的单井稳定流抽水试验,可直接利用从孔口测得的水位降深与对应的流量关系,求取含水层的水文地质参数。但对地热井而言,由于在抽水过程中,井筒内水温的变化可对井中水位产生较大影响,故不宜直接利用降压试验前测得的静水位埋深和孔口所测的水位降深值,而应该进行静水位和动水位的校正(刘永贵,2016),才能与观测的水位埋深、水量、水温相匹配进行参数计算(高新智,2015)。文章以尉氏县WR-1地热井馆陶组降压试验静水位、动水位校正实例,阐述地热井降压试验水位校正的有效性和必要性。     

电气设备引发火灾及其爆炸原因

电气设备存在着火灾和爆炸危险性。为消防电气设备的火灾和爆炸隐患,对其原因进行分析,并提出相应防范措施。