Research and development of liquid hydrogen (LH2) temperature monitoring system for marine applications

Monitoring the temperature in liquid hydrogen (LH₂) storage tanks on ships is important for the safety of maritime navigation. In addition, accurate temperature measurement is also required for commercial transactions. Temperature and pressure define the density of liquid hydrogen, which is directly linked to trading interests. In this study, we developed and tested a liquid hydrogen temperature monitoring system that uses platinum resistance sensors with a nominal electrical resistance of approximately 1000 Ω at room temperature, PT-1000, for marine applications. The temperature measurements were carried out using a newly developed temperature monitoring system under different pressure conditions. The measured values are compared with a calibrated reference PT-1000 resistance thermometer. We confirm a measurement accuracy of ±50 mK in a pressure range of 0.1 MPa–0.5 MPa.     

Isolation of antimicrobial agent from the marine algae Cystoseira hakodatensis

Cystoseira hakodatensis is an unutilised brown algae belonging to family Sargassaceae. A crude methanol extract from the algae showed inhibitory effects on the growths of Bacillus cereus and Bacillus licheniformis. To isolate the major antimicrobial agent, a sequential active‐guided isolation procedure was applied: liquid–liquid extraction, column chromatography and bio‐autography. A marked antimicrobial agent (active α) was isolated in hydrophobic fraction and was determined to phenolics without carbohydrates and proteins by phytochemical test. Regarding the antimicrobial potential, the isolated active α showed better inhibitory effects against B. cereus and B. licheniformis at 2 and 4 times of lower concentrations (62.5 and 31.3 μg mL^?1) in comparison with epigallocatechin gallate. These results showed that C. hakodatensis is a potential source of antimicrobial agent capable of preventing the growth of the two bacteria.     

Distribution of carbon contamination in MgAl2O4 spinel occurring during spark-plasma-sintering (SPS) processing: I – Effect of heating rate and post-annealing

Carbon contamination from the carbon paper/dies during spark-plasma-sintering (SPS) processing was examined in the MgAl₂O₄ spinel. The carbon contamination sensitively changes with the heating rate during the SPS processing. At the high heating rate of 100 °C/min, the carbon contamination having organized structures occurred over almost the entire area from the surface to deep inside the SPSed spinel disk. In contrast, at the slow heating rate of 10 °C/min, the carbon contamination having disordered structures occurred only around the surface area. The carbon phases transform into high pressure CO/CO₂ gases by post-annealing in air and lead to pore formation along the grain junctions. The pore formation significantly occurs at the high heating rate due to the large amount of the contaminant carbon phases. This suggests that if once the carbon contamination was formed in the materials, it is very difficult to remove the carbon phases from the materials.     

Driving voltage reduction in a two-phase CCD by suppression ofpotential pockets in inter-electrode gaps

This study reports an optimum design for a two-phase charge-coupled device (CCD) and limitations on its driving voltage reduction. The two-phase CCD to be used as a horizontal-CCD (H-CCD) in a CCD image sensor requires low-voltage and high-speed operation. Reducing the driving voltage, however, may induce potential pockets in the channel under the inter-electrode gaps which results in a fatal decrease in charge-transfer efficiency. In this case it is necessary to optimize the CCD design to be free of pocket generation. For this requirement, we conducted two-dimensional (2-D) device simulations for the two-phase CCD, whose potential barriers are formed by boron ion-implantation. Our simulations indicated that the edge position of the potential barrier region and the dose of boron-ion implantation would be important parameters for controlling the size of potential pockets. At an optimum edge position and a boron dose, the minimum driving voltage appears to be reducible to 1.1 V. Characteristics of potential pockets and methods of their suppression are also discussed     

Iodine-123-BMIPP myocardial washout and cardiac work during exercise in normal and ischemic hearts

Due to the changes in the frequency of penicillin-resistant strains of S. pneumoniae, it is necessary to perform surveillance studies of bacterial resistance. Isolates from the upper respiratory tract of asymptomatic children have been useful. There is no information about the difference between isolates from children with and without upper respiratory tract infection (URTI). The objective of the authors in this paper is to establish the prevalence of carrier-state, serotype and antimicrobial resistance of S. pneumoniae isolates from children with and without acute upper respiratory tract infection (URTI) in a rural area in Mexico. A cross-sectional comparative study was performed in Tlaxcala, Mexico. Children from one month 5 years of age were included. Nasopharyngeal swabs were obtained. Identification was done by international microbiology standards. Serotyping was done by the capsular Quellung test. The susceptibility testing was performed by the agar dilution method. Four-hundred and fifty patients were included. S. pneumoniae was isolated in 134 children (29.7%). Frequency of carriers was greater in patients with URTI (107/323) than without URTI (27/127) (33.1% vs. 21.1% p = 0.012, OR 1.84, IC 95% 1.1-3.08). The six most frequent serotypes were: 6B (16.4%); 19F (11.9%); 19A (6.7%); 14, 23F, and 35 (5.2% each), with no difference among the groups. Only 3% of the strains had high level resistance to penicillin, and 12.6% had intermediate resistance, and for ampicillin 4%, amoxicillin 4%, amoxicillin-clavulanate 4%, ceftriaxone 3%, cefotaxime 1.5%, erythromycin 6%, miocamycin 3%, chloramphenicol 4%, and vancomycin 0%. Trimethoprim-sulfamethoxazole resistance was very high (42%). In conclusion, colonization is higher in children with URTI. Five of the most frequent serotypes identified in this study were the same as those identified in patients with S. pneumoniae invasive diseases in Mexico City. In Tlaxcala, Mexico, beta-lactams could be the drug of choice for the treatment of S. pneumoniae lower respiratory tract infections. It is necessary to perform clinical assays to evaluate the efficacy of trimethoprim-sulfamethoxazole due to the high resistance in vitro.     

Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers