激光熔注中增强相颗粒对晶粒生长影响的CA模拟

基于元胞自动机法,结合Moore型邻居定义和晶粒生长理论,建立了增强相颗粒SiC对镁合金激光熔注中表层316L不锈钢晶粒生长的影响模型,模型考虑了晶界迁移率和晶界能等因素,实现了不同增强相颗粒体积分数和颗粒尺寸对晶粒生长影响的计算机模拟。结果表明,所建立的模型能较好的模拟晶粒生长过程,所得晶粒生长指数为0.42;增强相颗粒体积分数含量越高,晶粒生长越慢,晶粒尺寸越小;增强相颗粒尺寸越小,晶粒生长的越慢,晶粒尺寸越小,组织越均匀。     

高镁镍渣-磷石膏基复合胶凝材料的制备与性能评价

采用机械研磨的方式将高镁镍渣（HMNS）和磷石膏（PG）筛分至不同粒度，评价了掺不同粒度高镁镍渣和磷石膏复合胶凝材料的力学性能，并对强度形成机制进行了分析。评价了各种配比下浆体的抗压强度和体积稳定性，并分析了其作用机制。试验表明：以HMNS∶PG∶富钙硅质材料ZL=5.4∶3.6∶1配比制得试样的28 d抗压强度为4.43 MPa；室温环境下养护56 d，SP6线性收缩为1.02×10-3 mm/mm，体积稳定性优良；水化产物Ca(OH)2更少，Ca（OH）2与HMNS-PG体系反应生成了CSH凝胶和AFt，结构更为稳定。     

Effect of aging time on discontinuous precipitates,continuous precipitates and mechanical properties of AZ80A magnesium alloy

The evolution of precipitates and mechanical properties of AZ80A magnesium alloy with aging time was studied by in situ observation with SEM, TEM and tensile testing. The results show that the continuous precipitation (CP) phases near the reaction front (RF) are replaced by the discontinuous precipitation (DP) phases at the early aging stage. In DP regions, the elliptical phases coarsen obviously with the increase of aging time, which results in a slightly slow reduction of the intracrystalline hardness of DP regions. In CP regions, some small plate phases reprecipitate simultaneously with the growth of the initial precipitates, which contributes to a slight increase in the intracrystalline hardness in CP regions at the later aging stage. The aging hardening of DP regions is faster and stronger than that of CP regions. However, the age strengthening of CP regions not only compensates for the overaging softening of DP regions but also improves the strength of the alloy.     

Corrosion of hot-dip-galvanised steel and zinc alloy-coated steel in ammonia and ammonium chloride

There are many potential causes of corrosion in animal buildings. Animals exhale large quantities of moisture into the air creating high relative humidity in the building if the moisture is not properly vented. High humidity increases the potential for condensation. In addition, ammonia may be found in large quantities in animal buildings. Ammonia is released from manure and urine. In addition, ammonium chloride is used as a nitrogen source in fertilisers. In this study, the atmospheric corrosion of hot-dip-galvanised steel and zinc alloy-coated steel such as zinc–aluminium and zinc–aluminium–magnesium has been studied in atmospheres containing different levels of ammonia. Investigations have also been conducted at different levels of ammonium chloride. The results are discussed in view of the mechanisms of corrosion of zinc and zinc alloy-coated steel in ammonia and ammonium chloride-containing environments.     

Influence of trace Ca addition on texture and stretch formability of AM50 magnesium alloy sheet

The AM50, AM50–0.1Ca, AM50–0.3Ca and AM50–0.5Ca (wt.%) alloys were hot-rolled and their mechanical properties were determined for the purpose of investigating the effect of trace Ca addition on the texture and stretch formability of AM50 alloy. The results show that the addition of trace Ca can effectively modify the basal texture, which is characterized by the split of basal poles deviated from the normal direction (ND) after the hot rolling, while a broad spread of the basal planes toward the transverse direction (TD) after the annealing. Such change of the basal texture is related to the prior formation of massive compression twins and the decrease of the c/a ratio. Erichsen value increases from 2.25 to 4.21 mm with the increase of Ca content. The enhancement of stretch formability is ascribed to the weakened basal texture, which results in the increase of n-value and the decrease of r-value.     

