ACTNET: End-to-End Learning of Feature Activations and Multi-stream Aggregation for Effective Instance Image Retrieval

International Journal of Computer Vision - We propose a novel CNN architecture called ACTNET for robust instance image retrieval from large-scale datasets. Our key innovation is a learnable...     

Effect of coupling agent content on properties of composites made from polylactic acid and chrysanthemum waste

Chrysanthemum flower is among one of the highly sought after and widely planted flower crops, in particular for cultural and religious ceremonies. However, the chrysanthemum stem and stalk have little value and usually discard as by‐product waste from floristry. The objective of this research is to investigate the potential value of utilizing chrysanthemum stem and stalk as reinforcing fillers for thermoplastic composites. In this study, 2‐mm thick composite sheet containing predefined formulations of polylactic acid (PLA), chrysanthemum waste filler (CWF) ranging from 15 to 60 phr, and maleated polyethylene (MAPE) coupling agent up to 5 phr were prepared with the aid of Haake internal mixer and compression molding. The effect of MAPE loading on tensile, thermal, and morphological properties of PLA/CWF composites was investigated. The findings revealed that PLA/CWF composite attained improved tensile modulus compared to the neat PLA, and the tensile modulus increases with higher concentration of CWF. However, both tensile strength and elongation at break reduces with increase loading of CWF. Overall, PLA/CWF composites with MAPE shows better performance compared to those without MAPE, where an optimum strength of 21.8 MPa can be achieved with 60 phr CW and 3 phr MAPE. The measured tensile strength is comparable to alternatives natural fiber thermoplastic composites demonstrating its potential to be used in non‐structurally demanding application. J. VINYL ADDIT. TECHNOL., 26:10–16, 2020. © 2019 Society of Plastics Engineers     

Prolonged tamoxifen exposure selects a breast cancer cell clone that is stable in vitro and in vivo

The effects of long-term tamoxifen exposure on cell growth and cell cycle kinetics were compared between oestrogen receptor (ER)-positive (MCF-7) and ER-negative (MDA-MB-231) cell lines. In the MCF-7 cell line, prolonged tamoxifen exposure (0.5 mumol/l for > 100 days) blocked cells in G0-G1 of the cell cycle, and slowed the doubling time of cells from 30 to 59 h. These effects corresponded to an increase in the cellular accumulation of tamoxifen over time [mean area under concentration curve (AUC) = 77.92 mumoles/10(6)/cells/day]. In contrast, in the MDA-MB-231 cell line, long-term tamoxifen exposure had no obvious effect on the doubling time, and reduced cellular tamoxifen accumulation (mean AUC = 50.50 mumoles/10(6)/cells/day) compared to the MCF-7 cells. Flow cytometric analysis of MDA-MB-231 cells demonstrated that a new tetraploid clone emerged following 56 days of tamoxifen exposure. Inoculation of the MDA-MB-231 tetraploid clone and MDA-MB-231 wildtype cells into the opposite flanks of athymic nude mice resulted in the rapid growth of tetraploid tumours. The tetraploid tumours maintained their ploidy following tamoxifen treatment for nine consecutive serial transplantations. Histological examination of the fifth transplant generation xenografts revealed that the tetraploid tumour had a 25-30 times greater mass, area of haemorrhage and necrosis, a slightly higher mitotic index and was more anaplastic than the control neoplasm. The control wildtype MDA-MB-231 tumours maintained a stable ploidy following tamoxifen treatment until the eighth and ninth transplantation, when a tetraploid population appeared, suggesting that tamoxifen treatment may select for this clone in vivo. These studies suggest that prolonged tamoxifen exposure may select for new, stable, fast growing cell clones in vitro as well as in vivo.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Factors affecting cloud point analysis of palm oleins

Some of the factors affecting cloud point determination of palm oleins are described. These are the type of container used, method of stirring, rate of stirring and bath temperature. The repeatability and reproducibility standard deviations of the method are determined from collaborative trials. Recommendations for the test are made to reduce the large variations among laboratories.     

Effect of rotor profiles on the torque of a switched-reluctancemotor

The authors examine effects on the torque that simple variations of the standard rotor pole face profile could have, basically from an elementary viewpoint of how the modified profiles affect the distribution and magnitude of the radial and tangential components of the flux density. It is observed that the average torque is mostly affected by changes that alter the dominant radial component, such as changes in the effective air gap length. The other observation that an increase in the average torque can also be obtained by a favorable shift in the torque versus angle characteristics by relatively simple changes of the rotor pole profile is not so well known. Such a shift that reduces the slope of the torque angle characteristic, skewing the curve towards the unaligned position, has two advantages: one is that the phase inductance is at its maximum positive slop and, hence, the maximum torque, when the phase is energized; second, the flatter inductance profile near the aligned position when the phase current is to be commutated would allow a faster drop off of the commutated current and, thus, a smaller negative torque