Effect of PyC interface phase on the cyclic ablation resistance and flexural properties of two-dimensional Cf/HfC composites

Composites based on hafnium carbide and reinforced with continuous naked carbon fiber with and without PyC interface were prepared at low temperature by precursor infiltration and pyrolysis and chemical vapor deposition method. The microstructure, mechanical property, cyclic ablation and fiber bundle push-in tests of the composites were investigated. The results show that after three times ablation cycles, the bending strength of samples without PyC interface decreased by 63.6 %; the bending strength of samples with PyC interface only decreased by 37.8 %. The force displacement curve of the samples with PyC interface presented a well pseudoplastic deformation state. The mechanical behavior difference of two kinds of composites was due to crucial function of PyC interface phase including protection of fiber and weakening of fiber/matrix interface.     

Life cycle cost of conventional,battery electric,and fuel cell electric vehicles considering traffic and environmental policies in China

Electric vehicles (EVs) are considered a promising alternative to conventional vehicles (CVs) to alleviate the oil crisis and reduce urban air pollution and carbon emissions. Consumers usually focus on the tangible cost when choosing an EV or CV but overlook the time cost for restricting purchase or driving and the environmental cost from gas emissions, falling to have a comprehensive understanding of the economic competitiveness of CVs and EVs. In this study, a life cycle cost model for vehicles is conducted to express traffic and environmental policies in monetary terms, which are called intangible cost and external cost, respectively. Battery electric vehicles (BEVs), fuel cell electric vehicles (FCEVs), and CVs are compared in four first-tier, four new first-tier, and 4 s-tier and below cities in China. The comparison shows that BEVs and FCEVs in most cities are incomparable with CVs in terms of tangible cost. However, the prominent traffic and environmental policies in first-tier cities, especially in Beijing and Shanghai, greatly increase the intangible and external costs of CVs, making consumers more inclined to purchase BEVs and FCEVs. The main policy benefits of BEVs and FCEVs come from three aspects: government subsidies, purchase and driving restrictions, and environmental taxes. With the predictable reduction in government subsidies, traffic and environmental policies present important factors influencing the competitiveness of BEVs and FCEVs. In first-tier cities, BEVs and FCEVs already have a competitive foundation for large-scale promotion. In new first-tier and second-tier and below cities, stricter traffic and environmental policies need to be formulated to offset the negative impact of the reduction in government subsidies on the competitiveness of BEVs and FCEVs. Additionally, a sensitivity analysis reveals that increasing the mileage and reducing fuel prices can significantly improve the competitiveness of BEVs and FCEVs, respectively.     

9000m顶部驱动钻井装置结构选型研究

为大幅提高钻井效率,针对9 000 m钻井深度对顶驱的设计要求,通过比较顶驱装置关键部分几种典型的结构,提出适合该型号顶部驱动钻井装置的最优结构形式,为后续9 000 m钻井深度顶部驱动钻井装置的研究提供指导和借鉴。     

海绵负载纳米Al2O3复合吸附剂去除水中硒研究

研究制备了海绵负载纳米Al2O3微球的复合吸附剂(NAS),并用于对Se(Ⅳ)和Se(Ⅵ)的吸附。结果表明,合成的纳米Al2O3微球(NAO)的平均尺寸为200~400 nm,在海绵上负载NAO会使其分散性更好。当NAO负载量分别为80 mg/g和60 mg/g时,NAS对Se(Ⅳ)和Se(Ⅵ)的吸附性能为佳,分别需要60、120 min达到平衡,适应pH为2~5;两者均符合准2级动力学模型;NAS对Se(Ⅳ)、Se(Ⅵ)的最大吸附容量分别为137.2、143.9 mg/g,能很好地与Freundlich模型拟合,说明NAS表面不均匀,且属于多层吸附。经过2次的循环,对Se(Ⅳ)和Se(Ⅵ)的去除率有所降低,但均仍保持在一定的水平,说明NAS可再生循环利用。NAS作为一种新型吸附剂去除水中Se具有较好的应用前景。     

WIRELESS BODY-AREA NETWORKS

The last decade has witnessed the convergence of three giant worlds:electronics,computer science and telecommunications.The next decade should follow this convergence in most of our activities with the generalization of sensor networks.In particular with the progress in medicine,people live longer and the aging of population will push the development of wireless person-     

稀土石膏常压酸化法制备硫酸钙晶须的研究

以含稀土的石膏为原料运用常压酸化法合成硫酸钙晶须,探讨了不同工艺条件对生成的硫酸钙晶须形貌的影响,同时还考察了晶型助长剂的种类和晶型助长剂的含量对硫酸钙晶须生长的影响,利用SEM和XRD分别对硫酸钙晶须的表面形貌、物相特征做了表征分析。实验得到制备硫酸钙晶须的最佳的反应条件：稀土石膏质量浓度为0.22 g/mL、反应时间为25 min、盐酸浓度为2.8 mol/L、反应温度为70 ℃、陈化时间为4 h,在此条件下合成的硫酸钙晶须平均长度为61 μm,平均长径比为30.5;通过对比实验选出了CuCl₂作为促进硫酸钙晶须生长的助长剂,在添加5%（质量分数）的CuCl₂的情况下可使硫酸钙晶须长径比从30.5增至41,长度从61 μm增至81 μm。     

原子吸收光谱法测定保护渣中锰含量

采用原子吸收光谱法测定保护渣中锰含量,进行了酸度对测定的影响、试样分解、共存离子干扰、加标回收、精密度分析等试验。结果表明,锰可完全溶解于混合酸溶液中;加入氯化锶,可以消除钠、钙对锰测定的干扰;锰质量浓度在0~12.0μg/mL的范围,工作曲线线性关系良好;加标回收率较高,在97%~102%;测定结果准确度较高,与高碘酸钠光度法分析结果一致性较好。