时效处理对Mg-2.0Zn-0.5Zr-3.0Gd生物降解镁合金组织、力学性能及耐腐蚀性能的影响

通过金相显微分析(OM)、扫描电镜观察(SEM)、透射电镜观察(TEM)和拉伸性能测试研究不同时效时间对Mg-2.0Zn-0.5Zr-3.0Gd生物镁合金显微组织及力学性能的影响,通过质量损失和电化学方法研究合金在模拟体液(SBF)中的耐腐蚀性能。结果表明:时效时间为4~20 h时,合金中析出相的尺寸及数量随时效时间的延长而增加,析出相主要以纳米级棒状和颗粒状的(Mg,Zn)3Gd相形式存在,部分棒状析出相与α-Mg基体具有共格界面关系。合金的强度及伸长率随时效时间的延长先升高后降低。在120 h的浸泡实验中,合金的平均腐蚀速率、点蚀孔洞的数量及孔洞尺寸随时效时间的延长而逐渐增大,腐蚀速率随浸泡时间延长呈现出先减小、后增大、再缓慢减小以及最后趋于稳定的过程。     

铸态及退火态Mg66Al34阳极镁空气电池的性能

制备了铸态及退火态Mg66Al34共晶合金,通过研究该合金的腐蚀及放电行为,考察了该合金作为镁空气电池阳极的放电性能。结果表明:在3.5 mass%NaCl溶液中,铸态合金具有较低的腐蚀速率及放电活性,退火态合金具有高的腐蚀速率及放电活性。在NaCl溶液中加入水溶性石墨烯后,铸态合金具有低的腐蚀速率及较高放电活性。铸态合金低的腐蚀速率是由于在β-Mg17Al12层间形成了黑色富铝氧化物腐蚀产物。     

纯镁表面硅烷/透明质酸钠复合涂层的结构及腐蚀性能研究

纯镁因较快的腐蚀速率使其用于手术移植材料成为了一个障碍。为了控制其降解速率,本研究采用BTSE(1,2-(三乙氧基硅基)乙烷)硅烷化处理和共键嫁接1-(3-二甲氨基丙基)-3-乙基碳二亚胺盐酸盐(EDC)/N-羟基丁二酰亚胺(NHS)交联改性的透明质酸钠涂层的两步制备工艺在纯镁上制备复合涂层。同时使用红外光谱(FTIR)、X射线光电子能谱(XPS)、原子力显微镜(AFM)和静态接触角方法(CA)分析涂层的物化性能,通过电化学行为分析涂层在模拟体液中的耐腐蚀性能。FTIR和XPS结果表明在纯镁表面上成功的制备出复合涂层;其他结果显示,交联透明质酸钠涂层表面较裸镁、硅烷表面更平整、光滑,且呈现出亲水性,提高了其生物活性;与未改性的纯镁相比,复合涂层的腐蚀电流密度减小了2个数量级,阻抗值提高3个数量级,表现出很好的耐腐蚀性能。表明这种复合涂层作为手术移植材料在医学上具有很大的应用前景。     

Zinc-doped hydroxyapatite—zeolite/polycaprolactone composites coating on magnesium substrate for enhancing in-vitro corrosion and antibacterial performance

This work is focused on developing zinc-doped hydroxyapatite—zeolite (ZnHA—Zeo) and polycaprolactone (PCL) composite coatings on magnesium (Mg) substrate to improve the corrosion resistance and antimicrobial properties. Dip-coating technique was used to coat ZnHA—Zeo/PCL on the Mg substrate at room temperature. The samples were subjected to field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR), energy dispersive X-ray spectroscopy (EDX) and antimicrobial potential. Results demonstrated that composite coatings consist of HA, scholzite, zeolite, and PCL phases. EDX spectra indicated the presence of calcium (Ca), silicon (Si), aluminum (Al), zinc (Zn), phosphorus (P) and oxygen (O). The composite surface appeared in spherical-like microstructure on coating with thickness ranging 226–260 μm. Zinc-doped HA—Zeo composite coating had a high corrosion resistance and provided sufficient protection to the Mg surface against galvanic corrosion. Doped ZnHA—Zeo coating samples exhibited superior disc inhibition by confirming antimicrobial activity against the E. coli as compared to HA—Zeo sample. Altogether these results showed that the ZnHA—Zeo coatings not only improved the corrosion resistance, but also enhanced the antimicrobial property and hence they can be used as suitable candidates for implant applications.