Data sharing mechanism of various mineral resources based on blockchain

Basins with various mineral resources coexisting and enriching often occupy an important strategic position. The exploration of various mineral resources is repetitive at present due to unshared data and imperfect management mechanism. This situation greatly increases the cost of energy exploitation in the country. Traditional data-sharing mode has several disadvantages, such as high cost, difficulty in confirming the right of data, and lack of incentive mechanism, which make achieving real data sharing difficult. In this paper, we propose a data-sharing mechanism based on blockchain and provide implementation suggestions and technical key points. Compared with traditional data-sharing methods, the proposed data-sharing mechanism can realize data sharing, ensure data quality, and protect intellectual property. Moreover, key points in the construction are stated in the case study section to verify the feasibility of the data-sharing system based on blockchain proposed in this paper.     

Seismic behavior of geosynthetic-reinforced retaining walls backfilled with cohesive soil

This study investigates the seismic performance of geosynthetic-reinforced modular block retaining walls backfilled with cohesive, fine grained clay-sand soil mixture. Shaking table tests were performed for three ½ scaled (wall height 190 cm) and ¼ scaled model walls to investigate the effects of backfill type, the influence of reinforcement length and reinforcement stiffness effects. The El Centro and Kobe earthquake records of varying amplitudes were used as base acceleration. Displacement of the front wall, accelerations at different locations, strains on the reinforcements, and the visual observations of the facing and the backfill surface were used to evaluate the seismic performance of model walls. The model walls were subjected to rigorous shaking and the walls did not exhibit any stability problems or signs of impending failure. The maximum deformations observed on the models with cohesive backfill was less than half of the deformation of the sand model. The load transfers between the geogrid and cohesive soil was comparable to that of sand and hence the needed reinforcement length was similar as well. As a result; the model walls with cohesive backfills performed within acceptable limits under seismic loading conditions when compared with granular backfilled counterparts.     

A miniature triaxial apparatus for investigating the micromechanics of granular soils with in situ X-ray micro-tomography scanning

The development of a miniature triaxial apparatus is presented. In conjunction with an X-ray micro-tomography (termed as X-ray μCT hereafter) facility and advanced image processing techniques, this apparatus can be used for in situ investigation of the micro-scale mechanical behavior of granular soils under shear. The apparatus allows for triaxial testing of a miniature dry sample with a size of \mathrm{8}\hspace{0.17em}\mathrm{mm}\times \mathrm{16}\hspace{0.17em}\mathrm{mm} (diameter \times height). In situ triaxial testing of a 0.4–0.8 mm Leighton Buzzard sand (LBS) under a constant confining pressure of 500 kPa is presented. The evolutions of local porosities (i.e., the porosities of regions associated with individual particles), particle kinematics (i.e., particle translation and particle rotation) of the sample during the shear are quantitatively studied using image processing and analysis techniques. Meanwhile, a novel method is presented to quantify the volumetric strain distribution of the sample based on the results of local porosities and particle tracking. It is found that the sample, with nearly homogenous initial local porosities, starts to exhibit obvious inhomogeneity of local porosities and localization of particle kinematics and volumetric strain around the peak of deviatoric stress. In the post-peak shear stage, large local porosities and volumetric dilation mainly occur in a localized band. The developed triaxial apparatus, in its combined use of X-ray μCT imaging techniques, is a powerful tool to investigate the micro-scale mechanical behavior of granular soils.     

Operational time-series data modeling via LSTM network integrating principal component analysis based on human experience

Today’s information technologies involve increasingly intelligent systems, which come at the cost of increasingly complex equipment. Modern monitoring systems collect multi-measuring-point and long-term data which make equipment health prediction a “big data” problem. It is difficult to extract information from such condition monitoring data to accurately estimate or predict health statuses. Deep learning is a powerful tool for big data processing that is widely utilized in image and speech recognition applications, and can also provide effective predictions in industrial processes. This paper proposes the Long Short-term Memory Integrating Principal Component Analysis based on Human Experience (HEPCA-LSTM), which uses operational time-series data for equipment health prognostics. Principal component analysis based on human experience is first conducted to extract condition parameters from the condition monitoring system. The long short-term memory (LSTM) framework is then constructed to predict the target status. Finally, a dynamic update of the prediction model with incoming data is performed at a certain interval to prevent any model misalignment caused by the drifting of relevant variables. The proposed model is validated on a practical case and found to outperform other prediction methods. It utilizes a powerful deep learning analysis method, the LSTM, to fully process big condition monitoring series data; it effectively extracts the features involved with human experience and takes dynamic updates into consideration.     

