Interfacial microstructure and mechanical properties of Ti3SiC2 ceramic and TC11 alloy joint diffusion bonded with a Cu interlayer

Reliable joints of Ti₃SiC₂ ceramic and TC11 alloy were diffusion bonded with a 50 μm thick Cu interlayer. The typical interfacial structure of the diffusion boned joint, which was dependent on the interdiffusion and chemical reactions between Al, Si and Ti atoms from the base materials and Cu interlayer, was TC11/α-Ti + β-Ti + Ti₂Cu + TiCu/Ti₅Si₄ + TiSiCu/Cu(s, s)/Ti₃SiC₂. The influence of bonding temperature and time on the interfacial structure and mechanical properties of Ti₃SiC₂/Cu/TC11 joint was analyzed. With the increase of bonding temperature and time, the joint shear strength was gradually increased due to enhanced atomic diffusion. However, the thickness of Ti₅Si₄ and TiSiCu layers with high microhardness increased for a long holding time, resulting in the reduction of bonding strength. The maximum shear strength of 251 ± 6 MPa was obtained for the joint diffusion bonded at 850 °C for 60 min, and fracture primarily occurred at the diffusion layer adjacent to the Ti₃SiC₂ substrate. This work provided an economical and convenient solution for broadening the engineering application of Ti₃SiC₂ ceramic.     

适应不同重力环境的仿壁虎机器人运动仿真

针对不同重力环境下仿壁虎机器人的运动稳定性、运动高效协调性等问题,基于四足机器人的步态规划现状和仿壁虎机器人自身特定的机械结构,设计了仿壁虎机器人在g、0、-g 3种环境下的足端轨迹和运动步态。在ADAMS仿真软件中研究了机器人的运动学和动力学特性,得到了仿壁虎机器人稳定爬行与脚掌黏附力、足端轨迹和运动步态的关系。探讨了仿真结果的合理性和局限性,为仿壁虎机器人在实际环境中的稳定运动奠定了理论基础。     

脉冲高度权重技术测量197Au中子俘获截面

脉冲高度权重技术是利用C_6D_6探测器测量中子俘获截面的一种数据处理方法。在中国散裂中子源(China Spallation Neutron Source,CSNS)的反角白光中子源(Back-n)靶站上,通过测量金靶(~(197)Au)的中子俘获截面,验证了该方法的可靠性。首先利用Geant4蒙特卡罗程序模拟给出了不同靶条件下的探测器效率,脉冲高度权重函数等基本项,使得加权后的探测器效率与γ能量成正比。然后通过实验测量了~(197)Au中子俘获截面。结果表明:测量获得的中子俘获截面数据和ENDF/B-VⅢ.0评价数据相符合,同时发现随着实验靶尺寸的不同和质子束功率的增加,会使得实验本底的扣除误差越来越大。     

生物预处理技术在天然产物提取中的应用研究进展

生物预处理技术运用于天然产物提取是借助微生物或生物酶的作用，在适当条件下对天然资源进行处理，破坏植物原料的细胞壁，促进天然产物释放到提取介质中，以提高分离效率，有助于保证天然产物活性。生物预处理技术按形式可以分为微生物发酵技术和生物酶处理技术。针对2种生物预处理技术的作用机制和应用进行综述，旨在为天然产物开发利用提供参考。     

Controlled Secure Direct Communication Protocol via the Three-Qubit Partially Entangled Set of States

In this paper, we first re-examine the previous protocol of controlled quantum secure direct communication of Zhang et al.’s scheme, which was found insecure under two kinds of attacks, fake entangled particles attack and disentanglement attack. Then, by changing the party of the preparation of cluster states and using unitary operations, we present an improved protocol which can avoid these two kinds of attacks. Moreover, the protocol is proposed using the three-qubit partially entangled set of states. It is more efficient by only using three particles rather than four or even more to transmit one bit secret information. Given our using state is much easier to prepare for multiqubit states and our protocol needs less measurement resource, it makes this protocol more convenient from an applied point of view.     

湖北省保康县荆山玉地球化学特征及其成因分析

荆山玉是湖北省保康县新发现的一个玉石品种,形成于大陆边缘—洋盆区过渡带的热水沉积环境,为晚震旦世—早寒武世灯影组的一种硅质角砾岩:原地震碎角砾岩,由角砾和胶结物二部分构成,角砾局部可拼接;角砾成分为早期硅质岩碎裂产物,胶结物除早期硅质岩碎裂产物外,还有少量后期充填的石英、铁质等,受角砾、胶结物颗粒大小、裂隙发育程度不同的影响,后期热液改造程度不同,角砾和胶结物化学成分存在一定的差异,色调与铁质有关。荆山玉的形成主要经历了三个阶段的演化:第一阶段,低温150～225℃、弱氧化—弱还原条件下热水成因的硅质岩形成;第二阶段,热力膨胀外力作用下,硅质岩局部原地震碎形成硅质角砾岩,热水温度243～340℃,富氧氧化—贫氧过渡环境,红褐色的Fe~(3+)在胶结物、裂隙中富集;第三阶段,热水温度116～127℃、缺氧还原条件,黄色的Fe~(2+)在胶结物、裂隙中富集。