汽爆秸秆对磷矿粉溶解作用及其溶解残渣对小麦生长的影响

为探究生物质对磷矿粉的溶解作用，以玉米秸秆为原料，利用蒸汽爆破（汽爆）技术释放有机酸，在高温水热条件下溶解磷矿粉并制备含磷腐殖酸。通过实验对汽爆秸秆溶解磷矿粉工艺进行了探究及优化，并利用傅里叶红外光谱（FT-IR）、扫描电子显微镜（SEM）和X射线荧光光谱（XRF）进行分析和表征。研究结果表明：15 g汽爆秸秆与1 g磷矿粉以及75 mL水在170℃、加入10% CaCl₂的条件下，反应3 h的溶磷量为1.46 mg/g（以秸秆质量计，下同）。加入与磷矿粉相同质量的NaHSO₄后可使体系pH值降低至2，pH值的降低是磷溶出的关键因素，溶磷量提高为13.10 mg/g。溶磷后的秸秆制备腐殖酸作为小麦盆栽肥料，用量0.2%时，小麦株高、根长、叶绿素含量和相对电导率均显著高于空白组。     

Power flow calculation for a distribution system with multi-port PETs: an improved AC-DC decoupling iterative method

Recently, power electronic transformers (PETs) have received widespread attention owing to their flexible networking, diverse operating modes, and abundant control objects. In this study, we established a steady-state model of PETs and applied it to the power flow calculation of AC–DC hybrid systems with PETs, considering the topology, power balance, loss, and control characteristics of multi-port PETs. To address new problems caused by the introduction of the PET port and control equations to the power flow calculation, this study proposes an iterative method of AC–DC mixed power flow decoupling based on step optimization, which can achieve AC–DC decoupling and effectively improve convergence. The results show that the proposed algorithm improves the iterative method and overcomes the overcorrection and initial value sensitivity problems of conventional iterative algorithms.     

Experimental investigation of power management and control of a PV/wind/fuel cell/battery hybrid energy system microgrid

This paper presents an experimental study of a standalone hybrid microgrid system. The latter is dedicated to remote area applications. The system is a compound that utilizes renewable sources that are Wind Generator (WG), Solar Array (SA), Fuel Cell (FC) and Energy Storage System (ESS) using a battery. The power electronic converters play a very important role in the system; they optimize the control and energy management techniques of the various sources. For wind and solar subsystem, the speed and Single Input Fuzzy Logic (SIFL) controllers are used respectively to harvest the maximum power point tracking (MPPT). To maintain a balance of energy in the hybrid system, an energy management strategy based on the battery state of charge (SOC) has been developed and implemented experimentally. The AC output voltage regulation was achieved using a Proportional Integral (PI) controller to supply a resistive load with constant amplitude and frequency. According to the obtained performances, it was concluded that the proposed system is very promising for potential applications in hybrid renewable energy management systems.     

苏通GIL运输专用机具动力电池类型探讨

GIL运输专用机具是为安全、可靠、高效地完成苏通GIL综合管廊工程GIL单元的运输任务而研制的专用机具,其中动力电池系统设计是整机设计的重点之一。通过对各种常见动力电池优缺点的分析,并结合苏通GIL运输专用机具对动力电池的需求分析,确定了动力电池系统的技术路线,为苏通GIL运输专用机具的研制提供了坚实的基础。     

并联有源滤波器的改进重复控制策略研究

针对三相整流负载产生的6k±1次谐波,提出静止坐标系下的改进型6k±1重复控制策略。同时将比例控制与改进型重复控制相结合,设计改进重复控制并联比例的复合控制结构。为减小改进重复控制中延时环节不为整数的影响,采用基于Lagrange插值近似的FIR滤波器逼近分数延时特性。最后对系统进行稳定性分析和详细设计方法进行推导。通过Matlab仿真验证改进重复控制策略能有效跟踪6k±1次谐波且具有良好的补偿效果,动态响应较快。     

Experimental study on gas–liquid dispersion and mass transfer in shear-thinning system with coaxial mixer

The effects of impeller type, stirring power, gas flow rate, and liquid concentration on the gas–liquid mixing in a shear-thinning system with a coaxial mixer were investigated by experiment, and the overall gas holdup, relative power demand, and volumetric mass transfer coefficient under different conditions were compared. The results show that, the increasing stirring power or gas flow rate is beneficial in promoting the overall gas holdup and volumetric mass transfer coefficient, while the increasing system viscosity weakens the mass transfer in a shearing–thinning system. Among the three turbines, the six curved-blade disc turbine (BDT-6) exhibits the best gas pumping capacity; the six 45° pitched-blade disc turbine (PBDT-6) has the highest volumetric mass transfer coefficient at the same unit volume power.     

CMC jackets for metallic pipes – A novel approach to prevent the creep deformation of thermo-mechanically loaded metals

Steel materials suffer extensive creep by the application at temperatures of about 700?°C and pressures about 350?bar in a power plant environment. The presented concept overwraps a steel pipe with a ceramic matrix composite (CMC) jacket in order to support the steel pipe and provide high temperature strength. Finite Element simulations show the influence of the wall thickness of CMC jacket and the coefficient of thermal expansion (CTE) on circumferential stresses within the hybrid metal ceramic pipe. Suitable fiber and matrix materials were studied, composites fabricated and mechanical properties determined. Finally, a prototype was designed in order to confirm the feasibility of the concept. The lifetime of a pure steel pipe was increased by more than four-fold by the additional CMC jacket.     

Using electroencephalogram to continuously discriminate feelings of personal thermal comfort between uncomfortably hot and comfortable environments

Thermal comfort is an important factor for the design of buildings. Although it has been well recognized that many physiological parameters are linked to the state of thermal comfort or discomfort of humans, how to use physiological signal to judge the state of thermal comfort has not been well studied. In this paper, the feasibility of continuously determining feelings of personal thermal comfort was discussed by using electroencephalogram (EEG) signals in private space. In the study, 22 subjects were exposed to thermally comfortable and uncomfortably hot environments, and their EEG signals were recorded. Spectral power features of the EEG signals were extracted, and an ensemble learning method using linear discriminant analysis or support vector machine as a sub-classifier was used to build the discriminant model. The results show that an average discriminate accuracy of 87.9% can be obtained within a detection window of 60 seconds. This study indicates that it is feasible to distinguish whether a person feels comfortable or too hot in their private space by multi-channel EEG signals without interruption and suggests possibility for further applications in neuroergonomics.     

A comprehensive review of renewable energy resources for electricity generation in Australia

Recently, renewable energy resources and their impacts have sparked a heated debate to resolve the Australian energy crisis. There are many projects launched throughout the country to improve network security and reliability. This paper aims to review the current status of different renewable energy resources along with their impacts on society and the environment. Besides, it provides for the first time the statistics of the documents published in the field of renewable energy in Australia. The statistics include information such as the rate of papers published, possible journals for finding relative paper, types of documents published, top authors, and the most prevalent keywords in the field of renewable energy in Australia. It will focus on solar, wind, biomass, geothermal and hydropower technologies and will investigate the social and environmental impacts of these technologies.     

A simple and effective design strategy to increase power conversion efficiency of linear charge pumps

This paper introduces a simple design strategy to increase the power efficiency of linear charge pumps. The technique exploits a voltage amplitude of the clock signal lower than the supply voltage to reduce the power conversion losses. The nominal output voltage is maintained unaltered by increasing the number of stages.