人工砂混凝土性能试验研究

采用正交试验方法配制了不同人工砂取代率、石粉含量、粉煤灰含量的混凝土, 对比了每组混凝土的坍落度, 研究了3 d、28 d龄期混凝土的抗压性能。结果表明: 最优配比的人工砂取代率、石粉含量和粉煤灰含量分别为10%、3%和5%, 此时28 d抗压强度为40.1 MPa, 满足30 MPa的混凝土设计强度。     

Smart firefighting construction in China: Status,problems, and reflections

“Smart firefighting” construction as a part of the “smart city” has been a concern of the public security and fire agencies at all levels. In this study, the status, problems, and reflections of “smart firefighting” construction in China are discussed. A recent survey indicates that China has launched its smart firefighting construction and initially created a new perspective on its regional smart firefighting work based on three main aspects: intelligent disaster perception by Internet of Things (IoT) construction, intelligent disaster prevention by big data construction, and intelligent disaster disposal by emergency rescue platform construction. However, the current smart firefighting construction in China still has some prominent problems such as the data interconnectivity and normalized management of various platforms, the extensibility of smart firefighting platforms, and the intelligent level of smart firefighting researches, which need to be solved urgently. Therefore, we argue that smart firefighting construction in China should establish data interconnectivity, industrial normalized management, 2D/3D geographic information interaction and extension, high-integration fire protection theory, and many other aspects in the near future and truly realize firefighting visualization and efficient data applications for 4D time space. This study could provide valuable reference for smart firefighting and smart city construction.     

The World robot summit disaster robotics category – achievements of the 2018 preliminary competition

The World Robot Summit is a robot Olympics and aims to be held in a different country every four years from 2020. The concept of the Plant Disaster Prevention challenge is daily inspections, checks, and emergency response in industrial plants, and in this competition, robots must carry out these types of missions in a mock-up plant. The concept of the Tunnel Disaster Response and Recovery challenge is emergency response to tunnel disasters, and is a simulation competition whereby teams compete to show their ability to deal with disasters, by collecting information and removing debris. The Standard Disaster Robotics challenge assesses, in the form of a contest, the standard performance levels of a robot that are necessary for disaster prevention and emergency response. The World Robot Summit Preliminary Competition was held at Tokyo Big Sight in October 2018, and 36 teams participated in the Disaster Robotics Category. UGVs and UAVs contended the merits of new technology for solving complex problems, using core technologies such as mobility, sensing, recognition, performing operations, human interface, autonomous intelligence etc., as well as system integration and implementation of strategies for completing missions, gaining high-level results.     

基于MF-R和AWS密钥管理机制的物联网健康监测大数据分析系统

带有传感器的可穿戴式医疗设备不断生成大量数据，由于数据的复杂性，难以通过处理和分析大数据来找到有价值的决策信息。为了解决这个问题，提出了一种新的物联网体系结构，用于存储和处理医疗应用的可扩展传感器数据（大数据）。所提出的架构主要由两个子架构组成：Meta Fog重定向（MF-R）架构和AWS密钥管理机制。MF-R架构使用Apache Pig和Apache HBase等大数据技术来收集和存储不同传感器设备生成的传感器数据，并利用卡尔曼滤波消除噪声。AWS密钥管理机制使用密钥管理方案，目的是保护云中的数据，防止未经授权的访问。当数据存储在云中时，所提出的系统能够使用随机梯度下降算法和逻辑回归来开发心脏病的预测模型。仿真实验表明，和其他几种算法相比，提出的算法具有更小的误差，且在吞吐量、准确度等方面具有一定的优越性。     

化工冶金学家陈家镛

1958年中国科学院化工冶金研究所(现过程工程研究所)的创建,与建国初期的国家经济发展和国防建设的需求紧密相关。1956年陈家镛受到世界著名冶金学家叶渚沛的邀请,到正在筹建中的化工冶金研究所工作。作为国内该领域开拓者和学术带头人,陈家镛院士的学术经历是本文主线。以他带领同事们开展湿法冶金研究为案例,分析了国家重大战略需求与科学技术研究之间的关系。重点介绍了他在冶金、化工、材料等研究领域做出的重要学术贡献,以及将代表性科研成果经过中间试验应用于实际生产、解决企业所面临的技术难题的情况。藉此反映了以过程工程研究所为代表的国立科研机构,围绕国家重大战略需求开展科技攻坚的历程与成果。     

Development and monitoring of an integrated bioprocess for production of a potential malaria vaccine with Pichia pastoris

An engineered variant of the yeast Pichia pastoris was used to produce the potential malaria vaccine D1M1. This paper describes the implementation of an expanded bed adsorption chromatography step into a sequential cultivation process of the yeast in order to link protein expression, cell release, and product capture of the secreted protein in a fully automated plant. The process is operated with a semi-continuous strategy for an integrated production. Process improvements have been achieved using design of experiments. Resulting purities of product achieved up to 87% with recoveries of 51% in a single downstream operation. Furthermore, a multivariate analysis of historical batch data was used to develop a golden batch model for process monitoring.