Enhancement of glass-ceramic performance by TiO2 doping: In vitro cell viability,proliferation, and differentiation

A new TiO₂-containing bioactive glass and glass-ceramics based on 50SiO₂-(45-X)CaO-(XTiO₂)-5P₂O₅ system was designed using a sol–gel technique (where X = 5, 7.5 and 10 wt %). The roles of the crystallization behavior and physicochemical characteristics of the designed glass and glass-ceramics which were played in the introduction of TiO₂ substitutions were investigated. Moreover, cell proliferation and differentiation were evaluated against human osteosarcoma cells (Saos-2). The TiO₂/CaO replacements led to the formation of a stronger glass structure and thus increased thermal parameters and the chemical stabilization of the designed materials. The FTIR data confirmed the existence of Ti within the glass and glass-ceramics samples, and no remarkable effect on their chemical integrity was observed. The XRD patterns indicated that calcium-containing minerals, including Ca₂SiO₄,Ca₃(PO₄)₂, Ca(Ti,Si)O₅, CaTiSiO₅, and Ca₁₅(PO₄)₂·(SiO₄)₆ phases were developed as a role of structure/texture under the applied heat-treatment. The results of the cytotoxicity test proved that a safe sample dose is 12–50 μg/ml, at which cell viability is ≥ 85%. The cell differentiation determined by ALP test proved the superiority of glass-ceramics compared with their native glasses. Therefore, the obtained materials could be safely used as novel biocompatible materials for the regeneration of bone tissue.     

Preparation of Electrolytic Quasi-Solid-State Nanofibers for Dye-Sensitized Solar Cells

JOM - Nanofibers were prepared from a poly(acrylonitrile-co-vinyl acetate) [P(AN-co-VAC)]/polyvinylidene fluoride (PVDF) blend and used as a quasi-solid (QS) electrolyte for dye-sensitized solar...     

Novel CPG algorithm for tracking fast sudden changes based on tangent rule

ABSTRACT

This paper proposes a novel tracking method to deal with fast changes of solar irradiation and power limit change in order to increase tracking efficiency. This goal is achieved by estimating (i) next operating mode and (ii) next step point with the use of tangent rule in triangle. After every fast response to sudden changes, accurate response phase starts in order to track desired power in each operating mode by adaptive step size. Drift problem in defining next operating mode is eliminated in proposed method by estimating next operating mode, and settling time is decreased to about 25 percent of settling time of other methods by estimating next step point. Simulation and experimental results show the performance of proposed method.     

The impact of alphabet size on pattern complexity of maxmin-$$\omega$$ω cellular automata

Natural Computing - We present an analysis of an additive cellular automaton (CA) under asynchronous dynamics. The asynchronous scheme is maxmin-$$\omega$$, a deterministic system, introduced in...     

Effect of cellulose acetate/cellulose triacetate ratio on reverse osmosis blend membrane performance

Surface functionalization and modification including the grafting process are effective approaches to improve and enhance the reverse osmosis (RO) membrane performance. This work is aimed to synthesize grafted/crosslinked cellulose acetate (CA)/cellulose triacetate (CTA) blend RO membranes using N-isopropylacrylamide (N-IPAAm) as a monomer and N,N-methylene bisacrylamide (MBAAm) as a crosslinker. The morphology of these membranes was analyzed by scanning electron microscopy and their surface roughness was characterized by atomic force microscopy. The performance of these membranes was evaluated through measuring two major parameters of salt rejection and water flux using RO unit at variable operating pressures. It was noted that the surface average roughness obviously decreased from 148 nm for the pure CA/CTA blend membrane with 2.5% CTA to 110 nm and 87 nm for the grafted N-IPAAm and grafted/crosslinked N-IPAAM/MBAAm/CA/CTA-RO membranes, respectively. Moreover, the contact angle decreased from 51.98° to 47.6° and 43.8° after the grafting and crosslinking process. The salt rejection of the grafted CA/CTA-RO membrane by 0.1% N-IPAAm produced the highest value of 98.12% and the water flux was 3.29 L/m²h at 10 bar.     

Failure Analysis and Remedy Procedure for Cracking of Fuel Nozzles in a Gas Turbine

A common failure in a certain type of gas turbine, observed during the first periodic inspection, is radial cracks in the tip plate of gas fuel nozzles. Here, each gas turbine has 18 nozzles. In all nozzles and in all similar units, these cracks of lengths ranging from 1 mm to a maximum of 14.5 mm are observed. As prescribed by the manufacturer, the defective part must be removed and replaced by welding and machining of a new one. But this problem is repeated and observed in the next periodic visits, and in all units. Depending on the number of nozzles in each gas turbine unit and the number of units in total, these repairs are very expensive and time-consuming. In this paper, the failure is analyzed and the causes of the cracks in the nozzles are investigated. Studies show that the main causes of nozzle failure are residual stresses caused by welding and thermal stresses caused by the start-up and shutdown processes. According to results, a solution has been proposed to release these residual and thermal stresses. After the implementation of this method in 1998, no more failure has been reported by the repair team, which proves the effectiveness of this solution. Since this paper has been prepared based on technical reports from the years between 1996 and 1998, the cited references of this paper are these technical reports.     

Engineering geological properties of the pyroclastic cone-shaped rocky houses of Kandovan,Iran

Bulletin of Engineering Geology and the Environment - Kandovan is one of the geo-tourism attractions in the East Azarbaijan Province of Iran, where rural houses were carved within the cone-shaped...