An efficient manufacturing method for I-shaped cross-sectional CFRP beam with arbitrary arrangement of carbon fiber using electro-activated resin molding

Abstract

The I-shaped cross-sectional beam of CFRP (CFRP I-beam) is usually manufactured by the continuous protrusion method. Carbon fibers can only be arranged in the longitudinal direction. The CFRP I-beam with arbitrary arrangement of carbon fiber was manufactured with applying the electro-activated deposition molding method. The carbon fiber fabric was immersed in the deposition solution and energized, epoxy resin precipitated around carbon fiber and impregnated. The resin-impregnated fabric was installed to the mold, and the CFRP I-beam was fabricated. The CFRP I-beam was subjected to three-point bending tests, and the relationship between load-deflection was simulated by finite-element analysis.     

A comparative study of DPSK and OOK WDM transmission over transoceanic distances and their performance degradations due to nonlinear phase noise

We have compared experimentally the transmission performance of return-to-zero differential phase-shift keying (RZ-DPSK) with RZ-ON-OFF keying (OOK), nonreturn-to-zero differential phase-shift keying (NRZ-DPSK), and NRZ-OOK for 100/spl times/10-Gb/s transmission with a spectral efficiency of 0.22 b/s/Hz over transoceanic distances. The Q degradation of the RZ-DPSK after transmission over 9180 km was 3 dB greater than that of RZ-OOK. The experimental results clearly showed the major cause of degradation for DPSK is not cross-phase modulation but self-phase modulation. The calculated nonlinear phase noise, i.e., the Gordon-Mollenauer effect, agreed with the experimental results. A distributed-Raman-amplifier assisted erbium-doped-fiber-amplified transmission line acted well in reducing the nonlinear phase noise.     

Solution intercalation of polystyrene and the comparison with poly(ethyl methacrylate)

Polystyrene nanocomposites have been prepared via solution intercalation method. Combination of wide-angle X-ray diffraction and thermogravimetric analysis is used to study the effect of solvents on the morphology of the nanocomposites as a function of the amount of residual solvent. d-Spacing of the polystyrene nanocomposites has a minimum value when the residual solvent concentration is between 2 and 4 wt%. Different interaction level between the solvent molecules and polymer chains is considered to be the reason for this special d-spacing change behavior. By comparing the solution intercalation of polystyrene and poly(ethyl methacrylate) from different solvents, it is concluded that the interactions between polymer-surfactant, solvent-surfactant, and polymer-solvent play important role for the solution intercalation of polymers.     

Suppression control method for torque vibration of three-phase HB-type stepping motor utilizing feedforward control

This paper proposes a method to reduce the vibration of the three-phase HB-type stepping motor with cogging torque by the feedforward compensation control. The compensation signal to suppress the vibration of the motor frame is obtained by the repetitive controller installing an online Fourier transformer and utilizing an acceleration sensor attached to the motor frame or an acoustic sensor such as a microphone placed close to the frame. The sensor is used only for the acquisition of the feedforward compensation data. The feedforward compensation signal at an arbitrary operating point is derived from the amplitude and phase data of the frequency components and the operating point data. Compensation data obtained by the repetitive controller is applied to the operating point changed by reference frequency and load condition in steady state. The compensation signal for the new operating point will be generated from compensation data utilizing polynomial equation approximation and linear interpolation method. The effectiveness of this proposed method is confirmed by the experimental results.     

Digitally tunable optical filters using arrayed-waveguide grating(AWG) multiplexers and optical switches

Two novel configurations for digitally tunable optical filters based on arrayed-waveguide grating (AWG) multiplexers are described in detail with emphasis on the connection of the AWG multiplexer and optical switches. Performance comparisons show that conventional configurations are disadvantaged by the switch size required and loss imbalance among the optical frequency-division-multiplexed (FDM) channels; the proposed configurations require only O(√(N)) switch elements to select one of N FDM channels, and the loss imbalance is lower by up to 75% in decibel     

Tuning-current splitting network for three-section DBR lasers

A simple current-splitting network for DBR-laser frequency tuning is proposed that distributes a single control current among two tuning sections and can adjust the current distribution without yielding impedance mismatching. The nonlinear characteristics of the tuning sections realise the non-proportional current splitting suitable for continuous tuning; 470 GHz (3.8 nm) tuning range is achieved     

Breakdown characteristics of oil and paper insulation for a very fast transient voltage

This paper describes the dielectric breakdown characteristics of oil and oil‐impregnated paper for very fast transient (VFT) voltages. Blumlein circuits generate VFT voltages of 60 and 300 ns in a pulse width that simulates disconnecting switching surges in gas‐insulated switch gears. We measured the breakdown voltages of needle‐to‐plane, plane‐to‐plane oil gaps and several pieces of paper between plane electrodes for VFT and lightning impulse voltages. The measured data were formulated in V‐t characteristics and Weibull probability distributions. The inclination n of V‐t characteristics of insulating paper is 150, which is less than n = 13.7 of the plane‐to‐plane oil gap in the VFT time range. The shape parameters of Weibull distribution obtained in this study show that the scattering of breakdown voltages of paper is much less than that of oil. © 2002 Wiley Periodicals, Inc. Electr Eng Jpn, 141(4): 16–24, 2002; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10043     

Continuous hydrolysis of olive oil by lipase in microporous hydrophobic membrane bioreactor

Continuous hydrolysis of olive oil byCandida cylindracea’s lipase was studied in a microporous hydrophobic membrane bioreactor. Olive oil and buffer solution, fed continuously through two compartments partitioned by membrane, caused reaction at the interface of lipase-adsorbed membrane and buffer solution. Fatty acid was obtained in a single phase without being mixed with components of other phases. At all mean residence times, countercurrent flow mode was superior to cocurrent one. The lipase was adsorbed onto the membrane, and its adsorption was suggested to be partially specific from the experiments with enzymes having various levels of purity. The percent hydrolysis depended hyperbolically on the interfacial enzyme concentration. The hydrolysis seemed to be limited by diffusion of fat or fatty acid through the micropores of the membrane at higher interfacial enzyme concentrations. The lipase was stabilized significantly by glycerol added to the buffer solution. Satisfactory performance of the membrane bioreactor was obtained in a longterm continuous operation which lasted for 24 days by feeding buffer-glycerol (18.0%) solution over the adsorbed lipase. The operational half-life of the adsorbed enzyme was 15 days at 40 C.     

Fast Full-Band Device Simulator for Wurtzite and Zincblende GaN MESFET Using a Cellular Monte Carlo Method

A fast full-band device simulator for wurtzite and zincblende GaN using a Cellular Monte Carlo (CMC) approach is reported for wurtzite and zincblende GaN. The full-phonon dispersion relationship including anisotropic polar-optical phonon scattering is taken into account for the wurtzite GaN calculation. In the bulk simulation, the CMC model is about 30–100 times faster than the conventional Ensemble Monte Carlo model at high electric field region. This CMC model is applied to the simulator of MESFET devices, and the calculation speed is significantly improved.